Moxa Managed Switch Next Generation OS
v1.0 Command Line Interface
The software described in this manual is furnished under a license agreement and may be used only in accordance with
the terms of that agreement.
Copyright Notice
© 2020 Moxa Inc. All rights reserved.
Trademarks
The MOXA logo is a registered trademark of Moxa Inc.
All other trademarks or registered marks in this manual belong to their respective manufacturers.
Disclaimer
Information in this document is subject to change without notice and does not represent a commitment on the part of
Moxa.
Moxa provides this document as is, without warranty of any kind, either expressed or implied, including, but not limited
to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to the
products and/or the programs described in this manual, at any time.
Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility for
its use, or for any infringements on the rights of third parties that may result from its use.
This product might include unintentional technical or typographical errors. Changes are periodically made to the
information herein to correct such errors, and these changes are incorporated into new editions of the publication.
Technical Support Contact Information
www.moxa.com/support
Moxa Americas
Toll-free: 1-888-669-2872
Tel: +1-714-528-6777
Fax: +1-714-528-6778
Moxa China (Shanghai office)
Toll-free: 800-820-5036
Tel: +86-21-5258-9955
Fax: +86-21-5258-5505
Moxa Europe
Tel: +49-89-3 70 03 99-0
Fax: +49-89-3 70 03 99-99
Moxa Asia-Pacific
Tel: +886-2-8919-1230
Fax: +886-2-8919-1231
Moxa India
Tel: +91-80-4172-9088
Fax: +91-80-4132-1045
Table of Contents
1. About This Manual ............................................................................................................................. 1-1
2. Understanding the Command Line Interface ..................................................................................... 2-1
Accessing the Switch ........................................................................................................................... 2-2
Logging in using the RS-232 Console ............................................................................................. 2-2
Logging in using Telnet ................................................................................................................ 2-5
Command Modes ................................................................................................................................ 2-7
Basic Configuration ...................................................................................................................... 2-7
Understanding All Command Modes ............................................................................................... 2-7
Help Messages ................................................................................................................................... 2-8
Special Usage and Limitations .............................................................................................................. 2-8
Abbreviated Commands ....................................................................................................................... 2-9
No and Default Forms of Commands ................................................................................................... 2-10
CLI Error Messages ........................................................................................................................... 2-10
Command History ............................................................................................................................. 2-11
3. Commands ........................................................................................................................................ 3-1
System .............................................................................................................................................. 3-2
System Management ................................................................................................................... 3-2
Account Management................................................................................................................... 3-6
Network ..................................................................................................................................... 3-9
Time ........................................................................................................................................ 3-20
Port ................................................................................................................................................ 3-28
Port Interface ........................................................................................................................... 3-28
Link Aggregation ....................................................................................................................... 3-36
PoE ......................................................................................................................................... 3-41
Layer 2 Switching ............................................................................................................................. 3-52
VLAN ....................................................................................................................................... 3-52
MAC ........................................................................................................................................ 3-68
QoS ......................................................................................................................................... 3-70
Multicast .................................................................................................................................. 3-86
Network Redundancy ........................................................................................................................ 3-99
Layer 2 Redundancy .................................................................................................................. 3-99
Management .................................................................................................................................. 3-118
Network Management .............................................................................................................. 3-118
Security ......................................................................................................................................... 3-130
Device Security ....................................................................................................................... 3-130
Network Security ..................................................................................................................... 3-139
Authentication ........................................................................................................................ 3-153
Diagnostics .................................................................................................................................... 3-155
System Status ........................................................................................................................ 3-155
Event Notification .................................................................................................................... 3-158
Diagnosis ............................................................................................................................... 3-169
Maintenance and Tool .............................................................................................................. 3-188
1
1. About This Manual
This chapter describes how to use the command line to configure Moxa’s managed Ethernet switches. Besides
the web interface configuration, the command line interface helps system administrators easily and quickly
manage, monitor, and configure Moxa’s managed Ethernet switch.
2
2. Understanding the Command Line
Interface
This chapter helps users understand the command line interface, and demonstrates a general ideal on the
command line operation.
The following topics are covered in this chapter:
Accessing the Switch
Logging in using the RS-232 Console
Logging in using Telnet
Command Modes
Basic Configuration
Understanding All Command Modes
Help Messages
Special Usage and Limitations
Abbreviated Commands
No and Default Forms of Commands
CLI Error Messages
Command History
Moxa Command Line Interface Understanding the Command Line Interface
2-2
Accessing the Switch
Users can connect to the switch using one of two methods: by console or by Telnet.
Logging in using the RS-232 Console
The Moxa managed switch features an RJ45 serial console port to allow users to connect to the switch and
configure settings.
NOTE
Moxa recommends using PComm Terminal Emulator for serial communication. This software is available for
free on the Moxa website. You can use other serial communication software, but the following instructions may
be different.
1. Prepare the included RS-232 serial cable with RJ45 interface.
2. Connect the RJ45 interface end to the console port on the switch, and the other end to the computer.
3. Download the PComm Terminal Emulator from the Moxa website and install the software.
4. In Windows, click Start > Moxa > PComm Terminal Emulator.
5. Click Port Manager > Open to establish a new connection.
The Property window will appear.
Moxa Command Line Interface Understanding the Command Line Interface
2-3
6. On the Communication Parameter tab, select the COM port that will be used for the console connection.
Configure the fields as follows: 115200 for Baud rate, 8 for Data bits, None for Parity, and 1 for Stop
bits.
7. On the Terminal tab, select VT100 as the Terminal Type, and click OK to continue.
Moxa Command Line Interface Understanding the Command Line Interface
2-4
8. Log in to the console using the default login name admin and password moxa. This password will be
required to access any of the consoles (web, serial, Telnet).
9. When successfully connected to the switch, you can start configuring the switch parameters by using
command line instructions.
NOTE
By default, the password assigned to the Moxa switch is moxa. We recommended changing the default
password after logging in for the first time to help keep your system secure.
Moxa Command Line Interface Understanding the Command Line Interface
2-5
Logging in using Telnet
Opening the Moxa switch’s Telnet or web console over a network requires that the PC host and Moxa switch are
on the same logical subnet. You may need to adjust your PC host’s IP address and subnet mask. By default, the
Moxa switch’s IP address is 192.168.127.253 and the subnet mask is 255.255.255.0. Your PC’s IP address
must be configured with an IP in the 192.168.127.xxx and a subnet mask 255.255.255.0.
NOTE
When connecting to the Moxa switch’s through Telnet or the web console, first connect one of the Moxa switch’s
Ethernet ports to your Ethernet LAN, or directly to your PC’s Ethernet port. You may use either a
straight-through or cross-over Ethernet cable.
NOTE
The Moxa switch’s default IP address is 192.168.127.253 with subnet mask 255.255.255.0.
After making sure that the Moxa switch is connected to the same LAN and logical subnet as your PC, open the
Moxa switch’s Telnet console as follows:
1. In Windows, click Start > Run.
Moxa Command Line Interface Understanding the Command Line Interface
2-6
2. In the Windows Run window, enter telnet followed by the Moxa switch’s IP address (192.168.127.253).
You can also issue the Telnet command from a DOS prompt.
3. Log in to the Telnet console using the default login name admin and password moxa.This password will be
required to access any of the consoles (web, serial, Telnet).
4. When successfully connected to the switch, you can start configuring the switch parameters by using
command line instructions.
NOTE
By default, the password assigned to the Moxa switch is moxa. We recommended changing the default
password after logging in for the first time to help keep your system secure.
Moxa Command Line Interface Understanding the Command Line Interface
2-7
Command Modes
Basic Configuration
The CLI (Command Line Interface) for Moxa’s Managed switches can be accessed through either the serial
console or the Telnet console. For either type of connection, access to the CLI is generally referred to as an
EXEC session.
The CLI is organized using different configuration levels. When you first enter the CLI, type “?” to view a list of
basic commands and a description of each function. Type any of the commands shown on the screen to access
the next configuration level. The help panel can be accessed from any configuration level by typing “?”. The
switch will show all the commands for the current configuration mode.
Understanding All Command Modes
The Moxa switch’s CLI supports multiple types of configuration levels for performing different functions. Refer
to the following table for an overview of all available modes.
Mode
Access Method
Prompt
Exit Method
About This Mode
User EXEC
Begin a new session
and login as user.
moxa>
Enter the exit command.
This will return you to the
previous configuration
mode.
Use this mode to
display system
information.
Privileged EXEC
Begin a session and
login as admin.
moxa #
Enter the exit command.
This will return you to the
previous configuration
mode.
Use this mode to
verify commands
that you have
entered.
Global
configuration
Enter the configure
command while in
Privileged EXEC
mode.
moxa (config)#
Enter the exit command.
This will return you to the
previous configuration
mode.
Use this mode to
configure parameters
that will apply to the
entire switch.
Interface
configuration
While in global
configuration mode,
enter the interface
command, followed
by an interface
identification.
moxa
(config-if)#
Enter the exit command.
This will return you to the
previous configuration
mode.
Use this mode to
configure parameters
for the specified
interface.
Refer to the following example of changing configuration modes below.
Moxa Command Line Interface Understanding the Command Line Interface
2-8
Type config at the command prompt to enter configuration mode.
Type exit to return to the previous configuration mode.
Type end from within any configuration level to return to privileged Exec mode.
Help Messages
The CLI supports several types of interactive commands. The Help commands are listed in the following table:
Command
Purpose
?
Shows a brief description of the Help feature in any command level.
Partial command?
Shows a list of commands that begin with the entered character string. There
should be no space between the command and the question mark.
Partial command<Tab>
Completes a partially entered command name. There should be no space
between the command and <Tab>.
Command ?
Shows the keywords, arguments, or both associated with the command. There
should be a space between the command and the question mark.
Command keyword ?
Shows the arguments that are associated with the keyword There should be a
space between the command and the keyword, and between the keyword and
the question mark.
Special Usage and Limitations
If the command contains any special characters, such as *, #, and %, you need to use the quotation marks (“”)
to cover these special characters. Refer to the following figure for an example.
Moxa Command Line Interface Understanding the Command Line Interface
2-9
In addition, you may use a semicolon mark (;) to separate several commands. Refer to the figure below for an
example.
Abbreviated Commands
The exclamation mark “!” can be used to enter the global configuration mode, as shown in the example below.
In addition, you can input one or more letters to quickly see all commands starting with these letters. For
example, type c?, all commands starting with c will be shown. Refer to the figure below as the example.
In addition, when pressing Tab after typing the prefix letter, the syntax of the commands starting with that
letter will be shown. See the figure below for details.
Moxa Command Line Interface Understanding the Command Line Interface
2-10
No and Default Forms of Commands
A “no” command can used to perform the “delete”, “disable”, or “reset to default” functions. Type “no ?” to
check how parameters can be used.
The following example shows how a “no” command can run the “reset to default” function.
The following example shows how “no” can run the “disable” function.
CLI Error Messages
You may encounter some error messages while configuring Moxa’s Ethernet switch. Refer the following table
for an overview of error messages and solutions.
Error Message
Meaning
Solution
% Ambiguous command
The characters you entered are
insufficient for the switch to recognize
the command.
Re-enter the command with a space
between the command and the question
mark (?). The possible keywords with
the command will appear.
% Incomplete command
The keywords or values you entered
are incomplete.
Re-enter the command with a space
between the command and the question
mark (?). The possible keywords with
the command will appear.
% Invalid input detected
at ‘^’ marker.
The command you entered is incorrect.
The point of invalid input will be
indicated by a caret (^).
Enter a question mark (?) to display all
the available commands in this
command mode.
The possible keywords with the
command will appear.
Moxa Command Line Interface Understanding the Command Line Interface
2-11
Command History
Use the Up arrow and Down arrow keys to show to cycle through the history of previously entered commands.
Pressing the Up arrow will display the previously entered command. Pressing the Down arrow will display the
next command in the history.
3
3. Commands
This chapter covers all commands for users to configure Moxa’s managed Ethernet switch.
The following topics are covered in this chapter:
System
System Management
Account Management
Network
Time
Port
Port Interface
Link Aggregation
PoE
Layer 2 Switching
VLAN
MAC
QoS
Multicast
Network Redundancy
Layer 2 Redundancy
Management
Network Management
Security
Device Security
Network Security
Authentication
Diagnostics
System Status
Event Notification
Diagnosis
Maintenance and Tool
Moxa Command Line Interface Commands
3-2
System
System Management
Information Setting
Configure Device Hostname
Commands
hostname text
no hostname
Syntax Description
no
Remove configuration/delete entry/reset to default value
hostname
Configure the device hostname parameters
device-name
The hostname of the device consisting of lower case letters,
numbers, and hyphens
Defaults
hostname: moxa
Command Modes
Global Configuration
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# hostname device-name
device-name(config)# no hostname
moxa(config)#
Error Messages
N/A
Related Commands
N/A
Configure Device Description
Commands
description text
no description
Syntax Description
no
Remove configuration/delete entry/reset to default value
description
Configure the device description parameters
text
The description of the device
Defaults
N/A
Command Modes
Global Configuration
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# description "description data"
moxa(config)# no description
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-3
Configure Contact Information
Commands
contact text
no contact
Syntax Description
no
Remove configuration/delete entry/reset to default value
contact
Configure device contact information
text
The contact information of the device
Defaults
N/A
Command Modes
Global Configuration
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# contact "contact info"
moxa(config)# no contact
Error Messages
N/A
Related Commands
N/A
Show Location Information
Commands
location text
no location
Syntax Description
no
Remove configuration/delete entry/reset to default value
location
Configure the device location information
text
The location information of the device
Defaults
N/A
Command Modes
Global Configuration
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# location "location info"
moxa(config)# no location
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-4
Show System Information
Commands
show system information
Syntax Description
show
Display configuration/status information
system
Display system information
information
Display system information
Defaults
N/A
Command Modes
User EXEC
Privileged EXEC
Usage Guidelines
N/A
Examples
moxa# show system information
Hardware Version
Firmware Version
Device Contact
Device Name
Device Location
Device Description
Device Uptime
Login Authentication Mode
: V0.0.0
: v0.3 build 2019_050202111
:
: moxa
:
:
:0 Days, 1 Hrs, 35 Mins, 21 Secs
: Local
Error Messages
N/A
Related Commands
N/A
Firmware Upgrade
Upgrade the Firmware
Commands
copy { tftp_url | sftp_url> } device-firmware
Syntax Description
copy
Copy the target file or input
device-firmware
The system firmware
tftp_url
The address of the remote TFTP server in the format
"tftp://server/filename"
sftp_url
The address of the remote SFTP server in the format
"sftp://username:password@server/filename"
Defaults
N/A
Command Modes
Privileged EXEC
Usage Guidelines
N/A
Examples
copy tftp://192.168.127.2/FWR_TSN-G5000_v0.1_2019_0904_1452.rom
device-firmware
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-5
Configuration Backup and Restore
Copy Running Configuration
Commands
copy running-config { <tftp_url> | <sftp_url> }
copy { <tftp_url> | <sftp_url> } running-config
Syntax Description
copy
Copy the target file or input
running-config
The running configuration to be copied
tftp_url
The location of the file to be copied on the remote TFTP server
sftp_url
The location of the file to be copied on the remote SFTP server
Defaults
N/A
Command Modes
Privileged EXEC
Usage Guidelines
N/A
Examples
copy running-config tftp://192.168.127.2
copy tftp://192.168.127.2 running-config
Error Messages
N/A
Related Commands
N/A
Copy Startup Configuration
Commands
copy startup-config { <tftp_url> | <sftp_url>}
copy { <tftp_url> | <sftp_url>} startup-config
Syntax Description
copy
Copy the target file or input
startup-config
The startup configuration to be copied
tftp_url
The location of the file to be copied on the remote TFTP server
sftp_url
The location of the file to be copied on the remote SFTP server
Defaults
N/A
Command Modes
Privileged EXEC
Usage Guidelines
N/A
Examples
copy startup-config tftp://192.168.127.2
copy tftp://192.168.127.2 startup-config
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-6
Event Log Backup
Commands
copy event-log { <tftp_url> | <sftp_url> }
Syntax Description
copy
Copy the target file or input
event-log
The system event log to be copied
tftp_url
The address of the remote TFTP server in the format
"tftp://server/filename"
sftp_url
The address of the remote SFTP server in the format
"sftp://username:password@server/filename"
Defaults
N/A
Command Modes
Privileged EXEC
Usage Guidelines
N/A
Examples
copy event-log tftp://192.168.127.2
Error Messages
N/A
Related Commands
N/A
Account Management
User Account
Configure User Account Setting
Commands
username <username> password <passwd> group { admin | user | supervisor } status { enable | disable }
email <email>
no username username
Syntax Description
no
Remove configuration/delete entry/reset to default value
username
Configures username parameters
username
The username to be used for login
password
Configures password parameters
password
The password to be entered by the user
group
Configures the user privilege level
group
Valid values are "admin", "supervisor", and "user"
"admin" for admin group, "supervisor" for supervisor, and "user"
for normal user group
status
Configures user status parameters
enable
Enable the user
disable
Disable the user
email
Configures the user email
email
The user’s email address
Defaults
N/A.
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
(config)# username testuser password test123 group admin status enable email
Error Messages
% Max User Account Amount Reached
% Invalid Username Format
% Password doesn’t comply with password rules.
% Invalid Email Format
Moxa Command Line Interface Commands
3-7
% Invalid Password Format
% User does not exist
% At least one admin should be active.
