Microphone 1
Volume
Power
Magnetic
Charging Port
LED Indicator
Multifunction Button
Microphone 2
B C
D
A
ENGLISH
1. Charge
2. Pair
3. Connect
Charge the headphones with the included magnetic charging cable. The
LED indicator will turn from red to blue when charging is complete.
Start with your headphones off. Enter pairing mode by pressing and
holding volume+ until Audrey says “pairing” and the LED indicator flashes
red and blue.
Open your device’s Bluetooth
®
menu and select “Aeropex by AfterShokz.”
Audrey says “connected” and the LED indicator will flash blue one time.
Let us take care of you! We’ve got your back against defects.
Register your Aeropex at
register.aftershokz.com
Multifunction Button (A)
Play / pause music Click once
One beep
Skip to next song
Double-click
while music is playing
One beep
Skip to previous song
Three-click
while music is playing
One beep
Answer call Click once
Two beeps
End call
Answer call waiting and
hang up on current caller
Click once One beep
Press and hold for 2 seconds One beep
Reject a call Press and hold for 2 seconds Two beeps
Device beep
Prompt device assistant Press and hold for 2 seconds
Redial last number Double-click (when idle) "Redial last number"
Function Action Prompt / “Audrey Says™”
Function Action Prompt / “Audrey Says™”
How to Set Up Aeropex
AEROPEX
“Welcome to AfterShokz”
Power on
Press and hold volume+ for 2
seconds
Power off
“Power off”
Press and hold volume+ for 3
seconds
Press and hold both buttons for
2 seconds while on a call
Press and hold both buttons for
3 seconds while music is playing
Click the volume+ or volume-
button while music is paused
Click the volume+ or volume- button
to adjust volume while music is playing
Mute
“Mute on” or “Mute off”
Change EQ
setting
“EQ changed”
“Battery high/Battery medium/
Battery low/Charge me”
Adjust volume
One beep
Check battery
status
AfterShokz LLC
6057 Corporate Dr., East Syracuse, NY 13057
Manufacturer
LED Indicator
Solid red Charging
Solid blue Charging complete
Flashes red and blue Pairing mode
Flashes blue Incoming call
Flashes red every 2 minutes Low battery
Optional Accessories
Earplugs (D)
Use with headphones in environments where it is safe to block out ambient noise,
such as on a train or airplane.
1. Roll earplugs firmly between fingers and place in ears.
2. To adjust EQ settings to reduce or enhance bass while wearing earplugs, press
and hold volume+ and volume- buttons simultaneously.
3. Switch EQ to original setting when you take out the earplugs.
How to Reset Your Headphones
1. Start with your headphones off.
2. Enter pairing mode by pressing and holding volume+ until Audrey says “pairing”
and the LED indicator flashes red and blue.
3. Press and hold the multifunction button, volume+ button and volume- button
(all three buttons) simultaneously for 3-5 seconds, until you hear two beeps or
feel vibrations.
4. Turn your headphones off.
Aeropex
is now reset and can be re-paired to your device.
Volume+ / Power Button (B); Volume- Button (C)
Multipoint pairing allows Aeropex to be connected to two devices at once,
allowing users to seamlessly transition between the two.
1.
Start with your headphones off.
2.
Press and hold volume+ until Audrey says “pairing” and the LED indicator flashes
red and blue.
3.
Press and hold the multifunction button and volume+ button for 3 seconds.
Audrey says "multipoint enabled."
4.
Open your first device's Bluetooth
®
menu and select "Aeropex by AfterShokz."
Audrey says "connected"
5.
Turn your headphones off.
6.
Re-enter pairing mode by pressing and holding volume+ until Audrey says “pairing”
and the LED indicator flashes red and blue.
7.
Open your second device's Bluetooth
®
menu and select "Aeropex by AfterShokz."
Audrey says "connected."
8.
Turn your headphones off.
9.
Turn your headphones on Your headphones are now connected to both devices.
10.
To turn multipoint pairing off Press and hold the multifunction button and volume-
button for 3 seconds. Audrey says "multipoint disabled."