% User status cannot be updated by self.
% User Deletion Failed
% User cannot be disabled by self
% User cannot be modified group by self
% User cannot be deleted by self
Related Commands
Show user
Show User Information
Commands
show user
Syntax Description
show
Display running information for the function
user
Display user parameters
Defaults
N/A
Command Modes
Global configuration/ User EXEC
Usage Guidelines
N/A
Examples
# show user
USER ACTIVE PRIVILEGE EMAIL
supervisor 1 supervisor supervisor@sample.com
Error Messages
N/A
Related Commands
username
Password Policy
Configure Password Maximum Lifetime
Commands
password max-life-time [<days (0-365)>]
Syntax Description
password
Configure password parameters
max-life-time
Configure the maximum lifetime of the password
days
Maximum lifetime in days; a 0 or “no” value means it does not
expire
Defaults
0
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
moxa# config
moxa(config)# password max-life-time 30
moxa(config)# password max-life-time
Error Messages
N/A
Related Commands
show password max-life-time
Moxa Command Line Interface Commands
3-8
Configure Password Validation Rules
Commands
password validate-rules [lowercase] [uppercase] [numbers] [symbols]
Syntax Description
password
Configure password parameters
validate-rules
Configure validation rules
lowercase
Configure at least 1 lowercase flag for password validation
uppercase
Configure at least 1 uppercase flag for password validation
numbers
Configure at least 1 numbers flag for password validation
symbols
Configure at least 1 symbols flag for password validation
Defaults
There are no validation rules configured by default
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
moxa# config
moxa(config)# password validate-rules lowercase numbers
moxa(config)# password validate-rules
Error Messages
N/A
Related Commands
show password validate-rules
Configure Password Minimum Length
Commands
password minimum-length <minimum-len (4-63)>
Syntax Description
password
Configure password parameters
minimum-length
Configure the minimum password length
minimum-len
The minimum password length
Defaults
4
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
moxa# config
moxa(config)# password minimum-length 8
Error Messages
N/A
Related Commands
show password minimum-length
Show Password Minimum Length
Commands
show minimum password minimum-length
Syntax Description
show
Display running information for the function
password
Display password parameters
minimum-length
Display the minimum length of the password
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
moxa# show password minimum-length 8
Error Messages
N/A
Related Commands
password minimum-length
Moxa Command Line Interface Commands
3-9
Show Password Validation Rules
Commands
show password validate-rules
Syntax Description
show
Display running information for the function
password
Display password parameters
validate-rules
Display the password validation rules
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
moxa# show password validate-rules
Error Messages
N/A
Related Commands
password validate-rules
Network
IP Configuration
Configure IP Management Address
Commands
ip management address { dhcp | ipv4-address ipv4-netmask [ ipv4-gateway ] }
Syntax Description
ip
Configure IP parameters
management
Configure IPv4 management address parameters
address
Configure the IPv4 management address of the device
dhcp
Assign the IPv4 address by DHCP
ipv4-address
The IPv4 address
ipv4-netmask
The IPv4 subnet mask
ipv4-gateway
The IPv4 gateway
Defaults
ipv4-address: 192.168.127.253
ipv4-netmask: 255.255.255.0
ipv4-gateway: 0.0.0.0
Command Modes
Global Configuration
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# ip management address dhcp
moxa(config)# ip management address 10.1.1.1 255.255.255.0 10.1.1.254
Error Messages
Invalid: Invalid IPv4 Management Address ipv4-address/ipv4-netmask.
Invalid: Gateway ipv4-gateway is not reachable.
Related Commands
N/A
Moxa Command Line Interface Commands
3-10
DHCP Server
Show IP DHCP
Commands
show ip dhcp [ { binding | static | port-based-ip-assignment } ]
Syntax Description
show
Display configuration/status information
ip
Display IP information
dhcp
Display DHCP server information
binding
Display binding information
static
Display MAC-based IP assignment information
port-based-ip-assignment
Display port-based IP assignment information
Defaults
N/A
Command Modes
User EXEC
Privileged EXEC
Usage Guidelines
N/A
Examples
moxa# show ip dhcp
DHCP Server Mode: DHCP / MAC-based IP Assignment
DHCP Pool List
----------------------------------------------
Index : 1
State : Enable
First IP Address : 192.168.127.10
Last IP Address : 192.168.127.20
Netmask : 255.255.255.0
Lease Time (secs) : 86400
Default Gateway :
NTP Server :
DNS Server 1 :
DNS Server 2 :
moxa# show ip dhcp binding
Host Name IP Address MAC Address Time Left
-------------------- --------------- ----------------- ----------------
VirtualBox 192.168.127.10 08:00:27:f6:bf:98 23 h: 59 m: 55 s
// A MAC-based IP assignment is created
moxa# show ip dhcp static
DHCP Server Mode: DHCP / MAC-based IP Assignment
MAC-based IP Assignment List
----------------------------------------------
Index : 1
State : Enable
Host Name : host1
Host IP Address : 192.168.127.30
Host Netmask : 255.255.255.0
MAC Address : 08:00:27:f6:bf:98
Lease Time (secs) : 86400
Default Gateway :
NTP Server :
DNS Server 1 :
DNS Server 2 :
Moxa Command Line Interface Commands
3-11
moxa# show ip dhcp binding
Host Name IP Address MAC Address Time Left
-------------------- --------------- ----------------- ----------------
host1 192.168.127.30 08:00:27:f6:bf:98 (static)
// A Port-based IP assignment is created
moxa# show ip dhcp port-based-ip-assignment
DHCP Server Mode: Port-based IP Assignment
Port-based IP Assignment List
----------------------------------------------
Port : 2
State : Enable
Static IP Address : 192.168.127.40
Host Netmask : 255.255.255.0
Lease Time (secs) : 86400
Default Gateway :
NTP Server :
DNS Server 1 :
DNS Server 2 :
moxa# show ip dhcp binding
Host Name IP Address MAC Address Time Left
-------------------- --------------- ----------------- ----------------
192.168.127.40 (static)
Error Messages
N/A
Related Commands
N/A
Configure/Disable DHCP Server Mode
Commands
dhcp-server mode disable
dhcp-server mode dhcp-and-mac-based-ip-assignment
dhcp-server mode port-based-ip-assignment
Syntax Description
dhcp-server
Configure DHCP server parameters
mode
Configure DHCP server mode parameters
disable
Disable the DHCP server
dhcp-and-mac-based-ip-
assignment
Standard DHCP server and MAC-based DHCP
port-based-ip-assignment
Port-based DHCP sever
Defaults
N/A
Command Modes
Privileged EXEC
Global Configuration
Usage Guidelines
N/A
Examples
Moxa(config)# dhcp-server mode disable
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-12
Enable/Disable IP DHCP Pool
Commands
ip dhcp pool <integer> [ { enable | disable } ]
Syntax Description
ip
Configure IP parameters
dhcp
Configure DHCP server parameters
pool
Configure address pool parameters
<integer>
Pool number
enable
Enable the address pool
disable
Disable the address pool
Defaults
N/A
Command Modes
Privileged EXEC
Global Configuration
Usage Guidelines
N/A
Examples
moxa(config)# ip dhcp pool 1 enable
moxa(dhcp-config)#
Error Messages
N/A
Related Commands
N/A
Remove IP DHCP Pool
Commands
no ip dhcp pool <integer>
Syntax Description
no
Remove configuration/delete entry/reset to default value
ip
Configure IP parameters
dhcp
Configure DHCP server parameters
pool
Configure address pool parameters
<integer>
The address pool number
Defaults
N/A
Command Modes
Privileged EXEC
Global Configuration
Usage Guidelines
N/A
Examples
moxa# no ip dhcp pool 1
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-13
Enable/Disable IP DHCP Static Pool
Commands
ip dhcp static pool <string (63)> [ { enable | disable } ]
Syntax Description
ip
Configure IP parameters
dhcp
Configure DHCP server parameters
static
Configure MAC-based IP assignment parameters
pool
Configure address pool parameters
<string (63)>
The client host name (DHCP option 12)
enable
Enable the address pool
disable
Disable the address pool
Defaults
N/A
Command Modes
Privileged EXEC
Global Configuration
Usage Guidelines
N/A
Examples
moxa(config)# ip dhcp static pool host1 enable
moxa(dhcp-config)#
Error Messages
N/A
Related Commands
N/A
Remove IP DHCP Static Pool
Commands
no ip dhcp static pool <string (63)>
Syntax Description
no
Remove configuration/delete entry/reset to default value
ip
Configure IP parameters
dhcp
Configure DHCP server parameters
static
Configure MAC-based IP assignment parameters
pool
Configure address pool parameters
string (63)
The client host name (DHCP option 12)
Defaults
N/A
Command Modes
Privileged EXEC
Global Configuration
Usage Guidelines
N/A
Examples
moxa(config)# no ip dhcp static pool host1
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-14
DHCP and MAC-based IP Assignment
Configure DHCP Server Pool
Commands
network <ucast_addr> <ucast_addr> <ip_mask>
Syntax Description
network
Configure network parameters
<ucast_addr>
The address pool starting IP address
<ucast_addr>
The address pool ending IP address
<ip_mask>
The subnet mask
Defaults
N/A
Command Modes
Privileged EXEC
DHCP Configuration
Usage Guidelines
N/A
Examples
moxa(dhcp-config)# network 192.168.127.10 192.168.127.20 255.255.255.0
Error Messages
N/A
Related Commands
N/A
Configure DHCP Server Host IP Address
Commands
host <ucast_addr> <ip_mask>
Syntax Description
host
Configure host parameters
<ucast_addr>
The unicast IP address
<ip_mask>
The subnet mask
Defaults
N/A
Command Modes
Privileged EXEC
DHCP Configuration
Usage Guidelines
N/A
Examples
moxa(dhcp-config)# host 192.168.127.100
Error Messages
N/A
Related Commands
N/A
Configure DHCP Server Host MAC Address
Commands
hardware-address <ucast_mac>
Syntax Description
hardware-address
Configure the MAC address
<ucast_mac>
The MAC address
Defaults
N/A
Command Modes
Privileged EXEC
DHCP Configuration
Usage Guidelines
N/A
Examples
moxa(dhcp-config)# hardware-address 00:90:e8:11:22:33
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-15
Configure Lease Time
Commands
lease <integer (10-604800)>
Syntax Description
lease
Configure the IP lease duration
<integer (10-604800)>
The IP lease duration in seconds
Defaults
N/A
Command Modes
Privileged EXEC
DHCP Configuration
Usage Guidelines
N/A
Examples
moxa(dhcp-config)# lease 3600
Error Messages
N/A
Related Commands
N/A
Reset Lease time
Commands
no lease
Syntax Description
no
Remove configuration/delete entry/reset to default value
lease
Configure the IP lease duration
Defaults
N/A
Command Modes
Privileged EXEC
DHCP Configuration
Usage Guidelines
N/A
Examples
moxa(dhcp-config)# no lease
Error Messages
N/A
Related Commands
N/A
Configure Default Router IP Address
Commands
default-router <ucast_addr>
Syntax Description
default-router
Configure the default router
<ucast_addr>
The unicast IP address
Defaults
N/A
Command Modes
Privileged EXEC
DHCP Configuration
Usage Guidelines
N/A
Examples
moxa(dhcp-config)# default-router 192.168.127.254
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-16
Remove Default Router IP Address
Commands
no default-router
Syntax Description
no
Remove configuration/delete entry/reset to default value
default-router
Configure the default router
Defaults
N/A
Command Modes
Privileged EXEC
DHCP Configuration
Usage Guidelines
N/A
Examples
moxa(dhcp-config)# no default-router
Error Messages
N/A
Related Commands
N/A
Configure DNS Server IP Address
Commands
dns-server <ucast_addr> [ <ucast_addr> ]
Syntax Description
dns-server
Configure the DNS server
<ucast_addr>
The unicast IP address
<ucast_addr>
The unicast IP address
Defaults
N/A
Command Modes
Privileged EXEC
DHCP Configuration
Usage Guidelines
N/A
Examples
moxa(dhcp-config)# dns-server 192.168.127.254
moxa(dhcp-config)# dns-server 192.168.127.251 192.168.127.252
Error Messages
N/A
Related Commands
N/A
Remove DNS Server IP Address
Commands
no dns-server
Syntax Description
no
Remove configuration/delete entry/reset to default value
dns-server
Configure the DNS server
Defaults
N/A
Command Modes
Privileged EXEC
DHCP Configuration
Usage Guidelines
N/A
Examples
moxa(dhcp-config)# no dns-server
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-17
Configure NTP Server IP Address
Commands
ntp-server <ucast_addr>
Syntax Description
ntp-server
Configure the NTP server
<ucast_addr>
The unicast IP address
Defaults
N/A
Command Modes
Privileged EXEC
DHCP Configuration
Usage Guidelines
N/A
Examples
moxa(dhcp-config)# ntp-server 192.168.127.254
Error Messages
N/A
Related Commands
N/A
Remove NPT Server IP Address
Commands
no ntp-server
Syntax Description
no
Remove configuration/delete entry/reset to default value
ntp-server
Configure the NTP server
Defaults
N/A
Command Modes
Privileged EXEC
DHCP Configuration
Usage Guidelines
N/A
Examples
moxa(dhcp-config)# no ntp-server
Error Messages
N/A
Related Commands
N/A
Configure Port-based IP Assignment
Commands
ip dhcp port-based-ip-assignment <ucast_addr> <ip_mask>
Syntax Description
ip
Configure IP parameters
dhcp
Configure DHCP server parameters
port-based-ip-assignment
Configure port-based IP assignment parameters
<ucast_addr>
The unicast IP address
<ip_mask>
The subnet mask
Defaults
N/A
Command Modes
Privileged EXEC
Interface Configuration
Usage Guidelines
N/A
Examples
moxa(config)# interface ethernet 1/2
moxa(config-if)# ip dhcp port-based-ip-assignment 192.168.127.100 255.255.255.0
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-18
Remove Port-based IP Assignment
Commands
no ip dhcp port-based-ip-assignment
Syntax Description
no
Remove configuration / delete entry / reset to
default value
ip
Configure IP parameters
dhcp
Configure DHCP server parameters
port-based-ip-assignment
Configure port-based IP assignment parameters
Defaults
N/A
Command Modes
Privileged EXEC
Interface Configuration
Usage Guidelines
N/A
Examples
moxa(config)# interface ethernet 1/2
moxa(config-if)# no ip dhcp port-based-ip-assignment
Error Messages
N/A
Related Commands
N/A
Enable/Disable Port-based IP Assignment
Commands
ip dhcp port-based-ip-assignment { enable | disable }
Syntax Description
ip
Configure IP parameters
dhcp
Configure DHCP server parameters
port-based-ip-assignment
Configure port-based IP assignment parameters
enable
Enable port-based IP assignment
disable
Disable port-based IP assignment
Defaults
N/A
Command Modes
Privileged EXEC
Interface Configuration
Usage Guidelines
N/A
Examples
moxa(config)# interface ethernet 1/2
moxa(config-if)# ip dhcp port-based-ip-assignment enable
moxa(config-if)# ip dhcp port-based-ip-assignment disable
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-19
Configure Port-based IP Assignment Parameters
Commands
ip dhcp port-based-ip-assignment { { lease <integer (10-604800)> } | { default-router <ucast_addr> }
| { dns-server <ucast_addr> [ <ucast_addr> ] } | { ntp-server <ucast_addr> } }
Syntax Description
ip
Configure IP parameters
dhcp
Configure DHCP server parameters
port-based-ip-assignment
Configure port-based IP assignment parameters
lease
Configure duration of lease
<integer (10-604800)>
The duration of the lease in seconds
default-router
Configure the default router
<ucast_addr>
The unicast IP address
dns-server
Configure the DNS server
<ucast_addr>
The primary DNS server IP address
<ucast_addr>
The secondary DNS server IP address
ntp-server
Configure the NTP server
<ucast_addr>
The unicast IP address
Defaults
N/A
Command Modes
Privileged EXEC
Interface Configuration
Usage Guidelines
N/A
Examples
moxa(config-if)# ip dhcp port-based-ip-assignment lease 3600
moxa(config-if)# ip dhcp port-based-ip-assignment default-router 192.168.127.254
moxa(config-if)# ip dhcp port-based-ip-assignment dns-server 192.168.127.254
moxa(config-if)# ip dhcp port-based-ip-assignment dns-server 192.168.127.251
192.168.127.252
moxa(config-if)# ip dhcp port-based-ip-assignment ntp-server 192.168.127.254
Error Messages
N/A
Related Commands
N/A
Remove Port-based IP Assignment Parameters
Commands
no ip dhcp port-based-ip-assignment { lease | default-router | dns-server | ntp-server }
Syntax Description
no
Remove configuration/delete entry/reset to default value
ip
Configure IP parameters
dhcp
Configure DHCP server parameters
port-based-ip-assignment
Configure port-based IP assignment parameters
lease
Configure the IP lease duration
default-router
Configure the default router
dns-server
Configure the DNS server
ntp-server
Configure the NTP server
Defaults
N/A
Command Modes
Privileged EXEC
Interface Configuration
Usage Guidelines
N/A
Examples
moxa(config-if)# no ip dhcp port-based-ip-assignment lease
moxa(config-if)# no ip dhcp port-based-ip-assignment default-router
moxa(config-if)# no ip dhcp port-based-ip-assignment dns-server
moxa(config-if)# no ip dhcp port-based-ip-assignment ntp-server
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-20
Time
Time Zone
Configure Clock Time Zone
Commands
clock timezone { "-12" | "-11" | "-10" | "-9:30" | "-9" | "-8" | "-7" | "-6" | "-5" | "-4" | "-3:30" | "-3" | "-2"
| "-1" | "0" | "1" | "2" | "3" | "3:30" | "4" | "4:30" | "5" | "5:30" | "5:45" | "6" | "6:30" | "7" | "8" | "8:30" | "8:45"
| "9" | "9:30" | "10" | "10:30" | "11" | "12" | "12:45" | "13" | "14" }
Syntax Description
clock
Configure system clock parameters
timezone
Configure the timezone
"-12"
UTC-12:00
"-11"
UTC-11:00
"-10"
UTC-10:00
"-9:30"
UTC-09:30
"-9"
UTC-09:00
"-8"
UTC-08:00
"-7"
UTC-07:00
"-6"
UTC-06:00
"-5"
UTC-05:00
"-4"
UTC-04:00
"-3:30"
UTC-03:30
"-3"
UTC-03:00
"-2"
UTC-02:00
"-1"
UTC-01:00
"0"
UTC+00:00
"1"
UTC+01:00
"2"
UTC+02:00
"3"
UTC+03:00
"3:30"
UTC+03:30
"4"
UTC+04:00
"4:30"
UTC+04:30
"5"
UTC+05:00
"5:30"
UTC+05:30
"5:45"
UTC+05:45
"6"
UTC+06:00
"6:30"
UTC+06:30
"7"
UTC+07:00
"8"
UTC+08:00
"8:30"
UTC+08:30
"8:45"
UTC+08:45
"9"
UTC+09:00
"9:30"
UTC+09:30
"10"
UTC+10:00
"10:30"
UTC+10:30
"11"
UTC+11:00
"12"
UTC+12:00
"12:45"
UTC+12:45
"13"
UTC+13:00
Moxa Command Line Interface Commands
3-21
"14"
UTC+14:00
Defaults
N/A
Command Modes
Global Configuration
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# clock timezone "8"
Error Messages
N/A
Related Commands
N/A
System Time
Configure Clock Source
Commands
clock source { local | ntp | sntp }
Syntax Description
clock
Configure system clock parameters
source
Configure the source of the system clock
local
Use the local clock
ntp
Use Network Time Protocol (NTP)
sntp
Use Simple Network Time Protocol (SNTP)
Defaults
clock source: local
Command Modes
Global Configuration
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# clock source local
Error Messages
N/A
Related Commands
N/A
Configure Clock Setting
Commands
clock set hh:mm:ss [ month ] [ day ] [ year ]
Syntax Description
clock
Configure system clock parameters
set
Configure the system time
hh:mm:ss
The system time in the format hh:mm:ss
month
The month, January (1) to December (12)
day
The day of the month (1 to 31)
year
The year
Defaults
N/A
Command Modes
Global Configuration
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# clock set 11:11:11 12 31 2019
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-22
Enable Clock Summer Time
Commands
clock summer-time enable
Syntax Description
clock
Configure system clock parameters
summer-time
Configure Daylight Savings Time parameters
enable
Enable Daylight Savings Time
Defaults
Daylight saving time is disabled by default
Command Modes
Global Configuration
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# clock summer-time enable
Error Messages
Invalid: The start date plus offset should before the end date.
Related Commands
N/A
Disable Clock Summertime
Commands
clock summer-time disable
Syntax Description
clock
Configure system clock parameters
summer-time
Configure Daylight Savings Time parameters
disable
Disable Daylight Savings Time
Defaults
Daylight saving time is disabled by default
Command Modes
Privileged EXEC
Global Configuration
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# clock summer-time disable
Error Messages
N/A
Related Commands
N/A
Configure Clock Summertime Start Date
Commands
clock summer-time start-date [ month ] [ day ] [ year ] [hour minute hh:mm:ss ]
Syntax Description
clock
Configure system clock parameters
summer-time
Configure Daylight Savings Time parameters
start-date
Configure the start date of Daylight Saving Time
month
The month, January (1) to December (12)
day
The day of the month (1 to 31)
year
The year
hour
The hour
minute
The minutes
Defaults
The daylight saving time start date is set to Jan 01 2000 00:00
Command Modes
Global Configuration
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# clock summer-time start-date 1 1 2019 23 30
Error Messages
Invalid: Start date is invalid.
Invalid: The start date plus offset should before the end date.
Related Commands
N/A
Moxa Command Line Interface Commands
3-23
Configure Clock Summertime End Date
Commands
clock summer-time start-date month day year hour minute
Syntax Description
clock
Configure system clock parameters
summer-time
Configure Daylight Savings Time parameters
end-date
Configure the end date of Daylight Savings Time
month
The month, January (1) to December (12)
day
The day of the month (1 to 31)
year
The year
hour
The hour
minute
The minutes
Defaults
The daylight saving time end date is set to Dec 31 2000 23:00
Command Modes
Global Configuration
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# clock summer-time end-date 7 31 2019 23 30
Error Messages
Invalid: End date is invalid
Invalid: The start date plus offset should before the end date.
Related Commands
N/A
Configure Clock Summertime Offset
Commands
clock summer-time offset offset-hour [ offset-minute ]
Syntax Description
clock
Configure system clock parameters
summer-time
Configure Daylight Savings Time parameters
offset
Configure the offset of Daylight Saving Time
offset-hour
The time offset hours
offset-minute
The time offset minutes
Defaults
daylight saving time offset: 0 Hour 0 Minutes
Command Modes
Global Configuration
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# clock summer-time offset 1 30
Error Messages
Invalid: The start date plus offset should before the end date.
Related Commands
N/A
Moxa Command Line Interface Commands
3-24
Configure NTP Authentication Key
Commands
ntp authentication-key key-index key-id md5 key-string
no ntp authentication-key key-index
Syntax Description
no
Remove configuration/delete entry/reset to default value
ntp
Configure NTP/SNTP parameters
authentication-key
Configure the NTP authentication key
key-index
The index of the key, ranging from 1 to 10
key-id
The key ID, ranging from 1 to 65535
md5
Use MD5 authentication
key-string
The authentication key with a maximum length of 32 characters
for plain text, 66 characters for Moxa-encrypted hex
Defaults
N/A
Command Modes
Global Configuration
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# ntp authentication-key 1 1 md5 1a2b3c4d
moxa(config)# no ntp authentication-key 1
Error Messages
Invalid: Authentication key ID key-id is duplicated.
Related Commands
N/A
Configure NTP Remote Server
Commands
ntp remote-server ntp server-index server-address [ authentication key key-id ]
no ntp remote-server ntp server-index [ authentication ]
Syntax Description
no
Remove configuration/delete entry/reset to default value
ntp
Configure NTP/SNTP parameters
remote-server
Configure remote time server parameters
ntp
Configure NTP server parameters
server-index
The index of the server, ranging from 1 to 2
server-address
The NTP server address
authentication
Configure NTP authentication parameters
key
Use key authentication
key-id
The ID of the authentication key
Defaults
NTP time server: time.nist.gov
Command Modes
Global Configuration
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# ntp remote-server ntp 1 1.1.1.1
moxa(config)# ntp remote-server ntp 2 2.2.2.2 authentication key 1
moxa(config)# no ntp remote-server ntp 2 authentication
moxa(config)# no ntp remote-server ntp 1
Error Messages
Invalid: Authentication key ID key-id of NTP client server-index does not exist.
Related Commands
N/A
Moxa Command Line Interface Commands
3-25
Configure SNTP Remote Server
Commands
ntp remote-server sntp server-index server-address
no ntp remote-server sntp server-index server-address
Syntax Description
no
Remove configuration/delete entry/reset to default value
ntp
Configure NTP/SNTP parameters
remote-server
Configure remote time server parameters
sntp
Configure SNTP server parameters
server-index
The index of the server, ranging from 1 to 2
server-address
The SNTP server address
Defaults
The default SNTP time server is set to time.nist.gov
Command Modes
Global Configuration
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# ntp remote-server sntp 1 1.1.1.1
moxa(config)# no ntp remote-server sntp 1
Error Messages
N/A
Related Commands
N/A
Enable NTP Server
Commands
ntp server enable
Syntax Description
ntp
Configure NTP/SNTP parameters
server
Configure NTP server parameters
enable
Enable the NTP server
Defaults
NTP server: disable
Command Modes
Global Configuration
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# ntp server enable
Error Messages
N/A
Related Commands
N/A
Disable NTP Server
Commands
ntp server disable
Syntax Description
ntp
Configure NTP/SNTP parameters
server
Configure NTP server parameters
disable
Disable the NTP server
Defaults
The NTP server is disabled by default
Command Modes
Global Configuration
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# ntp server disable
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-26
Configure NTP Server Authentication
Commands
ntp server authentication
Syntax Description
ntp
Configure NTP/SNTP parameters
server
Configure NTP server parameters
authentication
Enable authentication
Defaults
NTP server authentication is disabled by default
Command Modes
Global Configuration
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# ntp server authentication
Error Messages
N/A
Related Commands
N/A
Disable NTP Server Authentication
Commands
no ntp server authentication
Syntax Description
no
Remove configuration/delete entry/reset to default value
ntp
Configure NTP/SNTP parameters
server
Configure NTP server parameters
authentication
NTP authentication
Defaults
NTP server authentication is disabled by default
Command Modes
Global Configuration
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# no ntp server authentication
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-27
Show Clock Information
Commands
show clock
Syntax Description
show
Display configuration/status information
clock
Display system clock information
Defaults
N/A
Command Modes
User EXEC
Privileged EXEC
Usage Guidelines
N/A
Examples
moxa# show clock
Clock Source : Local
Time Zone : UTC+00:00
Current Time : Fri May 03 22:59:33 2019
Daylight Saving : Disabled
Start Date : Jan 01 2000 00:00
End Date : Dec 31 2000 23:00
Offset : 0 Minutes
Authentication Keys
NTP Client Time Server
[1] time.nist.gov (No Auth)
SNTP Client Time Server
[1] time.nist.gov
NTP/SNTP Server : Disabled
Authentication : Disabled
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-28
Port
Port Interface
Port Setting
Show Interface Status
Commands
show interface status
Syntax Description
show
Show running system information
interface
Display interface information
status
The status of the interface
Defaults
N/A
Command Modes
Privileged EXEC
Usage Guidelines
N/A
Examples
moxa# show interface status
Port Status Duplex Speed Negotiation MDI/MDIX
---- ------ ------ ----- ----------- ----------
Eth1/1 connected Full 1 Gbps Auto MDIX(Auto)
Eth1/2 connected Full 1 Gbps Auto MDIX(Auto)
Eth1/3 not connected Half - Auto -
Eth1/4 not connected Half - Auto -
Eth2/1 not present - - - -
Eth2/2 not present - - - -
Eth2/3 not present - - - -
Eth2/4 not present - - - -
Eth3/1 not connected Half - Auto -
Eth3/2 not connected Half - Auto -
Eth3/3 not connected Half - Auto -
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-29
Show Interface Type and ID
Commands
show interfaces [<interface-type> <interface-id> ]
show interfaces [{ [<interface-type> <interface-id>] [{ description | storm-control | flowcontrol |
status }] }]
Syntax Description
show
Display configuration/statistics/general
interfaces
Display interface information
interface-type
The Ethernet type
interface-id
The slot number/port number
description
Description about the interface
storm-control
Broadcast, multicast, and unicast storm control suppression levels
for an interface
flowcontrol
Receive or send flow control value for an interface
status
The status of the interface
Defaults
N/A
Command Modes
Privileged EXEC
Usage Guidelines
N/A
Examples
moxa# show interfaces ethernet 1/1
Eth1/1 up, line protocol is down (not connect)
Bridge Port Type: Customer Bridge Port
Interface SubType: gigabitEthernet
Interface Alias: Slot1/1
Media Type: 1000TX,RJ45,PTP
Hardware Address is 00:00:00:00:00:05
MTU 1522 bytes, Half duplex, 1 Gbps, Auto-Negotiation
HOL Block Prevention enabled.
CPU Controlled Learning disabled.
Auto-MDIX invalid
Input flow-control is off,output flow-control is off
Port State: Discarding
Link Up/Down Trap is enabled
Reception Counters
Octets : 0
Unicast Packets : 0
Multicast Packets : 0
Octets : 0
Unicast Packets : 0
Multicast Packets : 0
Broadcast Packets : 0
Discarded Packets : 0
Error Packets : 0
Unknown Protocol : 0
CRC Errors : 0
Symbol Errors : 0
Good CRC Frame Size Errors: 0
Oversized w/ Bad CRC : 0
Moxa Command Line Interface Commands
3-30
Transmission Counters
Octets : 0
Unicast Packets : 0
Multicast Packets : 0
Broadcast Packets : 0
Discarded Packets : 0
Error Packets : 0
Bad CRC : 0
Error Drops : 0
Timeout Drops : 0
Error Packets : 0
Error Messages
N/A
Related Commands
N/A
Show Interface Description
Commands
show interface description
Syntax Description
show
Display configuration/statistics/general information
interface
Display interface information
description
Description about the interface
Defaults
N/A
Command Modes
Privileged EXEC
Usage Guidelines
N/A
Examples
moxa# show interfaces description
Interface AdminStatus OperProtocol Description
--------- ----------- ------------ -----------
Eth1/1 up down
Eth1/2 up down
Eth1/3 up down
Eth1/4 up down
Eth2/1 up down
Eth2/2 up down
Eth2/3 up down
Eth2/4 up down
Eth3/1 up down
Eth3/2 up down
Eth3/3 up down
Eth3/4 up down
Eth4/1 up down
Eth4/2 up down
Eth4/3 up down
Eth4/4 up down
Eth5/1 up down
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-31
Show Flow Control
Commands
show flow-control [ interface [{ port-channel <port-channel-id>| ethernet <slot>/<port> }] ]
Syntax Description
show
Display configuration/statistics/general information
flow-control
Display flow-control information
interface
Protocol-specific configuration of the interface
port-channel
The port channel interface
port-channel-id
The port channel ID
interface-type
The Ethernet interface
slot/port
The slot number or port number
Defaults
N/A
Command Modes
Privileged EXEC
Usage Guidelines
N/A
Examples
moxa# show flow-control
Port Admin Oper Tx Pause Rx Pause HC TxPause HC RxPause
---- ------- ------- -------- -------- ---------- ----------
Eth1/1 off off 0 0 0 0
Eth1/2 off off 0 0 0 0
Eth1/3 off off 0 0 0 0
Eth1/4 off off 0 0 0 0
Eth2/1 off off 0 0 0 0
Eth2/2 off off 0 0 0 0
Eth2/3 off off 0 0 0 0
Eth2/4 off off 0 0 0 0
Eth3/1 off off 0 0 0 0
Eth3/2 off off 0 0 0 0
Eth3/3 off off 0 0 0 0
Eth3/4 off off 0 0 0 0
Eth4/1 off off 0 0 0 0
Eth4/2 off off 0 0 0 0
Eth4/3 off off 0 0 0 0
Eth4/4 off off 0 0 0 0
Eth5/1 off off 0 0 0 0
Eth5/2 off off 0 0 0 0
Eth5/3 off off 0 0 0 0
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-32
Show Linkup Delay Status
Commands
show linkup-delay
show linkup-delay [ interface <iftype> <ifnum> ]
Syntax Description
show
Display configuration/statistics/general
linkup-delay
Display linkup-delay information
interface
Interface-related configuration
iftype
The Ethernet type
ifnum
The slot number or port number
Defaults
N/A
Command Modes
Privileged EXEC
Usage Guidelines
N/A
Examples
moxa# show linkup-delay
LinkUp Delay Table
--------------------
Interface Id : Eth1/1
Link Up Delay System Status : DISABLED
Link Up Delay Port Status : DISABLED
Link Up Delay Port Time : 2 Seconds
Link Up Delay Remaining Time : 0 Seconds
LinkUp Delay Table
--------------------
Interface Id : Eth1/2
Link Up Delay System Status : DISABLED
Link Up Delay Port Status : DISABLED
Link Up Delay Port Time : 2 Seconds
Link Up Delay Remaining Time : 0 Seconds
Error Messages
N/A
Related Commands
N/A
Configure Shutdown Settings
Commands
shutdown
no shutdown
Syntax Description
no
Remove configuration/delete entry/reset to default value
shutdown
Configure shutdown parameters
Defaults
Physical ports are enabled by default
Command Modes
Interface Configuration
Usage Guidelines
N/A
Examples
moxa(config-if)# shutdown
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-33
Configure Description Settings
Commands
description <description of this interface>
no description
Syntax Description
no
Remove configuration/delete entry/reset to default value
description
Configure description parameters
description of this interface
The description of the interface
Defaults
Empty string
Command Modes
Interface Configuration
Usage Guidelines
N/A
Examples
moxa(config-if)# description moxa
Error Messages
% Port Setting: Invalid: data.portTable[0].description must be shorter than or equal to
127 characters
Related Commands
N/A
Configure Duplex Settings
Commands
duplex { full | half }
Syntax Description
duplex
Configure duplex parameters
full
Set the port to full-duplex mode
half
Set the port to half-duplex mode
Defaults
The port is full-duplex without auto-negotation by default
Command Modes
Interface Configuration
Usage Guidelines
N/A
Examples
moxa(config-if)# no auto-negotiation
moxa(config-if)# duplex full
Error Messages
% Port Setting: Invalid: Fiber port can only be configured to full duplex/auto-mdix.