Multipoint Pairing
Charging Port Alert
Part number
AS800 20Hz~20KHz
Specifications
Speaker type
Frequency response
Bone conduction transducer
Bluetooth
®
version Microphone
Sensitivity
105 ± 3dB
-38dB ± 3dBBluetooth
®
v5.0
Warranty
Weight
Battery
2 years
26 g
Up to 10 days
2402MHz~2480MHz 4dBm
A2DP, AVRCP, HSP, HFP
Frequency band Maximum RF output power
Continuous play Standby time
Charge time
Compatible profiles
Battery capacity
Maximum charge voltage
Speaker impedance
5.0V±5%
11.4 omh
Water resistance
IP67
145 mAh
Li-Polymer battery
Up to 6 hours
2 hours
Wireless range
10 m
User Guide
This device has the function of liquid residue detection. During charging, if there is
sweat and other liquid residues in the charging interface,the device will flash
"Red-Blue" lights in the same time the headphone core vibrates and emits a "Di-Di"
warning sound. Please dry the liquid on the charging port of the device then the
device can be charged back to normal.
简体中文
设置你的 Aeropex
1. 充电
2. 配对
3.连接手机
通过磁吸充电头充电。充电完成后指示灯显示为蓝色。
按下开关键5秒进入配对模式，指示灯红蓝交替闪烁。
打开手机蓝牙设置，选择“Aeropex By AfterShokz”， 听到语音提醒“已连接”，
配对成功，蓝灯闪烁一次。
一声提示音
一声提示音
两/一声提示音
一声提示音
一声提示音
两声提示音
设备提示音
“拨打上一个电话”
语音提醒
多功能键（A）
功能 操作 语音提醒功能 操作
播放/暂停音乐 单击
来电时/通话时单击
按住2秒
按住2秒
按住2秒
双击（非播放状态下）
下一首歌曲
接/挂电话
拒接来电
拨打上一次通话
语音拨号
接第二个来电，
同时保持当前通话
接第二个来电，同时
挂断当前通话
单击切换通话
歌曲播放时双击
音量加/开关键 （B）; 音量减 （C）
开机
静音
切换EQ
检查电池电量
调整音量 按下B或C键
通话时同时按住B，C键2秒
播放音乐时同时按住B，C键3秒
音乐暂停时按下B或C键
按住开关键2秒
按住开关键3秒
“电量高”、“电量中等”、
“电量低”或“请充电””
一次提示音
“音效切换”
“静音开”或 “静音关”
“欢迎使用韶音骨传导耳机”
蓝牙协议 A2DP, AVRCP, HSP, HFP
耳机规格
型号 扬声器
频段
麦克风敏感度 蓝牙版本
AS800
20Hz~20KHz
-38dB ± 3dB Bluetooth® v5.0
骨传导扬声器
蓝牙连接距离
电池
持续播放
待机
充电时间
重量
保修
锂电池
6 小时
20天
2小时
2年
10米
26克
多点连接
多点连接允许 Aeopex 能同时连接两台设备，实现两台设备间的无缝切换。
1. 确保耳机处于关机状态。
2. 长按音量+键至少5秒直至红蓝灯交替闪烁，进入配对模式（语音提示：正在配对）
3. 按住多功能键和音量+键3秒 (语音提示: 开启双重配对)
4. 打开第一台设备的蓝牙,并且选择“Aeopex by AfterShokz” (语音提示: 已连接)
5. 关闭耳机
6. 重新进入配对模式
7. 打开第二台设备的蓝牙,并且选择“Aeopex by AfterShokz” (语音提示: 已连接)
8. 关闭耳机
9. 长按音量+键3秒，听到提示音“欢迎使用韶音骨传导耳机”, 此时您的耳机会
自动连接两台设备，并分别听到语音提示“已连接”和“第二台设备已连接”，
至此多点连接完成。
LED 指示灯
电量低
红蓝交替闪烁
蓝色（闪烁）
进入配对模式，按住多功能键，音量+键和音量-键3秒，
直至听到两声提示音并感受到振动。
恢复出厂设置
红色（常亮）
充电中
充电完成
配对模式
来电
蓝色（常亮）
每隔两分钟闪烁红灯
可选配件
耳塞 (D)
在飞机或者列车上，可以配合耳塞一起，来隔绝外界噪音，体验更好的骨传导传音。
1. 将耳塞揉小，并塞入耳朵中。
2. 播放音乐时，同时按住音量加减键，调整到佩戴耳塞时专用的EQ，
感受最佳视听体验。
3. 不用耳塞时，用同样的方式将EQ切换到正常状态。
存储和维护
汗水预警
耳机应当存放在阴凉干燥处。工作温度应在0～45℃。工作在过冷、过热或过度潮湿
环境可能会缩短电池的寿命。
存储很长一段时间后，请在使用前再次充电。
该耳机是防水溅的，但并不完全防水。请不要将耳机浸入水中。
过高音量下听音乐可能会损伤您的听力，声音也可能会失真。
请用柔软的干布清洁耳机。
运动过后请不要立即充电，以免充电口里面可能残留的汗水导致耳机电路损伤。
充电之前保持充电口干燥会降低耳机损坏的风险。
如何联系我们
AfterShokz LLC
6057 Corporate Dr., East Syracuse, NY 13057
生产厂商：深圳市韶音科技有限公司
地址：深圳市宝安区石岩街道石新小区山城工业区14#厂房1楼、4楼
电话：400-6830-858
电池容量
最大充电电压
麦克风阻抗
5.25 V
11.4 omh
防水等级
IP67
145 mAh
关机 “已关机”
本设备具有液体残留检测功能。充电时，如充电接口有汗水等液体残留，设备将会有"
红蓝灯"闪烁，耳机芯震动并发出"滴滴"警示音。请擦干设备充电口上液体，设备可恢
复正常充电。
ENGLISH
Storage And Maintenance
FCC Caution
Industry Canada
In compliance with the essential requirements and other relevant provisions
of the following Directives.
CE Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.Changes or modifications not expresslyapproved by the part responsible