% Port Setting: Invalid: Speed, Duplex and MDI/MDIX can only be configured when the
port exists.
Related Commands
speed { 10 | 100 }
Configure Speed Settings
Commands
speed { 10 | 100 }
Syntax Description
speed
Configure port speed parameters
10
Set the port to run at 10 Mbps
100
Set the port to run at 100 Mbps
Defaults
The port is set to 100 Mbps by default if auto-negotiation is disabled on the port
Command Modes
Interface Configuration
Usage Guidelines
N/A
Examples
moxa(config-if)# no auto-negotiation
moxa(config-if)# speed 100
Error Messages
% Port Setting: Invalid: Speed cannot configure a speed which is over the ability of the
port.
% Port Setting: Invalid: If a speed is equal to or faster than 10G, the port cannot
configure autoNego/duplex/speed.
% Port Setting: Invalid: Speed, Duplex and MDI/MDIX can only be configured when the
port exists.
Related Commands
duplex { full | half }
Moxa Command Line Interface Commands
3-34
Enable/Disable Flow Control Setting
Commands
flowcontrol { on | off }
Syntax Description
flowcontrol
Configure flow-control parameters
on
Enable flow control
off
Disable flow control
Defaults
Flow control is disabled by default
Command Modes
Interface Configuration
Usage Guidelines
N/A
Examples
moxa(config-if)# flowcontrol off
Error Messages
N/A
Related Commands
N/A
Configure MDIx Setting
Commands
mdix { auto | mdi | mdix }
Syntax Description
mdix
Configure MDI/MDIX parameters
auto
Set the port as an auto-crossover port
mdi
Set the port as an MDI port
mdix
Set the port as an MDIX port
Defaults
Auto-crossover is enabled by default
Command Modes
Interface Configuration
Usage Guidelines
N/A
Examples
moxa(config-if)# mdix auto
Error Messages
% Port Setting: Invalid: Fiber port can only be configured to full duplex/auto-mdix.
% Port Setting: Invalid: Speed, Duplex and MDI/MDIX can only be configured when the
port exists.
Related Commands
N/A
Linkup Delay
Enable/Disable Linkup Delay
Commands
linkup-delay { enable | disable }
no linkup-delay
Syntax Description
no
Remove configuration/delete entry/reset to default value
linkup-delay
Configure linkup-delay parameters
enable
Enable linkup-delay in the system
disable
Disable linkup-delay in the system
Defaults
System-wide linkup-delay is disabled by default
Command Modes
Global Configuration
Usage Guidelines
N/A
Examples
moxa(config)# linkup-delay disable
Error Messages
N/A
Related Commands
linkup-delay
linkup-delay timer <integer (1-1000)>
Moxa Command Line Interface Commands
3-35
Configure Linkup Delay Timer
Commands
linkup-delay timer <integer (1-1000)>
Syntax Description
linkup-delay
Configure linkup-delay parameters
timer
Set the timer for linkup-delay
integer (1-1000)
Timer value ranger from 1 to 1000 seconds
Defaults
The linkup delay timer is 2 seconds by default
Command Modes
Interface Configuration
Usage Guidelines
N/A
Examples
moxa(config-if)# linkup-delay timer 2
Error Messages
N/A
Related Commands
linkup-delay [ enable | disable ]
linkup-delay
Configure Auto-Negotiation Setting
Commands
auto-negotiation
no auto-negotiation
Syntax Description
no
Remove configuration/delete entry/reset to default value
auto-negotiation
Configure auto-negotiation parameters
Defaults
Auto-negotiation is enabled by default
Command Modes
Interface Configuration
Usage Guidelines
N/A
Examples
moxa(config-if)# auto-negotiation
Error Messages
N/A
Related Commands
speed { 10 | 100 }
duplex { full | half }
Moxa Command Line Interface Commands
3-36
Link Aggregation
Port Channel
Configure Interface Port Channel
Commands
interface port-channel <port-channel-id>
no interface port-channel [<port-channel-id>]
Syntax Description
no
Remove configuration/delete entry/reset to default value
interface
Configure interface parameters
port-channel
The port-channel interface
port-channel-id
Configure port-channel ID parameters
Defaults
N/A
Command Modes
Global Configuration Mode
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# interface port-channel 10
moxa(config-if)# no shutdown
moxa(config-if)# exit
moxa(config)# no interface port-channel 10
Error Messages
'Invalid: Link Aggregation/Port-Channel group is out of range.'
'Invalid: Port channel should be activated before setting the selection policy
configuration.'
'Invalid: The port-channel does not exist.'
Related Commands
show port-channel load-balance
Configure Port Channel Shutdown Settings
Commands
shutdown
no shutdown
Syntax Description
no
Remove configuration/delete entry/reset to default value
shutdown
Shut down the port-channel
Defaults
N/A
Command Modes
port channel Interface Mode
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# interface port-channel 10
moxa(config-if)# no shutdown
moxa(config-if)# shutdown
Error Messages
N/A
Related Commands
show port-channel port
Moxa Command Line Interface Commands
3-37
Configure Port Channel Load Balance
Commands
port-channel load-balance { src-mac | dest-mac | src-dest-mac } [ <port-channel-id>]
no port-channel load-balance [<port-channel-id>]
Syntax Description
no
Remove configuration/delete entry/reset to default value
port-channel
Configure port-channel parameters
load-balance
Configure load balancing policy parameters
src-mac
Load distribution is based on the source MAC address
dest-mac
Load distribution is based on the destination MAC address
src-dest-mac
Load distribution is based on the source and destination MAC
address
<port-channel-id>
Configure port-channel ID parameters
Defaults
Port-channel load balancing is set to source/destination MAC address (src-dest-mac) by
default
Command Modes
Global Configuration
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# interface port-channel 10
moxa(config-if)# no shutdown
moxa(config-if)# exit
moxa(config-if)# port-channel load-balance src-mac 10
moxa(config-if)# no port-channel load-balance src-mac 10
Error Messages
'Invalid: Link Aggregation/Port-Channel group is out of range.'
'Invalid: Port channel should be activated before setting the selection policy
configuration.'
'Invalid: The port-channel does not exist.'
Related Commands
show port-channel load-balance
Moxa Command Line Interface Commands
3-38
Configure Channel Group Mode
Commands
channel-group <port-channel-id> mode { on | active | passive }
no channel-group
Syntax Description
no
Remove configuration/delete entry/reset to default value
channel-group
Configure port-channel parameters
port-channel-id
Configure channel group number parameters
mode
Configure mode for port-channel parameters
on
Configure the interface to use static trunk channel without LACP
active
Configure LACP negotiation to start unconditionally
passive
Configure LACP negotiation to start only when a LACP packet is
received from the peer
Defaults
N/A
Command Modes
Interface Configuration Mode
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# interface ethernet 1/1
moxa(config-if)# channel-group 10 mode on
moxa(config-if)# channel-group 10 mode active
moxa(config-if)# channel-group 10 mode passive
moxa(config-if)# no channel-group
Error Messages
'Invalid: Switch shall have at least 2 ports.'
'Invalid: This port cannot join as it exceeds the maximum number of port channels.'
'Invalid: Interface index duplication.'
'Invalid: Link Aggregation/Port-Channel group is out of range.'
'Invalid: When a port joins the port channel, the Interface Duplexity should be Full
Duplex.'
'Invalid: Port-channel cannot be created when flow control on the port is enabled.'
'Invalid: This port-channel is used by Turbo Ring/Turbo Chain/Dual Homing, it could not
be destroyed.'
'Invalid: The port-channel does not exist.'
'Invalid: In the same port-channel, the member port mode should be the same.'
'Invalid: Port-channel cannot be created when ports are operating at different speeds.'
Related Commands
show port-channel [<channel-group-ID>] {detail | load-balance | port | port-channel |
summary | protocol }
show interface [<interface-type> <interface-id> ] port-channel
Moxa Command Line Interface Commands
3-39
Configure LACP Wait Time
Commands
lacp wait-time < wait-time-value >
no lacp wait-time
Syntax Description
no
Remove configuration/delete entry/reset to default value
lacp
Configure LACP parameters
wait-time
Configure LACP wait-time parameters
wait-time-value
Configure the LACP wait-time value
Defaults
The default wait time is 2 seconds
Command Modes
Interface Configuration Mode
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# interface ethernet 1/1
moxa(config-if)# lacp wait-time 5
moxa(config-if)#no lacp wait-time
moxa(config-if)# end
Error Messages
N/A
Related Commands
N/A
Configure LACP Timeout Settings
Commands
lacp timeout { long | short }
no lacp timeout
Syntax Description
no
Remove configuration/delete entry/reset to default value
lacp
Configure LACP parameters
timeout
Configure timeout parameters
long
Configure the longest timeout of 90 seconds
short
Configure the shortest timeout of 3 seconds
Defaults
LACP timeout is set to long be default
Command Modes
Interface Configuration Mode
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# interface ethernet 1/1
moxa(config-if)# lacp timeout short
moxa(config-if)#no lacp timeout
moxa(config-if)# end
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-40
Show Link Aggregation Information
Commands
show port-channel [<port-channel-id>] [{ detail | load-balance | port | port-channel | summary |
protocol }]
Syntax Description
show
Display configuration / status information
port-channel
Display port-channel information
port-channel-id
Display channel group information
detail
Display detailed information
load-balance
Display load-balance scheme among ports in the port-channel
port
Display port-channel port information
port-channel
Display port-channel information
summary
Display summary per channel group
protocol
Display protocol used in the port-channel
Defaults
N/A
Command Modes
User EXEC
Privileged EXEC
Usage Guidelines
N/A
Examples
moxa# show port-channel 10 detail
moxa# show port-channel 10 load-balance
moxa# show port-channel 10 port
moxa# show port-channel 10 port-channel
moxa# show port-channel 10 summary
moxa# show port-channel
Error Messages
'Invalid: The port-channel does not exist.'
Related Commands
interface port-channel
channel-group <channel-group-id> mode { on |active | passive}
Show Port Channel Interfaces
Commands
show interfaces { [ { <interface-type> <interface-id > } ] port-channel }
Syntax Description
show
Display configuration / status information
interfaces
Display interface specific information
interface-type
Display interface type
interface-id
Display interface id
port-channel
Display port-channel information
Defaults
N/A
Command Modes
User EXEC
Privileged EXEC
Usage Guidelines
N/A
Examples
moxa# show interfaces ethernet 0/1 port-channel
Error Messages
N/A
Related Commands
channel-group <channel-group-id> mode { on |active | passive}
show port-channel [<port-channel-id>] [{ detail | load-balance | port | port-channel |
summary | protocol } ]
Moxa Command Line Interface Commands
3-41
PoE
PoE General Settings
Enable/Disable PoE Output Setting
Commands
poe { enable | disable }
Syntax Description
poe
Configure PoE parameters
enable
Enable PoE on the switch
disable
Disable PoE on the switch
Defaults
PoE is enabled by default
Command Modes
Privileged EXEC
Global Configuration
Usage Guidelines
Enable global power output.
Examples
moxa(config)# poe {enable | disable}
Error Messages
N/A
Related Commands
show poe [interface <iftype> <ifnum>] {config | status | diagnosis}
Configure Power Budget Setting
Commands
poe system-power-budget <watt: integer(30-720)>
Syntax Description
poe
Configure PoE parameters
system-power-budget
The total power budget for all PDs connected to the switch
watt: integer r(30-720)
Set the power budget depending on the external power
supply’s (EPS) output ability
Defaults
The default power budget is set to 720 watts
Command Modes
Privileged EXEC
Global Configuration
Usage Guidelines
Data range:
watt: 30-720
Examples
moxa(config)# poe system-power-budget <watt: integer(30-720)>
Error Messages
'Invalid: Sum of power allocation cannot exceed system power budget.'
Related Commands
show poe [interface <iftype> <ifnum>] {config | status | diagnosis}
Moxa Command Line Interface Commands
3-42
Configure Auto Power Cutting Settings
Commands
poe auto-power-cutting
no poe auto-power-cutting
Syntax Description
no
Remove configuration/delete entry/reset to default value
poe
Configure PoE parameters
auto-power-cutting
Cut power automatically when the PoE power consumption
exceeds the system power budget
Defaults
PoE automatic power cutting is disabled by default
Command Modes
Privileged EXEC
Global Configuration
Usage Guidelines
Enable auto-power-cutting to ensure the power supply for higher priority PDs
Examples
moxa(config)# poe auto-power-cutting
moxa(config)# no poe auto-power-cutting
Error Messages
N/A
Related Commands
show poe [interface <iftype> <ifnum>] {config | status | diagnosis}
poe priority {critical | high | low}
Moxa Command Line Interface Commands
3-43
PD Failure Check
Configure Port PD Failure Check Setting
Commands
poe pd-failure-check [ { device-ip <ucast_addr> | check-frequency <seconds: integer(5-300)> |
no-response-times <times: integer(1-10)> | action { no-action | restart-pd | shutdown-pd } } ]
no poe pd-failure-check
Syntax Description
no
Remove configuration/delete entry/reset to default value
poe
Configure PoE parameters
pd-failure-check
Check the PD fail status
device-ip
Check the device IP
ucast_addr
The device IP address
check-frequency
Check device frequency
seconds: integer (5-300)
The check frequency in seconds
no-response-times
The limit for the amount of no response checks the switch
performs
times: integer (1-10)
The amount of checks
action
Trigger an action if the no response times reaches the set
limit
no-action
Perform no action
restart-pd
Restart the PD
shutdown-pd
Shutdown the PD
Defaults
device-ip: 0.0.0.0
seconds: 10
times: 3
action: no-action
Data range:
seconds: 5-300
times: 1-10
Command Modes
Privileged EXEC
Interface Configuration
Usage Guidelines
Set PoE PD Failure Check on ports. The switch pings device-ip every check-frequency
second(s). The Action will be triggered if the no response times of ping reach
no-response-times.
Examples
moxa(config-if)# poe pd-failure-check [{device-ip <ucast_addr> | check-frequency
<integer(5-300)> | no-response-times <integer(1-10)> | action {no-action | restart-pd
| shutdown-pd}}]
moxa(config-if)# no poe pd-failure-check
Error Messages
'Invalid: Device IP is not a valid IP address.'
Related Commands
show poe pd-failure-check
Moxa Command Line Interface Commands
3-44
PoE Scheduling
Configure Scheduling Rule Setting
Commands
poe scheduling <rule-name: string(63)> <start-date-year: integer(1970-2038)> <start-date-month:
integer(1-12)> <start-date-day: integer(1-31)> <start-time-hour: integer(0-24)> <start-time-min:
integer(0-59)> <end-time-hour: integer(0-24)> <end-time-min: integer(0-59)>
Syntax Description
poe
Configure PoE parameters
scheduling
Schedule PoE availability with rules
rule-name: string (63)
The scheduling rule name
start-date-year: integer (1970-2038)
The scheduling rule starting year
start-date-month: integer (1-12)
The scheduling rule starting month
start-date-day: integer (1-31)
The scheduling rule starting day
start-time-hour: integer (0-24)
The scheduling rule starting hour
start-time-min: integer (0-59)
The scheduling rule starting minute
end-time-hour: integer (0-24)
The scheduling rule ending hour
end-time-min: integer (0-59)
The scheduling rule ending minute
Defaults
N/A
Command Modes
Privileged EXEC
Global Configuration
Usage Guidelines
Add a scheduling rule or modify rule times of an existing rule. By default, a new rule is
not activate and is non-repeating. Rules need to be applied to ports.
Examples
moxa(config)# poe scheduling <rule-name: string(63)> <start-date-year:
integer(1970-2038)> <start-date-month: integer(1-12)> <start-date-day:
integer(1-31)> <start-time-hour: integer(0-24)> <start-time-min: integer(0-59)>
<end-time-hour: integer(0-24)> <end-time-min: integer(0-59)>
Error Messages
'Invalid: Schedule is not valid.'
'Invalid: Start Date is not valid.'
'Invalid: Start Time is not valid.'
'Invalid: End Time is not valid.'
'Invalid: The start time cannot exceed the end time.'
'Invalid: Schedule is conflict.'
Related Commands
show poe scheduling [<rule-name: string(63)>]
no poe scheduling <rule-name: string(63)>
poe scheduling <rule-name: string(63)> activate
no poe scheduling <rule-name: string(63)> activate
poe scheduling <rule-name: string(63)> repeat {daily | weekday | weekend | sunday |
monday | tuesday | wednesday | thursday | friday | saturday}
no poe scheduling <rule-name: string(63)> repeat {daily | weekday | weekend | sunday
| monday | tuesday | wednesday | thursday | friday | saturday}
poe scheduling <rule-name: string(63)>
no poe scheduling <rule-name: string(63)>
Moxa Command Line Interface Commands
3-45
Apply Port Scheduling Rule
Commands
poe scheduling <rule-name: string (63)>
no poe scheduling <rule-name: string (63)>
Syntax Description
no
Remove configuration/delete entry/reset to default value
poe
Configure PoE parameters
scheduling
Schedule PoE with rules
rule-name:
string(63)
The scheduling rule name as the index key
Defaults
Scheduling rules are not applied to ports by default
Command Modes
Privileged EXEC
Interface Configuration
Usage Guidelines
Apply PoE scheduling rules to ports.
Examples
moxa(config-if)# poe scheduling <rule-name: string (63)>
moxa(config-if)# no poe scheduling <rule-name: string (63)>
Error Messages
N/A
Related Commands
show poe scheduling [<rule-name: string (63)>]
Remove PoE Schedule Setting
Commands
no poe scheduling <rule-name: string (63)>
Syntax Description
no
Remove configuration/delete entry/reset to default value
poe
Configure PoE parameters
scheduling
Schedule PoE with rules
rule-name: string (63)
The scheduling rule name as the index key
Defaults
N/A
Command Modes
Privileged EXEC
Global Configuration
Usage Guidelines
Delete a scheduling rule.
Examples
moxa(config)# no poe scheduling <rule-name: string(63)>
Error Messages
N/A
Related Commands
show poe scheduling [<rule-name: string(63)>]
poe scheduling <rule-name: string(63)> <start-date-year: integer(1970-2038)>
<start-date-month: integer(1-12)> <start-date-day: integer(1-31)> <start-time-hour:
integer(0-24)> <start-time-min: integer(0-59)> <end-time-hour: integer(0-24)>
<end-time-min: integer(0-59)>
Moxa Command Line Interface Commands
3-46
Configure Scheduling Rule Setting
Commands
poe scheduling <rule-name: string(63)> activate
no poe scheduling <rule-name: string(63)> activate
Syntax Description
no
Remove configuration/delete entry/reset to default value
poe
Configure PoE parameters
scheduling
Schedule PoE with rules
rule-name: string (63)
The scheduling rule name as the index key
activate
Activate the PoE scheduling rule
Defaults
The scheduling rule is not activated by default
Command Modes
Privileged EXEC
Global Configuration
Usage Guidelines
Activate a rule to apply the rule.
Examples
moxa(config)# poe scheduling <rule-name: string (63)> activate
moxa(config)# no poe scheduling <rule-name: string (63)> activate
Error Messages
N/A
Related Commands
show poe scheduling [<rule-name: string(63)>]
poe scheduling <rule-name: string(63)> <start-date-year: integer(1970-2038)>
<start-date-month: integer(1-12)> <start-date-day: integer(1-31)> <start-time-hour:
integer(0-24)> <start-time-min: integer(0-59)> <end-time-hour: integer(0-24)>
<end-time-min: integer(0-59)>
Moxa Command Line Interface Commands
3-47
Configure Scheduling Repeat Setting
Commands
poe scheduling <rule-name: string(63)> repeat { daily | weekday | weekend | sunday | monday | tuesday
| wednesday | thursday | friday | saturday }
no poe scheduling <rule-name: string(63)> repeat { daily | weekday | weekend | sunday | monday |
tuesday | wednesday | thursday | friday | saturday }
Syntax Description
no
Remove configuration/delete entry/reset to default value
poe
Configure PoE parameters
scheduling
Schedule PoE with rules
rule-name: string (63)
The scheduling rule name as the index key
repeat
Repeat PoE scheduling rules
daily
Repeat daily
weekday
Repeat on weekdays
weekend
Repeat on weekends
sunday
Repeat every Sunday
monday
Repeat every Monday
tuesday
Repeat every Tuesday
wednesday
Repeat every Wednesday
thursday
Repeat every Thursday
friday
Repeat every Friday
saturday
Repeat every Saturday
Defaults
N/A
Command Modes
Privileged EXEC
Global Configuration
Usage Guidelines
Set PoE scheduling rules to repeat on the specified day(s).
Examples
moxa(config)# no poe scheduling <rule-name: string(63)> repeat {daily | weekday |
weekend | sunday | monday | tuesday | wednesday | thursday | friday | saturday}
Error Messages
N/A
Related Commands
show poe scheduling [<rule-name: string(63)>]
poe scheduling <rule-name: string(63)> <start-date-year: integer(1970-2038)>
<start-date-month: integer(1-12)> <start-date-day: integer(1-31)> <start-time-hour:
integer(0-24)> <start-time-min: integer(0-59)> <end-time-hour: integer(0-24)>
<end-time-min: integer(0-59)>
Configure Port Power Output Setting
Commands
poe
no poe
Syntax Description
no
Remove configuration/delete entry/reset to default value
poe
Configure PoE parameters
Defaults
Port PoE power output is enabled by default
Command Modes
Privileged EXEC
Interface Configuration
Usage Guidelines
N/A
Examples
moxa(config-if)# poe
moxa(config-if)# no poe
Error Messages
N/A
Related Commands
show poe [interface <iftype> <ifnum>] {config | status | diagnosis}
Moxa Command Line Interface Commands
3-48
Configure Port Power Output Mode Setting
Commands
poe output-mode { auto | high-power | force power-allocation <watt: integer(0-36)> }
Syntax Description
poe
Configure PoE parameters
output-mode
The power output mode depending on the connected PD
auto
Standard output mode
high-power
Standard output mode with a higher power limit
force
Non-standard or legacy output mode
power-allocation
Power output limit for high-power mode and force mode
watt: integer (0-36)
The port PoE power output limit
Defaults
The output mode is set to auto by default
Command Modes
Privileged EXEC
Interface Configuration
Usage Guidelines
Auto mode is suitable for standard 802.3af/at PDs. The power allocation value should be
set to 0.
High-power mode is suitable for standard 802.3af/at PDs that require more than 30
watts of power. The power allocation value should be set to 36.
Force mode is suitable for non-standard PDs.
Examples
moxa(config-if)# poe output-mode {auto | high-power | force power-allocation <watt:
integer(0-36)>}
Error Messages
'Invalid: In PoE Output Auto Mode, the Power Allocation value is not valid.'
'Invalid: Sum of power allocation cannot exceed system power budget.'
'Invalid: In PoE Output High-Power Mode, the Power Allocation value is not valid.'
Related Commands
show poe [interface <iftype> <ifnum>] {config | status | diagnosis}
Reset PoE Output Mode
Commands
no poe output-mode
Syntax Description
no
Remove configuration/delete entry/reset to default value
poe
Configure PoE parameters
output-mode
The power output mode depending on the connected PD
Defaults
The output-mode is set to auto by default
Command Modes
Privileged EXEC
Global Configuration
Usage Guidelines
N/A
Examples
moxa(config-if)# no poe output-mode
Error Messages
'Invalid: In PoE Output Auto Mode, the Power Allocation value is not valid.'
Related Commands
show poe [interface <iftype> <ifnum>] {config | status | diagnosis}
Moxa Command Line Interface Commands
3-49
Configure Port Legacy PD Detection Settings
Commands
poe legacy-pd-detection
no poe legacy-pd-detection
Syntax Description
no
Remove configuration/delete entry/reset to default value
poe
Configure PoE parameters
legacy-pd-detection
Use legacy PD detection to power PDs if the capacitance of
the PD is higher than 2.7 μF or less than 10 μF
Defaults
Legacy PD detection is disabled by default.
Command Modes
Privileged EXEC
Interface Configuration
Usage Guidelines
Enable legacy PD detection on ports to power PDs within the 2.7 to 10 μF capacitance
range
Examples
moxa(config-if)# poe legacy-pd-detection
moxa(config-if)# no poe legacy-pd-detection
Error Messages
N/A
Related Commands
show poe [interface <iftype> <ifnum>] {config | status | diagnosis}
Configure Port Auto Power Cutting Priority Setting
Commands
poe priority { critical | high | low }
no poe priority
Syntax Description
no
Remove configuration/delete entry/reset to default value
poe
Configure PoE parameters
priority
The priority for automatically PoE cutting power
critical
Critical priority
high
High priority
low
Low priority
Defaults
The priority is set to low by default
Command Modes
Privileged EXEC
Interface Configuration
Usage Guidelines
Set the port priority for automatically cutting PoE power. Lower priority devices will be
cut off first.
Examples
moxa(config-if)# poe priority { critical | high | low }
moxa(config-if)# no poe priority
Error Messages
N/A
Related Commands
show poe [interface <iftype> <ifnum>] {config | status | diagnosis}
poe auto-power-cutting
no poe auto-power-cutting
Moxa Command Line Interface Commands
3-50
PoE Status
Show System and Port Setting, Status, and Diagnosis
Commands
show poe [ interface <iftype> <ifnum> ] { config | status | diagnosis }
Syntax Description
show
Display configuration/status information
poe
Display PoE information
interface
Interface information
iftype
The interface type
ifnum
The interface number
config
The current PoE configuration applied to the port
status
The PoE status
diagnosis
PoE diagnosis
Defaults
N/A
Command Modes
User EXEC
Privileged EXEC
Usage Guidelines
N/A
Examples
moxa# show poe [interface <iftype> <ifnum>] {config | status | diagnosis}
Error Messages
N/A
Related Commands
poe {enable | disable}
poe system-power-budget <watt: integer(30-720)>
poe auto-power-cutting
no poe auto-power-cutting
poe
no poe
poe output-mode { auto | high-power | force power-allocation <watt: integer(0-36)> }
poe legacy-pd-detection
no poe legacy-pd-detection
poe priority { critical | high | low }
no poe priority
Show Port PD Failure Check Setting and Status
Commands
show poe pd-failure-check [ interface <iftype> <ifnum> ] { config | status }
Syntax Description
show
Display configuration/status information
poe
Display PoE information
pd-failure-check
Check the PD failure status
interface
Interface information
iftype
The interface type
ifnum
The interface number
config
The current PoE configuration applied to the port
status
PoE status
Defaults
N/A
Command Modes
User EXEC
Privileged EXEC
Usage Guidelines
N/A
Examples
moxa# show poe pd-failure-check [interface <iftype> <ifnum>] {config | status}
Error Messages
N/A
Related Commands
poe pd-failure-check [ { device-ip <ucast_addr> | check-frequency <seconds:
integer(5-300)> | no-response-times <times: integer(1-10)> | action { no-action |
restart-pd | shutdown-pd } } ]
no poe pd-failure-check
Moxa Command Line Interface Commands
3-51
Show Scheduling Rule Setting
Commands
show poe scheduling [ <rule-name: string(63)> ]
Syntax Description
show
Display configuration/status information
poe
Display PoE information
scheduling
Schedule PoE availability with rules
rule-name:string (63)
The scheduling rule name
Defaults
N/A
Command Modes
User EXEC
Privileged EXEC
Usage Guidelines
N/A
Examples
moxa# show poe scheduling [<rule-name: string(63)>]
Error Messages
N/A
Related Commands
poe scheduling <rule-name: string(63)> <start-date-year: integer(1970-2038)>
<start-date-month: integer(1-12)> <start-date-day: integer(1-31)> <start-time-hour:
integer(0-24)> <start-time-min: integer(0-59)> <end-time-hour: integer(0-24)>
<end-time-min: integer(0-59)>
poe scheduling <rule-name: string(63)> activate
no poe scheduling <rule-name: string(63)> activate
poe scheduling <rule-name: string(63)> repeat { daily | weekday | weekend | sunday |
monday | tuesday | wednesday | thursday | friday | saturday }
no poe scheduling <rule-name: string(63)> repeat { daily | weekday | weekend |
sunday | monday | tuesday | wednesday | thursday | friday | saturday }
poe scheduling <rule-name: string(63)>
no poe scheduling <rule-name: string(63)>
Moxa Command Line Interface Commands
3-52
Layer 2 Switching
VLAN
IEEE 802.1Q
Show VLAN Device Information
Commands
show vlan device info
Syntax Description
vlan
Display VLAN bridge status and information
device
The VLAN device
info
Information
Defaults
N/A
Command Modes
Privileged EXEC/ User EXEC
Usage Guidelines
N/A
Examples
moxa# show vlan device info
vlan device configurations
--------------------------
vlan Status : Enabled
vlan Oper status : Enabled
gvrp status : Enabled
gmrp status : Enabled
gvrp Oper status : Enabled
gmrp Oper status : Enabled
Bridge Mode : Customer Bridge
Base-Bridge Mode : Vlan Aware Bridge
blan Operational Learning Mode : IVL
Hybrid Default Learning Mode : IVL
Version number : 1
Max Vlan id : 4094
Max supported vlans : 256
Error Messages
N/A
Related Commands
gvrp
gmrp
bridge-mode
Moxa Command Line Interface Commands
3-53
Show VLAN Interface Status
Commands
show vlan [{brief | id <vlan-range> | summary | ascending}]
Syntax Description
show
Display configuration/statistics/general information
Vlan
Display the VLAN interface status
brief
Display the VLAN entry related information of all active VLANs and
VLANs (that are not active) for which the port details are
configured.
id
The VLAN index
vlan-range
The VLAN index range (ex: 1-10 means the VID 1 to VID 10)
summary
Display the total number of VLANs
ascending
Display information for all VLANs in ascending order
Defaults
N/A
Command Modes
Privileged EXEC/ User EXEC
Usage Guidelines
N/A
Examples
moxa# show vlan brief
vlan database
-------------
vlan ID : 1
Member Ports : Eth1/1, Eth1/2, Eth1/3, Eth1/4, Eth2/1, Eth2/2
Eth2/3, Eth2/4, Eth3/1, Eth3/2, Eth3/3, Eth3/4
Eth4/1, Eth4/2, Eth4/3, Eth4/4, Eth5/1, Eth5/2
Eth5/3, Eth5/4, Eth6/1, Eth6/2, Eth6/3, Eth6/4
Eth7/1, Eth7/2, Eth7/3, Eth7/4
Untagged Ports : Eth1/1, Eth1/2, Eth1/3, Eth1/4, Eth2/1, Eth2/2
Eth2/3, Eth2/4, Eth3/1, Eth3/2, Eth3/3, Eth3/4
Eth4/1, Eth4/2, Eth4/3, Eth4/4, Eth5/1, Eth5/2
Eth5/3, Eth5/4, Eth6/1, Eth6/2, Eth6/3, Eth6/4
Eth7/1, Eth7/2, Eth7/3, Eth7/4
Forbidden Ports : None
Name :
Status : Permanent
Egress Ethertype : 0x8100
----------------------------------------------------
Error Messages
N/A
Related Commands
vlan <vlan-id>
ports add <interface-type> <1/a-b> untagged <interface-type> <1/a-b> forbidden
<interface-type> <1/a-b>
vlan active
vlan name
Moxa Command Line Interface Commands
3-54
Show VLAN Port Configuration
Commands
show vlan port config port [port {port-channel <integer> | < interface-type > < interface-id> }]
Syntax Description
show
Display configuration/statistics/general information
vlan
Display VLAN interface status
port
The port interface
config
The port’s configuration
port
The port interface
port-channel <integer>
The port channel ID
This number is the max number of trunk group IDs
interface-type
The Ethernet type
interface-id integer
The interface ID: slot number/port number
Defaults
N/A
Command Modes
Privileged EXEC/ User EXEC
Usage Guidelines
N/A
Examples
moxa# show
vlan port config port ethernet 1/3
Vlan Port configuration table
-------------------------------
Port Eth1/3
Bridge Port Type : Customer Bridge Port
Port Vlan ID : 1
Port Acceptable Frame Type : Admit All
Port Ingress Filtering : Disabled
Port Mode : Hybrid
Port Gvrp Status : Enabled
Port Gmrp Status : Enabled
Port Gvrp Failed Registrations : 0
Gvrp last pdu origin : 00:00:00:00:00:00
Port Restricted Vlan Registration : Disabled
Port Restricted Group Registration : Disabled
Default Priority : 0
Filtering Criteria : Default
Ingress EtherType : 0x8100
Egress EtherType : 0x8100
Error Messages
N/A
Related Commands
Switchport pvid
Switchport acceptable-frame-type
Switchport ingress-filter
Switchport mode
gvrp
gmrp
vlan restricted
group restricted
switchport filtering-utility-criteria
Moxa Command Line Interface Commands
3-55
Show MAC Address Table Information
Commands
show mac-address-table [vlan <vlan-range>] [address <aa:aa:aa:aa:aa:aa>] [interface <interface-type>
<interface-id> ]
show mac-address-table aging-time
show mac-address-table count [vlan <vlan-id>]
show mac-address-table dynamic multicast [vlan <vlan-range>] [address <aa:aa:aa:aa:aa:aa>]
[interface {port-channel <integer> | <interface-type> <interface-id> }]
show mac-address-table dynamic unicast [vlan <vlan-range>] [address <aa:aa:aa:aa:aa:aa>]
[interface {port-channel <integer> | <interface-type> <interface-id> }]
show mac-address-table static multicast [vlan <vlan-range>] [address <aa:aa:aa:aa:aa:aa>] [interface
{port-channel <integer> | <interface-type> <interface-id> }]
show mac-address-table static unicast [vlan <vlan-range>] [address <aa:aa:aa:aa:aa:aa>] [interface
{port-channel <integer> | <interface-type> <interface-id> }]
Syntax Description
show
Display configuration/statistics/general information
mac-address-table
Display MAC address information
address
MAC address entry
aging-time
Maximum age of a Mac address table entry
count
Number of MAC addresses present on all the VLANs or on a
specified VLAN
dynamic
Dynamic learned MAC address
static
Static configured MAC address
multicast
Multicast MAC address
unicast
Unicast MAC address
vlan
The VLAN interface
vlan-range
The VLAN ID range for which the details will be displayed.