for compliance could void the user's authority to operate the equipment.
Store the headphones in cool and dry place. The working temperature should be
0~45°C(32~113°F).Working in cold/hot environment or highly humid area may reduce the life
of battery.
After storage for a long period, please charge the headphones before using again. The
headphones are water resistant, but are NOT waterproof. Please DO NOT
submerse the headphones in water.
Listening with headphones at high volume may affect your hearing and the audio will be
distorted.
Clean the headphones with a soft dry cloth.
Do not charge right after exercising, in case there's sweat inside the charging port, which could
lead to circuit burning while charging. Keep the charging port dry before connecting to charger
will reduce the risk.
Note
Design and specification are subject to change without notice. For the most up-to- date
product information, please visit www.aftershokz.com.
This device complies with Industry Canada licence-exempt RSS standard(s): Operation is
subject to the following Two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil
ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
Battery
CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
Sound Pressure
Excessive sound pressure from earphones and headphones
can cause hearing loss.
RoHS Directive(2011/65/EU) and (EU)2015/863
WEEE Directive(2012/19/EU)
Please dispose of this product by taking it to your local collection point or recycling center for
such equipment.
RED(2014/53/EU
The CE Declaration of Conformity is available on our website at www.aftershokz.com.
Hereby, Aftershokz declares hat the Bone Conduction Headphones AS800 is in compliance with
Directive 2014/53/U.
The full text of the EU declaration fo conformity is available at the following internet address:
https://aftershokz.com/pages/policies
Manufacturer Declarations
Warranty
AfterShokz LLC gives a warranty of 24 months on this product.For the current warranty
conditions, please visit our website at www.aftershokz.com or contact your AfterShokz
partner. Before putting the product into operation, please observe the respective country
specific regulations.
USB
Due to the used enclosure material, the product shall only be connected to a USB Interface of
version 2.0 or higher. The connection to so called power USB is prohibited.
FCC Statement
"This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help."
radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio
frequency (RF) Exposure Guidelines and RSS-102 of the IC radio
frequency (RF) Exposure rules. This equipment has very low levels of RF energy that is
deemed to comply without testing of specific absorption rate (SAR).
Complies with
IMDA Standards
[Dealer’s Licence No.]
This Equipment Complies With FCC/IC
WARNING:Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
The device must not be co-located or operating in conjunction with any other antenna or transmitter.
"This device complies with FCC's radiation exposure limits set forth for
for an uncontrolled environment"