This value ranges from 1 to 4094. For example, 4000-4010
will show information for those VLAN IDs.
interface-type
port-channel
The Ethernet type
interface-id
integer
The interface ID: slot number/port number
Defaults
N/A
Command Modes
Privileged EXEC/ User EXEC
Usage Guidelines
N/A
Examples
moxa# show mac-address-table
vlan Mac Address Type ConnectionId Ports
---- ----------- ---- ----------- -----
1 00:00:5e:00:01:02 Learnt Eth1/3
1 00:21:cc:62:f7:0b Learnt Eth1/3
1 00:21:cc:72:a8:d7 Learnt Eth1/3
Total Mac Addresses displayed: 3
Error Messages
N/A
Related Commands
mac-address-table
Moxa Command Line Interface Commands
3-56
Show MAC Address Table for Dynamic Multicast and Unicast
Commands
show mac-address-table dynamic multicast [vlan <vlan-range>] [address <aa:aa:aa:aa:aa:aa>]
[interface {port-channel <integer> | <interface-type> <interface-id> }]
show mac-address-table dynamic unicast [vlan <vlan-range>] [address <aa:aa:aa:aa:aa:aa>]
[interface {port-channel <integer> | <interface-type> <interface-id> }]
Syntax Description
show
Display configuration/statistics/general information
mac-address-table
Display MAC address information
dynamic
Display dynamically learned MAC addresses
multicast
The multicast MAC addresseses
unicast
The unicast MAC addresses
vlan
The VLAN interface
vlan-range
The VLAN ID range for which the details will be displayed.
This value ranges from 1 to 4094. For example, 4000-4010
will show information for those VLAN IDs.
interface-type
port-channel
The Ethernet type
The port-channel
interface-id
The slot number/port number
Defaults
N/A
Command Modes
Privileged EXEC/User EXEC
Usage Guidelines
N/A
Examples
moxa# show mac-address-table dynamic unicast
vlan Mac Address Type ConnectionId Ports
---- ----------- ---- ------------- -----
1 00:00:5e:00:01:02 Learnt Eth1/3
1 00:05:1b:a1:ae:62 Learnt Eth1/3
1 00:0c:29:9b:83:e9 Learnt Eth1/3
….
Total Mac Addresses displayed: 44
iss# show mac-address-table dynamic multicast
vlan Mac Address Type ConnectionId Ports
---- ----------- ---- ----------- -----
Total Mac Addresses displayed: 0
Error Messages
N/A
Related Commands
mac-address-table
Moxa Command Line Interface Commands
3-57
Show MAC Address Table for Static Multicast and Unicast
Commands
show mac-address-table static multicast [vlan <vlan-range>] [address <aa:aa:aa:aa:aa:aa>] [interface
{port-channel <integer> | <interface-type> <interface-id> }]
show mac-address-table static unicast [vlan <vlan-range>] [address <aa:aa:aa:aa:aa:aa>] [interface
{port-channel <integer> | <interface-type> <interface-id> }]
Syntax Description
show
Display configuration/statistics/general information
mac-address-table
Display MAC address information
static
Static entry
multicast
The multicast MAC address
unicast
The unicast MAC address
vlan
The VLAN interface
vlan-range
The VLAN ID range for which the details will be displayed.
This value ranges from 1 to 4094. For example, 4000-4010
will show information for those VLAN IDs.
interface-type
port-channel
The Ethernet type
The port-channel
interface-id
The slot number/port number
Defaults
N/A
Command Modes
Privileged EXEC/ User EXEC
Usage Guidelines
N/A
Examples
moxa# show mac-address-table static multicast vlan 1
Static Multicast Table
----------------------
Vlan : 1
Mac Address : 01:00:00:00:11:22
Receive Port : Eth1/3
Member Ports : Eth1/1
Forbidden Ports :
Status : Permanent
------------------------------------------------
Vlan : 1
Mac Address : 01:00:00:11:22:33
Receive Port :
Member Ports : Eth1/1, Eth1/2, Eth1/3, Eth1/4, Eth1/5, Eth1/6
Eth1/7, Eth1/8, Eth1/9, Eth1/10, Eth1/11, Eth1/12
Forbidden Ports :
Status : Permanent
------------------------------------------------
Total Mac Addresses displayed: 2
iss# show mac-address-table static unicast
vlan Mac Address RecvPort Status ConnectionId Ports
---- ----------- -------- ------ ------------ -----
1 00:12:23:34:45:56 Permanent Eth1/3
1 00:31:13:31:13:13 DeleteOnReset Eth1/3
1 00:44:33:44:33:44 Permanent Eth1/4
Total Mac Addresses displayed: 3
Moxa Command Line Interface Commands
3-58
Error Messages
N/A
Related Commands
mac-address-table
Show GVRP Statistics
Commands
show gvrp statistics [{port {port-channel <integer> | <interface-type> <interface-id>}]
Syntax Description
show
Display configuration/statistics/general information
gvrp statistics
Display GVRP statistics
interface-type
port-channel
The Ethernet type
The port-channel
interface-id
The slot number/port number
Defaults
N/A
Command Modes
Privileged EXEC/ User EXEC
Usage Guidelines
N/A
Examples
moxa# show gvrp statistics port ethernet 1/3
GVRP Statistics for Port Eth1/3
---------------------------------------
Total valid GVRP Packets Received: 18
Join Emptys 0
Join In 1
Leave In 0
Leave All 17
Leave Empty 0
Empty 0
Total valid GVRP Packets Transmitted: 324
Join Emptys 0
Join In 324
Leave In 0
Leave All 0
Leave Empty 0
Empty 0
moxa# show gmrp statistics port ethernet 1/3
GMRP Statistics for Port Eth1/3
---------------------------------------
Total valid GMRP Packets Received 0:
Join Emptys 0
Join In 0
Leave In 0
Leave All 0
Leave Empty 0
Empty 0
Total valid GMRP Packets Transmitted:358
Join Emptys 0
Join In 358
Leave In 0
Leave All 0
Leave Empty 0
Empty 0
Moxa Command Line Interface Commands
3-59
Error Messages
N/A
Related Commands
vlan active
Show VLAN Management
Commands
show management vlan
Syntax Description
show
Display configuration/statistics/general information
management
Display Management VLAN information
vlan
The VLAN interface
Defaults
N/A
Command Modes
Privileged EXEC/ User EXEC
Usage Guidelines
N/A
Examples
moxa# show management vlan
Management VLAN-List
1,2, …..
Error Messages
N/A
Related Commands
Management vlan
No management vlan
Create/Delete a VLAN
Commands
vlan <vlan-id>
no vlan <vlan-id>
vlan active
vlan name < vlan name string >
SyntaxDescription
vlan/no vlan
Create/delete a VLAN
vlan-id
The VLAN identifier
active
Activate the VLAN
name < vlan name string >
The VLAN name string consisting of a total of 32
characters
Defaults
N/A
Command Modes
Configuration
Usage Guidelines
N/A
Examples
moxa(config)# vlan 100
moxa(config-vlan)# vlan active
moxa(config)# no vlan 100
moxa(config)#
Error Messages
N/A
Related Commands
interface vlan <vlan-id>
show vlan
Configure VLAN Mode
Commands
ports add {member ([<iftype> <iface_list>][port-channel <integer>]) | untagged ([<iftype>
<iface_list>][port-channel <integer>]) | forbidden ([<iftype> <iface_list>][port-channel <integer>])}
vlan ports set member ([<iftype> <iface_list>][port-channel <integer>]) [untagged ([<iftype>
<iface_list>][port-channel <integer>])] [forbidden ([<iftype> <iface_list>][port-channel <integer>])]
Moxa Command Line Interface Commands
3-60
vlan ports add {member | untagged | forbidden} [<interface-type> <slot/port-port,slot/port,...>]
[port-channel <integer>]
no ports [<interface-type> <slot/port-port,slot/port,...>] [port-channel <integer>] [untagged
([<interface-type> <slot/port-port,slot/port,...>] [port-channel <integer>])] [forbidden ([<interface-type>
<slot/port-port,slot/port,...>] [port-channel <integer>])]
Syntax Description
Ports/no ports
Set/delete member/untagged/forbidden port
add
Add member/untag/forbidden port
set
Overwrite member/untagged/forbidden port
slot/port-port
The slot number/port number
interface-type
The Ethernet type
port-channel
<1-N> Set the list of port channel interfaces or a specific port
channel identifier.
member
Configure the ports to be set as a member of the VLAN
untagged
Configure the ports that will be used by the VLAN to transmit
egress traffic as untagged packets.
forbidden
Configures the ports to never receive packets from the VLAN
Defaults
N/A
Command Modes
Config VLAN mode
Usage Guidelines
This command can only be executed from within VLAN configuration mode. From
Configuration mode, enter vlan <vlan-id> to enter VLAN config mode.
Examples
moxa(config)# vlan 10
moxa(config-vlan)#ports add member ethernet 1/3 untagged all
moxa(config-vlan)#ports add member ethernet 1/3 untagged ethernet 1/3 forbidden
ethernet 1/2
Error Messages
N/A
Related Commands
vlan active
switchport mode
show vlan
show mac-address-table count
Moxa Command Line Interface Commands
3-61
Configure a Static Unicast MAC Address in the Forwarding Database
Commands
mac-address-table static unicast <aa:aa:aa:aa:aa:aa> vlan <vlan-id> set [interface ([<interface-type>
<slot/port-port,slot/port,...>] [<interface-type> <slot/port-port,slot/port,...>] [port-channel <a,b,c-d>] )]
[status { permanent }]
no mac-address-table static unicast <aa:aa:aa:aa:aa:aa> vlan <vlan-id>
Syntax Description
mac-address-table
Configure mac-address-table parameters
static
The statically configured MAC address
unicast
Configure the unicast MAC address
aa:aa:aa:aa:aa:aa
The unicast MAC address
vlan
Configure the VLAN
vlan-id
The VLAN id
set
Set the unicast MAC address to a specified port
interface-type
The Ethernet type
The port-channel
interface-id
The slot number/port number
status
Set the status of the static unicast entry
permanent
The entry remains even after the next reset of the bridge
Defaults
N/A
Command Modes
Configuration
Usage Guidelines
N/A
Examples
moxa(config)#mac-address-table static unicast 00:11:22:33:22:11 vlan 1 set ethernet
1/2 status permanent
Error Messages
N/A
Related Commands
mac-address-table static multicast
vlan
vlan ports add
show mac-address-table static unicast
Globally Enable/Disable GVRP on All Ports
Commands
gvrp {enable | disable}
Syntax Description
gvrp
Configure GVRP parameters
enable
Enable on all ports and start the GVRP on the switch
disable
Disable GVRP on all ports.
Defaults
GVRP is disabled by default
Command Modes
Configuration
Usage Guidelines
N/A
Examples
moxa(config)# gvrp enable
Error Messages
N/A
Related Commands
bridge-mode
show vlan device info
show gvrp statistics
Enable/Disable GVRP on Specific Ports
Commands
gvrp
no gvrp
Moxa Command Line Interface Commands
3-62
Syntax Description
no
Remove configuration/delete entry/reset to default value
gvrp
Configure GVRP parameters
GVRP: Enable GVRP on the specific port(s)
No GVRP: Disable GVRP on the specific port(s)
Defaults
GVRP is disabled by default
Command Modes
Configuration
Usage Guidelines
N/A
Examples
moxa# interface Ethernet 1/1
moxa(config-if)# gvrp
Error Messages
N/A
Related Commands
show vlan port config
show gvrp statistics
Configure MAC Address Table Aging Time
Commands
mac-address-table aging-time <10-300 seconds>
no mac-address-table aging-time
Syntax Description
no
Remove configuration/delete entry/reset to default value
mac-address-table
Configure the MAC-address-table
aging-time
Maximum age of an entry in the MAC address table to its
default value.
second
The aging time ranging from 10 to 300 seconds
Defaults
300s
Command Modes
Configuration
Usage Guidelines
N/A
Examples
moxa(config)# mac-address-table aging-time 100
Error Messages
N/A
Related Commands
show mac-address-table aging-time
Moxa Command Line Interface Commands
3-63
Configure PVID on a Specified Port
Commands
switchport pvid <vlan-id>
no switchport pvid
Syntax Description
no
Remove configuration/delete entry/reset to default value
pvid
Configure port-based VLAN parameters
vlan-id
The VLAN ID, ranging from 1 to 4094.
Defaults
1
Command Modes
Configuration
Usage Guidelines
If a PVID does not exist for this system, it will be created automatically after
configuration.
If the port is configured to be in Access Mode, the actions below will be applied
automatically.
1. Remove this port from member port list if it is bound to another VID which is
different from PVID
2. Modify this port into an untagged member of this PVID
If the port is configured to be in Trunk Mode, the port will automatically be modified into
a tagged member of this PVID.
Examples
moxa(config-if)# switchport pvid 1
Error Messages
N/A
Related Commands
switchport
vlan vlan active
switchport acceptable-frame-type
Configure VLAN-dependent BPDU Frames
Commands
switchport acceptable-frame-type {all | tagged | untaggedAndPrioritytagged }
Syntax Description
acceptable-frame-type
Configure acceptable-frame-type parameters
all
Configures the acceptable frame type as all which
are acceptable and subjected to ingress filtering.
tagged
Configures the acceptable frame type as tagged.
untaggedAndPrioritytagged
Configures the acceptable frame type as untagged
and priority tagged.
Defaults
all
Command Modes
Configuration
Usage Guidelines
N/A
Examples
moxa(config-if)# switchport acceptable-frame-type untaggedAndPrioritytagged
Error Messages
N/A
Related Commands
switchport
switchport pvid
switchport ingress-filter
switchport mode
show vlan port config
Moxa Command Line Interface Commands
3-64
Enable/Disable Ingress Filter
Commands
switchport ingress-filter
no switchport ingress-filtering
Syntax Description
no
Remove configuration/delete entry/reset to default value
switchport
The switch port
ingress-filtering
Enable ingress-filtering
Defaults
disable
Command Modes
Configuration
Usage Guidelines
N/A
Examples
moxa (config-if)# switchport ingress-filter
moxa (config-if)# no switchport ingress-filter
Error Messages
N/A
Related Commands
switchport
switchport acceptable-frame-type
show vlan port config
Configure Switch Port Operation Mode
Commands
switchport mode {access | trunk | hybrid}
Syntax Description
switchport
Configure the switch port
mode
Configure switch port mode parameters
access
Configure the port as an access port that accepts and sends only
untagged packets. This kind of port is added as a member to a
specific VLAN and only carries traffic for the VLAN to which the port
is assigned. The port can only be set as an access port if the
following 4 conditions are met:
1. GVRP is disabled for that port.
2. The acceptable frame type is set as “Admit untagged and
pri-tagged”.
3. The port is not a tagged member of any VLAN.
4. The PVID is the same as the only untagged VLAN it joined.
trunk
Configures the port as trunk port that accepts and sends only
tagged frames. This kind of port is added as members of several
existing VLANs, and carries traffic for all of them. The port can only
be set as a trunk port. if the following 2 conditions are met:
1. The acceptable frame type is set as “Admit tagged only”
2. The port is not an untagged member of any VLAN.
hybrid
Configures the port as a hybrid port that accepts and sends both
tagged and untagged frames
Defaults
The default port operation mode is set to Hybrid
Command Modes
Configuration
Usage Guidelines
When changing from trunk or hybrid to access mode, the following changes will be
automatically applied:
Forces the port to become an untagged member of the PVID domain
If the port exists in another VLAN, it will be removed
Forces the accept frame type to be set to “Admit untagged and pri-tagged”
When changing from access or hybrid to trunk mode, the following changes will be
automatically applied:
Moxa Command Line Interface Commands
3-65
Forces the port to become a tagged member of the PVID domain
If the port was an untagged member in another VLAN, it will changed into a tagged
member.
Forces the accept frame type to be set to “Admit tagged only”
When changing from access or trunk to hybrid mode, there will be no changes
Examples
moxa (config-if)# switchport mode hybrid
Error Messages
N/A
Related Commands
switchport
port gvrp
vlan ports
switchport acceptable-frame-type
show vlan port config
Configure Restricted VLAN Registration
Commands
vlan restricted
Syntax Description
vlan restricted
Configure restricted VLAN parameters
Enable or disable the restricted VLAN registration feature on the
port. Enabled means the creation or modification of a dynamic
VLAN entry is permitted only for VLANs for which static VLAN
registration entries exist. Disabled means the creation or
modification of a dynamic VLAN entry is permitted for all VLANs.
Defaults
Restricted VLAN registration is disabled by default
Command Modes
Privileged EXEC/ User EXEC
Usage Guidelines
N/A
Examples
moxa(config-if)# vlan restricted
Error Messages
N/A
Related Commands
show vlan port config
Create Filtering Utility Criteria
Commands
switchport filtering-utility-criteria {default | enhanced}
Syntax Description
filtering-utility-criteria
Configure VLAN filtering utility criteria
default
Only allow the learning of a source MAC from a packet
received on the port if there is at least one member port for
a VLAN mentioned in the packet.
enhanced
Only allow the learning of source MAC from a packet
received on the port if the following conditions are met:
At least one VLAN that uses the FID indicates the reception
port and at least one other port with a port state of learning
or forwarding in its member set
Ingress to the VLAN is permitted through a port other than
the source and reception ports. This port can be or not be a
member of the VLAN.
Defaults
By default, the VLAN filtering utility criteria is set to default
Command Modes
Privileged EXEC/ User EXEC
Usage Guidelines
N/A
Examples
moxa(config-if)# switchport filtering-utility-criteria default
Error Messages
N/A
Related Commands
show vlan port config
Moxa Command Line Interface Commands
3-66
Set VLAN Access Port
Commands
switchport access vlan <vlan-id>
Syntax Description
switchport access
Configure the port as an access port
vlan <vlan-id>
The specified VLAN ID for which this access port will carry
traffic, ranging from 1 to 4094.
Defaults
The port mode is set to access port by default
Command Modes
Privileged EXEC/ User EXEC
Usage Guidelines
Disgarding the current operation mode of the port, this command will change the port to
access mode and the following changes will automatically apply:
Forces the acceptable frame type to be set to “untagged AND priority tagged”
Sets PVID to specified a VLAN
Changes the port into an untagged member of a specified VLAN and removes this port
from any other VLANs.
Sets the port mode to access mode
Examples
moxa(config-if)# switchport access vlan 10
Error Messages
N/A
Related Commands
show vlan port config
show vlan
Configure VLAN Management
Commands
management vlan <vlan-id>
no management vlan <vlan>
Syntax Description
no
Remove configuration/delete entry/reset to default value
management
Configure management
vlan
Configure the management VLAN
vlan-id
The management VLAN ID
Defaults
The default management VLAN ID is set to 1
Command Modes
Privileged EXEC/ User EXEC
Usage Guidelines
N/A
Examples
moxa(config)# management vlan 1
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-67
Show VLAN Statistic
Commands
show vlan statistics [vlan <vlan-range>]
Syntax Description
show
Display configuration/statistics/general information
vlan
Configure VLAN parameters
statistics
Display VLAN-related statistics
vlan
Display the VLAN
vlan-range
Display the VLAN range
Defaults
N/A
Command Modes
Privileged EXEC/ User EXEC
Usage Guidelines
N/A
Examples
moxa# show vlan statistics vlan 3
Software Statistics Disabled
Unicast/broadcast Vlan statistics
Error Messages
N/A
Related Commands
N/A
GARP
Show GARP Timer
Commands
show garp timer [port {port-channel <integer> | <interface-type> <interface-id>}]
Syntax Description
show
Display configuration/statistics/general information
garp timer
Display GARP timer information
interface-type
port-channel
The Ethernet type
The port-channel
interface-id
The slot number/port number
Defaults
N/A
Command Modes
Privileged EXEC/ User EXEC
Usage Guidelines
N/A
Examples
moxa# show garp timer
Garp Port Timer Info (in milli seconds)
---------------------------------------
Port Join-time Leave-time Leave-all-time
----- --------- ---------- --------------
Eth1/1 200 600 10000
Eth1/2 200 600 10000
Eth1/3 200 600 10000
Eth1/4 200 600 10000
Eth2/1 200 600 10000
Eth2/2 200 600 10000
Eth2/3 200 600 10000
Eth2/4 200 600 10000
…..
Error Messages
N/A
Related Commands
garp timer
no shutdown garp
Moxa Command Line Interface Commands
3-68
MAC
Static Unicast
Configure a Static Unicast MAC Address in the Forwarding Database
Commands
config mac-address-table static unicast <aa:aa:aa:aa:aa:aa> vlan <vlan-id> set [interface
([<interface-type> <slot/port-port,slot/port,...>] [<interface-type> <slot/port-port,slot/port,...>]
[port-channel <a,b,c-d>] )] [status { permanent }]
config no mac-address-table static unicast <aa:aa:aa:aa:aa:aa> vlan <vlan-id>
Syntax Description
no
Remove configuration/delete entry/reset to default value
mac-address-table
Configure MAC address table parameters
static
Statically configured MAC address
unicast
The unicast MAC address
set
Overwrite port
interface-type
The Ethernet type
The port-channel
interface-id
The slot number/port number
status
Specify the status of the static unicast entry:
permanent - entry remains even after the next reset of the
bridge
Defaults
N/A
Command Modes
Privileged EXEC/ User EXEC
Usage Guidelines
N/A
Examples
moxa(config)# mac-address-table static unicast aa:aa:aa:bb:bb:cc vlan 168 set
interface ethernet 2/4 status permanent
Error Messages
N/A
Related Commands
mac-address-table static multicast
vlan
vlan ports add
show mac-address-table static unicast
Moxa Command Line Interface Commands
3-69
MAC Address Table
Show MAC Address Table Information
Commands
show mac-address-table [vlan <vlan-range>] [address <aa:aa:aa:aa:aa:aa>] [interface <interface-type>
<interface-id> ]
show mac-address-table aging-time
show mac-address-table count [vlan <vlan-id>]
show mac-address-table dynamic multicast [vlan <vlan-range>] [address <aa:aa:aa:aa:aa:aa>]
[interface {port-channel <integer> | <interface-type> <interface-id> }]
show mac-address-table dynamic unicast [vlan <vlan-range>] [address <aa:aa:aa:aa:aa:aa>]
[interface {port-channel <integer> | <interface-type> <interface-id> }]
show mac-address-table static multicast [vlan <vlan-range>] [address <aa:aa:aa:aa:aa:aa>] [interface
{port-channel <integer> | <interface-type> <interface-id> }]
show mac-address-table static unicast [vlan <vlan-range>] [address <aa:aa:aa:aa:aa:aa>] [interface
{port-channel <integer> | <interface-type> <interface-id> }]
Syntax Description
mac-address-table
Display MAC address information
address
The MAC address entry
aging-time
The maximum age of a MAC address table entry
count
The number of MAC addresses present on all VLANs or on a
specified VLAN
dynamic
Dynamically learned MAC address
static
Statically configured MAC address
multicast
The multicast MAC address
unicast
The unicast MAC address
vlan
The VLAN interface
vlan-range
The VLAN ID range for which the details will be displayed.
This value ranges from 1 to 4094. For example, 4000-4010
will show information for those VLAN IDs.
interface-type
port-channel
The Ethernet type
The port-channel
interface-id
The slot number/port number
Defaults
N/A
Command Modes
Privileged EXEC/ User EXEC
Usage Guidelines
N/A
Examples
moxa# show mac-address-table
vlan Mac Address Type ConnectionId Ports
---- ----------- ---- ----------- -----
1 00:00:5e:00:01:02 Learnt Eth1/3
1 00:21:cc:62:f7:0b Learnt Eth1/3
1 00:21:cc:72:a8:d7 Learnt Eth1/3
Total Mac Addresses displayed: 3
Error Messages
N/A
Related Commands
mac-address-table
Moxa Command Line Interface Commands
3-70
QoS
Classification
Configure Mapping Rule for DSCP Priority
Commands
qos ip-dscp-mapping dscp-priority <dscp-priority(0-63)> cos-priority <cos-priority(0-7)>
Syntax Description
qos
Configure QoS parameters
ip-dscp-mapping
Configure mapping rules for DSCP priority
dscp-priority
The DSCP priority
dscp-priority (0-63)
The Differentiated Services Code Point (DSCP) value
cos-priority
The CoS priority
cos-priority (0-7)
The Class of Service (CoS) value
Defaults
N/A
Command Modes
Privileged EXEC
Global Configuration
Usage Guidelines
N/A
Examples
moxa (config)# qos ip-dscp-mapping dscp-priority 0 cos-priority 1
Error Messages
N/A
Related Commands
moxa # show qos ip-dscp-mapping [dscp-priority <integer (0-63)>]
Configure COS Mapping Rule
Commands
qos cos-mapping cos-priority <cos-priority(0-7)> queue-id <queue-id(1-8)>
Syntax Description
qos
Configure QoS parameters
cos-mapping
Configure mapping rules for CoS priority
cos-priority
The CoS priority
cos-priority (0-7)
The VLAN priority
queue-id
The queue index
queue-id (1-8)
The queue index value, ranging from 1 to 8
Defaults
N/A
Command Modes
Global Configuration Mode
Usage Guidelines
N/A
Examples
moxa (config)# qos cos-mapping cos-priority 1 queue-id 2
Error Messages
N/A
Related Commands
moxa# show qos cos-mapping [cos-priority <integer (0-7)>]
Moxa Command Line Interface Commands
3-71
Configure QoS Default Priority Setting
Commands
qos default-priority <default-priority(0-7)>
Syntax Description
qos
Configure QoS parameters
default-priority
Configure the default user priority
default-priority (0-7)
The VLAN priority
Defaults
N/A
Command Modes
Interface Configuration Mode
Usage Guidelines
N/A
Examples
moxa (config-if)# qos default-priority 1
Error Messages
N/A
Related Commands
moxa # show qos defaultPriority [ interface <iftype> <ifnum> ]
Configure QoS P-bit Preference
Commands
qos pbit-preference {dscp | cos}
Syntax Description
qos
Configure QoS parameters
pbit-preference
Configure pbit preference parameters
dscp
Use DSCP priority
cos
Use CoS priority
Defaults
N/A
Command Modes
Interface Configuration Mode
Usage Guidelines
N/A
Examples
moxa (config-if)#qos pbit-preference dscp
Error Messages
N/A
Related Commands
moxa # show qos pbit-preference [interface <iftype> <ifnum>]
Moxa Command Line Interface Commands
3-72
Show QoS DSCP Mapping Rule
Commands
show qos ip-dscp-mapping [dscp-priority <integer (0-63)>]
Syntax Description
show
Display configuration/status information
qos
Display QoS information
ip-dscp-mapping
Display the QoS DSCP mapping table
dscp-priority
The DSCP priority
dscp-priority (0-63)
The Differentiated Services Code Point (DSCP) value
Defaults
N/A
Command Modes
Privileged EXEC Mode
Usage Guidelines
N/A
Examples
moxa # show qos ip-dscp-mapping dscp-priority 1
QoS DSCP Priority Mapping
--------------------------------------------
Dscp Priority 1 mapping to CoS Priority 0
moxa# show qos ip-dscp-mapping
QoS DSCP Priority Mapping
--------------------------------------------
Dscp Priority 0 mapping to CoS Priority 0
Dscp Priority 1 mapping to CoS Priority 0
Dscp Priority 2 mapping to CoS Priority 0
Dscp Priority 3 mapping to CoS Priority 0
Dscp Priority 4 mapping to CoS Priority 0
Dscp Priority 5 mapping to CoS Priority 0
Dscp Priority 6 mapping to CoS Priority 0
……..
Dscp Priority 63 mapping to CoS Priority 7
Error Messages
N/A
Related Commands
moxa (config)# qos ip-dscp-mapping dscp-priority <dscp-priority(0-63)> cos-priority
<cos-priority(0-7)>
Moxa Command Line Interface Commands
3-73
Show QoS COS Mapping Rule
Commands
show qos cos-mapping [cos-priority <integer (0-7)>]
Syntax Description
show
Display configuration/status information
qos
Display QoS information
cos-mapping
Display the QoS CoS mapping table
cos-priority
The CoS priority
cos-priority (0-7)
The VLAN priority value
Defaults
N/A
Command Modes
Privileged EXEC Mode
Usage Guidelines
N/A
Examples
moxa# show qos cos-mapping cos-priority 1
QoS CoS Priority Mapping
--------------------------------------------
CoS Priority 1 mapping to Queue ID 2
moxa # show qos cos-mapping
QoS CoS Priority Mapping
--------------------------------------------
CoS Priority 0 mapping to Queue ID 1
CoS Priority 1 mapping to Queue ID 2
CoS Priority 2 mapping to Queue ID 3
CoS Priority 3 mapping to Queue ID 4
CoS Priority 4 mapping to Queue ID 5
CoS Priority 5 mapping to Queue ID 6
CoS Priority 6 mapping to Queue ID 7
CoS Priority 7 mapping to Queue ID 8
Error Messages
N/A
Related Commands
moxa (config)# qos cos-mapping cos-priority <cos-priority(0-7)> queue-id
<queue-id(1-8)>
Moxa Command Line Interface Commands
3-74
Show QoS Default Priority Setting
Commands
show qos defaultPriority [ interface <iftype> <ifnum> ]
Syntax Description
show
Display configuration/status information
qos
Display QoS information
default-priority
Display the QoS default user priority
interface
Interface information
iftype
The interface type
ifnum
The interface index
Defaults
N/A
Command Modes
Privileged EXEC Mode
Usage Guidelines
N/A
Examples
moxa # show qos default-priority interface ethernet 1/1
QoS Default Priority
--------------------------------------------
Interface Ethernet 1/1 Default Priority is 3
moxa # show qos default-priority
QoS Default Priority
--------------------------------------------
Interface Ethernet 1/1 Default Priority is 3
Interface Ethernet 1/2 Default Priority is 3
Interface Ethernet 1/3 Default Priority is 3
Interface Ethernet 1/4 Default Priority is 3
Interface Ethernet 2/1 Default Priority is 3
Interface Ethernet 2/2 Default Priority is 3
……
Interface Ethernet 7/4 Default Priority is 3
Error Messages
N/A
Related Commands
moxa (config)# qos default-priority <default-priority(0-7)>
Moxa Command Line Interface Commands
3-75
Show QoS P-bit Preference
Commands
show qos pbit-preference [interface <iftype> <ifnum>]
Syntax Description
show
Display configuration/status information
qos
Display QoS information
pbit-preference
Display the pbit preference
interface
Interface information
iftype
The interface type
ifnum
The interface index
Defaults
N/A
Command Modes
Privileged EXEC Mode
Usage Guidelines
If no interface is entered, the QoS pbit preference is shown for all ports.
Examples
moxa # show qos pbit-preference interface ethernet 1/1
QoS P-bit Preference Status
--------------------------------------------
Interface Ethernet 1/1 P-bit Preference is CoS
moxa # show qos pbit-preference
QoS P-bit Preference Status
--------------------------------------------
Interface Ethernet 1/1 P-bit Preference is CoS
Interface Ethernet 1/2 P-bit Preference is CoS
Interface Ethernet 1/3 P-bit Preference is CoS
Interface Ethernet 1/4 P-bit Preference is CoS
Interface Ethernet 2/1 P-bit Preference is CoS
Interface Ethernet 2/2 P-bit Preference is CoS
Interface Ethernet 2/3 P-bit Preference is CoS
Interface Ethernet 2/4 P-bit Preference is CoS
……..
Interface Ethernet 7/4 P-bit Preference is CoS
Error Messages
N/A
Related Commands
moxa (config)# qos pbit-preference {dscp | cos}
Moxa Command Line Interface Commands
3-76
Ingress Rate Limit
Configure Ingress Rate Limit Simple Token Bucket Conform Action: None
Commands
qos rate-limit-type simple-token-bucket cir <cir(1-1000)> [cbs <cbs(10-10240)>] conform-action
do-nothing violate-action drop
Syntax Description
qos
Configure QoS parameters
rate-limit-type
Configure QoS rate limit parameters
simple-token-bucket
Simple Token Bucket
cir
Committed Information Rate
cir(1-1000)
Committed information rate in Mbps
cbs
Committed Burst Size
cbs(10-10240)
Committed burst size in KByte
conform-action
Configure the conform action parameter
do-nothin
Do not perform any action
violate-action
Configure the violate action parameter
drop
Drop the packet
Defaults
N/A
Command Modes
Interface configuration mode
Usage Guidelines
N/A
Examples
moxa (config-if)# qos rate-limit-type simple-token-bucket cir 100 cbs 2000
conform-action do-nothing violate-action drop
Error Messages
'Invalid: {} is greater than the maximum of {}'.format(pre_m_obj['meterCirValue'],
max_rate)
'Invalid: {} is greater than the maximum of {}'.format(pre_m_obj['shaperCirValue'],
max_rate)
'Invalid: {} is greater than the maximum of {}'.format(pre_m_obj['shaperCbsValue'],
max_size)
'Invalid: {} is greater than the maximum of {}'.format(pre_m_obj[key], max_size)
'Invalid: In Simple token bucket mode, when violation action is not drop, conform action
and violate action should be the same.'
Related Commands
moxa # show qos rate-limit [interface <iftype> <ifnum>
Moxa Command Line Interface Commands
3-77
Configure Ingress Rate Limit Simple Token Bucket Conform Action:
Remark-cos
Commands
qos rate-limit-type simple-token-bucket cir <cir(1-1000)> [cbs <cbs(10-10240)>] conform-action
remark-cos <cos-priority(0-7)> violate-action {drop | remark-cos <cos-priority(0-7)>}
Syntax Description
qos
Configure QoS parameters
rate-limit-type
Configure QoS rate limit parameters
simple-token-bucket
Simple Token Bucket
cir
Committed Information Rate
Cir (1-1000)
Committed information rate in Mbps
cbs
Committed Burst Size
Cbs (10-10240)
Committed burst size in KByte
conform-action
Configure the conform action parameter
remark-cos
Remark packet CoS priority
cos-priority (0-7)
The VLAN priority value
violate-action
Configure the violate action parameter
drop
Drop the packet
remark-cos
Remark the packet CoS priority
cos-priority (0-7)
The VLAN priority value
Defaults
N/A
Command Modes
Interface configuration mode
Usage Guidelines
N/A
Examples
moxa (config-if)# qos rate-limit-type simple-token-bucket cir 500 cbs 2000
conform-action remark-cos 6 violate-action drop
Error Messages
'Invalid: {} is greater than the maximum of {}'.format(pre_m_obj['meterCirValue'],
max_rate)
'Invalid: {} is greater than the maximum of {}'.format(pre_m_obj['shaperCirValue'],
max_rate)
'Invalid: {} is greater than the maximum of {}'.format(pre_m_obj['shaperCbsValue'],
max_size)
'Invalid: {} is greater than the maximum of {}'.format(pre_m_obj[key], max_size)
'Invalid: In Simple token bucket mode, when violation action is not drop, conform action
and violate action should be the same.'
Related Commands
moxa # show qos rate-limit [interface <iftype> <ifnum>]
Moxa Command Line Interface Commands
3-78
Configure Ingress Rate Limit Simple Token Bucket Conform Action:
Remark-dscp
Commands
qos rate-limit-type simple-token-bucket cir <cir(1-1000)> [cbs <cbs(10-10240)>] conform-action
remark-dscp <dscp-priority(0-63)> violate-action {drop | remark-dscp <dscp-priority(0-63)>}
Syntax Description
qos
Configure QoS parameters
rate-limit-type
Configure QoS rate limit parameters
simple-token-bucket
Simple Token Bucket
cir
Committed Information Rate
Cir (1-1000)
Committed information rate in Mbps
cbs
Committed Burst Size
cbs (10-10240)
Committed burst size in KByte
conform-action
Configure the conform action parameter
remark-dscp
Remark the packet DSCP priority
dscp-priority (0-63)
The Differentiated Services Code Point (DSCP) value
violate-action
Configure the violate action parameter
drop
Drop the packet
remark-dscp
Remark the packet DSCP priority
dscp-priority (0-63)
The Differentiated Services Code Point (DSCP) value
Defaults
N/A
Command Modes
Interface configuration mode
Usage Guidelines
N/A
Examples
moxa (config-if)# qos rate-limit-type simple-token-bucket cir 500 cbs 2000
conform-action remark-dscp 50 violate-action drop
Error Messages
'Invalid: {} is greater than the maximum of {}'.format(pre_m_obj['meterCirValue'],
max_rate)
'Invalid: {} is greater than the maximum of {}'.format(pre_m_obj['shaperCirValue'],
max_rate)
'Invalid: {} is greater than the maximum of {}'.format(pre_m_obj['shaperCbsValue'],
max_size)
'Invalid: {} is greater than the maximum of {}'.format(pre_m_obj[key], max_size)
'Invalid: In Simple token bucket mode, when violation action is not drop, conform action
and violate action should be the same.'
Related Commands
moxa # show qos rate-limit [interface <iftype> <ifnum>]
Moxa Command Line Interface Commands
3-79
Configure Ingress Rate Limit srTCM Conform Action: None
Commands
qos rate-limit-type srtcm cir <cir(1-1000)> [cbs <cbs(1-10240)>] [ebs <ebs(1-10240)>]
conform-action none exceed-action drop violate-action drop
Syntax Description
qos
Configure QoS parameters
rate-limit-type
Configure QoS rate limit parameters
srtcm
Single Rate Three Color Marker
cir
Committed Information Rate
cir (1-1000)
Committed information rate in Mbps
cbs
Committed Burst Size
cbs (10-10240)
Committed burst size in KByte
ebs
Excess Burst Size (or PBS)
ebs (10-10240)
Excess burst size that unit of KByte
conform-action
Configure the conform action parameter
none
Do not perform any action
exceed-action
Configure the exceed action parameter
drop
Drop the packet
violate-action
Configure the violate action parameter
drop
Drop the packet
Defaults
N/A
Command Modes
Interface configuration mode
Usage Guidelines
N/A
Examples
moxa (config-if)# qos rate-limit-type srtcm cir 500 cbs 2000 ebs 2500 conform-action
none exceed-action drop violate-action drop
Error Messages
'Invalid: {} is greater than the maximum of {}'.format(pre_m_obj['meterCirValue'],
max_rate)
'Invalid: {} is greater than the maximum of {}'.format(pre_m_obj['shaperCirValue'],
max_rate)
'Invalid: {} is greater than the maximum of {}'.format(pre_m_obj['shaperCbsValue'],
max_size)
'Invalid: {} is greater than the maximum of {}'.format(pre_m_obj[key], max_size)
'Invalid: In srTCM mode, when exceed action is remark-cos, conform action should be
remark-cos and violate action should not be remark-dscp.'
'Invalid: In srTCM mode, when exceed action is remark-dscp, conform action should be
remark-dscp and violate action should not be remark-cos.'
Related Commands
moxa # show qos rate-limit [interface <iftype> <ifnum>]
Moxa Command Line Interface Commands
3-80
Configure Ingress Rate Limit srTCM Conform Action: Remark-cos
Commands
qos rate-limit-type srtcm cir <cir(1-1000)> [cbs <cbs(10-10240)>] [ebs <ebs(10-10240)>]
conform-action remark-cos <cos-priority(0-7)> exceed-action {drop | remark-cos <cos-priority(0-7)>}
violate-action {drop | remark-cos <cos-priority(0-7)>}
Syntax Description
qos
Configure QoS parameters
rate-limit-type
Configure QoS rate limit parameters
srtcm
Single Rate Three Color Marker
cir
Committed Information Rate
xir (1-1000)
Committed information rate in Mbps
cbs
Committed Burst Size
cbs (10-10240)
Committed burst size that in KByte
ebs
Excess Burst Size (or PBS)
ebs (10-10240)
Excess burst size in KByte
conform-action
Configure the conform action parameter
remark-cos
Remark the packet CoS priority
cos-priority (0-7)
The VLAN priority value
exceed-action
Configure the exceed action parameter
drop
Drop the packet
remark-cos
Remark the packet CoS priority
cos-priority (0-7)
The VLAN priority value
violate-action
Configure the violate action parameter
drop
Drop the packet
remark-cos
Remark the packet CoS priority
cos-priority (0-7)
The VLAN priority value
Defaults
N/A
Command Modes
Interface configuration mode
Usage Guidelines
N/A
Examples
moxa (config-if)# qos rate-limit-type srtcm cir 500 cbs 2000 ebs 2500 conform-action
remark-cos 7 exceed-action drop violate-action drop
Error Messages
'Invalid: {} is greater than the maximum of {}'.format(pre_m_obj['meterCirValue'],
max_rate)
'Invalid: {} is greater than the maximum of {}'.format(pre_m_obj['shaperCirValue'],
max_rate)
'Invalid: {} is greater than the maximum of {}'.format(pre_m_obj['shaperCbsValue'],
max_size)
'Invalid: {} is greater than the maximum of {}'.format(pre_m_obj[key], max_size)
'Invalid: In srTCM mode, when exceed action is remark-cos, conform action should be
remark-cos and violate action should not be remark-dscp.'
'Invalid: In srTCM mode, when exceed action is remark-dscp, conform action should be
remark-dscp and violate action should not be remark-cos.'
Related Commands
moxa # show qos rate-limit [interface <iftype> <ifnum>]
Moxa Command Line Interface Commands
3-81
Configure Ingress Rate Limit srTCM Conform Action: Remark-dscp
Commands
qos rate-limit-type srtcm cir <cir(1-1000)> [cbs <cbs(10-10240)>] [ebs <ebs(10-10240)>]
conform-action remark-dscp <dscp-priority(0-63)> exceed-action {drop | remark-dscp
<dscp-priority(0-63)>} violate-action {drop | remark-dscp <dscp-priority(0-63)>}
Syntax Description
qos
Configure QoS parameters
rate-limit-type
Configure QoS rate limit parameters
srtcm
Single Rate Three Color Marker
cir
Committed Information Rate
cir (1-1000)
Committed information rate in Mbps
cbs
Committed Burst Size
cbs (10-10240)
Committed burst size in KByte
ebs
Excess Burst Size (or PBS)
ebs (10-10240)
Excess burst size that in KByte
conform-action
Configure the conform action parameter
remark-cos
Remark the packet CoS priority
dscp-priority (0-7)
Differentiated Services Code Point(DSCP) value
exceed-action
Configure the exceed action parameter
drop
Drop the packet
remark-cos
Remark the packet CoS priority
dscp-priority (0-7)
The Differentiated Services Code Point (DSCP) value
violate-action
Configure the violate action parameter
drop
Drop the packet
remark-cos
Remark the packet CoS priority
<dscp-priority(0-7)>
The Differentiated Services Code Point (DSCP) value
Defaults
N/A
Command Modes
Interface configuration mode
Usage Guidelines
N/A
Examples
moxa (config-if)# qos rate-limit-type srtcm cir 500 cbs 2000 ebs 2500 conform-action
remark-cos 7 exceed-action drop violate-action drop
Error Messages
'Invalid: {} is greater than the maximum of {}'.format(pre_m_obj['meterCirValue'],
max_rate)
'Invalid: {} is greater than the maximum of {}'.format(pre_m_obj['shaperCirValue'],
max_rate)
'Invalid: {} is greater than the maximum of {}'.format(pre_m_obj['shaperCbsValue'],
max_size)
'Invalid: {} is greater than the maximum of {}'.format(pre_m_obj[key], max_size)
'Invalid: In srTCM mode, when exceed action is remark-cos, conform action should be
remark-cos and violate action should not be remark-dscp.'
'Invalid: In srTCM mode, when exceed action is remark-dscp, conform action should be
remark-dscp and violate action should not be remark-cos.'
Related Commands
moxa # show qos rate-limit [interface <iftype> <ifnum>]
Moxa Command Line Interface Commands
3-82
Show Ingress Rate Limit Parameters
Commands
show qos rate-limit [interface <iftype> <ifnum>]
Syntax Description
show
Display configuration/status information
qos
Display QoS information
rate-limit
Display QoS rate limit information
interface
Interface information
iftype
The interface type
ifnum
The interface index
Defaults
N/A
Command Modes
Privileged EXEC Mode
Usage Guidelines
N/A
Examples
moxa # show qos rate-limit interface ethernet 1/1
QoS Rate Limit Statue of Interface Ethernet 1/1
--------------------------------------------
Meter Type : Simple Token Bucket
CIR : Disable
CBS : Disable
EBS : Disable
Color Mode : Blind
Confirm Action : None
Remark CoS Value : None
Remark DSCP Value : None
Exceed Action : Drop
Remark CoS Value : None
Remark DSCP Value : None
Violate Action : Drop
Remark CoS Value : None
Remark DSCP Value : None
moxa # show qos rate-limit
QoS Rate Limit Statue of Interface Ethernet 1/1
--------------------------------------------
Meter Type : Simple Token Bucket
CIR : Disable
CBS : Disable
EBS : Disable
Color Mode : Blind
Confirm Action : None
Remark CoS Value : None
Remark DSCP Value : None
Exceed Action : Drop
Remark CoS Value : None
Remark DSCP Value : None
Violate Action : Drop
Remark CoS Value : None
Remark DSCP Value : None
QoS Rate Limit Statue of Interface Ethernet 1/2
--------------------------------------------
Moxa Command Line Interface Commands
3-83
Meter Type : Simple Token Bucket
CIR : Disable
CBS : Disable
EBS : Disable
Color Mode : Blind
……
Error Messages
N/A
Related Commands
moxa(config-if)# qos rate-limit-type {simple-token-bucket | srtcm} [cir <cir(1-1000)>]
[cbs <cbs(1-10240)>] [ebs <ebs(1-10240)>] [conform-action {none | remark-cos
<cos-priority(0-7)> | remark-dscp <dscp-priority(0-63)>}] [exceed-action {drop |
remark-cos <cos-priority(0-7)> | remark-dscp <dscp-priority(0-63)>}] [violate-action
{drop | remark-cos <cos-priority(0-7)> | remark-dscp <dscp-priority(0-63)>}]
Scheduler
Configure Qos Scheduler Type Setting
Commands
qos scheduler-type {strict-priority | wrr}
Syntax Description
qos
Configure QoS parameters
scheduler-type
Configure QoS scheduler parameters
strict-priority
Strict Priority
wrr
Weighted Round Robin
Defaults
The QoS scheduler type is set to strict priority by default
Command Modes
Interface configuration mode
Usage Guidelines
N/A
Examples
moxa (config-if)# qos scheduler-type wrr
Error Messages
N/A
Related Commands
moxa # show qos scheduler [ interface <iftype> <ifnum> ]
Moxa Command Line Interface Commands
3-84
Show QoS Scheduler Setting
Commands
show qos scheduler [ interface <iftype> <ifnum> ]
Syntax Description
show
Display configuration/status information
qos
Display QoS information
scheduler
Display QoS scheduler
interface
The interface information
iftype
The interface type
ifnum
The interface index
Defaults
N/A
Command Modes
Privileged EXEC mode
Usage Guidelines
N/A
Examples
moxa # show qos scheduler interface ethernet 1/1
QoS Scheduler Algorithm
------------------------------------------------------
Interface Ethernet 1/1 Scheduler Algorithm is : Strict Priority
moxa# show qos scheduler
QoS Scheduler Algorithm
------------------------------------------------------
Interface Ethernet 1/1 Scheduler Algorithm is : Strict Priority
Interface Ethernet 1/2 Scheduler Algorithm is : Strict Priority
Interface Ethernet 1/3 Scheduler Algorithm is : Strict Priority
Interface Ethernet 1/4 Scheduler Algorithm is : Strict Priority
Interface Ethernet 2/1 Scheduler Algorithm is : Strict Priority
Interface Ethernet 2/2 Scheduler Algorithm is : Strict Priority
Interface Ethernet 2/3 Scheduler Algorithm is : Strict Priority
Interface Ethernet 2/4 Scheduler Algorithm is : Strict Priority
Interface Ethernet 3/1 Scheduler Algorithm is : Strict Priority
…..
Error Messages
N/A
Related Commands
moxa (config-if)# qos scheduler-type {strict-priority | wrr}
Moxa Command Line Interface Commands
3-85
Egress Shaper
Configure Shaper Setting
Commands
qos shaper cir <cir(1-1000)> cbs <cbs(10-10240>
Syntax Description
qos
Configure QoS parameters
shaper
Configure QoS shaper parameters
cir
Committed Information Rate
cir (1-1000)
The Committed Information Rate in Kbps
cbs
Committed Burst Size
cbs (10-10240)
The Committed Burst Size in KByte
Defaults
N/A
Command Modes
Interface configuration mode
Usage Guidelines
N/A
Examples
moxa (config-if)# qos shaper cir 500 cbs 2000
Error Messages
N/A
Related Commands
moxa# show qos shaper [interface <iftype> <ifnum>]
Show Shaper Setting
Commands
show qos shaper [interface <iftype> <ifnum>]
Syntax Description
show
Display configuration/status information
qos
Display QoS information
shaper
Display QoS shaper information
interface
The interface information
iftype
The interface type
ifnum
The interface index
Defaults
N/A
Command Modes
Privileged EXEC Mode
Usage Guidelines
N/A
Examples
moxa# show qos shaper interface ethernet 1/1
QoS Shaper Statue of Interface Ethernet 1/1
--------------------------------------------
CIR : 1000
CBS : 2000
------------------------------------------------------------------------------------------------
moxa# show qos shaper
QoS Shaper Statue of Interface Ethernet 1/1
--------------------------------------------
CIR : Disable
CBS : Disable
QoS Shaper Statue of Interface Ethernet 1/2
--------------------------------------------
CIR : Disable
CBS : Disable
…..
Error Messages
N/A
Related Commands
moxa(config-if)# qos shaper cir <cir(1-1000)> cbs <cbs(10-10240)>
Moxa Command Line Interface Commands
3-86
Multicast
IGMP Snooping
Enable/disable System-based IGMP Snooping
Commands
igmp-sooping {enable | disable}
Syntax Description
igmp-snooping
Configure IGMP Snooping parameters
enable
Enable system-based IGMP Snooping
disable
Disable system-based IGMP Snooping
Defaults
N/A
Command Modes
Global Configuration
Usage Guidelines
GMRP has to be disabled in order to enable GMP snooping
Examples
moxa# configure terminal
moxa(config)# igmp-snooping enable
moxa# configure terminal
moxa(config)# igmp-snooping disable
Error Messages
'Invalid: If IGMP snooping is enabled, then GMRP must be disabled.'
'Invalid: VLAN ID cannot have duplicated data.'
'Invalid: VLAN ID must exist in the VLAN configuration.'
'Invalid: The port-channel does not exist.'
'Invalid: this port is a member port of port-channel.'
'Invalid: this port is not a member port of VLAN.'
Related Commands
moxa# show igmp-snooping globals
Configure VLAN-based IGMP Snooping
Commands
igmp-snooping
no igmp-snooping
Syntax Description
igmp-snooping
Configure IGMP Snooping parameters
no
Remove configuration/delete entry/reset to default value
Defaults
VLAN-based IGMP Snooping is disabled by default
Command Modes
Config-VLAN Mode
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# vlan 2
moxa(config-vlan)# igmp-snooping
moxa# configure terminal
moxa(config)# vlan 2
moxa(config-vlan)# no igmp-snooping
Error Messages
'Invalid: If IGMP snooping is enabled, then GMRP must be disabled.'
'Invalid: VLAN ID cannot have duplicated data.'
'Invalid: VLAN ID must exist in the VLAN configuration.'
'Invalid: The port-channel does not exist.'
'Invalid: this port is a member port of port-channel.'
'Invalid: this port is not a member port of VLAN.'
Related Commands
moxa# show igmp snooping [vlan < vlanid> ]
Moxa Command Line Interface Commands
3-87
Configure IGMP Querier Role
Commands
igmp-snooping querier
no igmp-snooping querier
Syntax Description
no
Remove configuration/delete entry/reset to default value
igmp-snooping
Configure IGMP Snooping parameters
querier
Configure the IGMP Snooping role
Defaults
By default, the switch is configured as a non-querier
Command Modes
Config-VLAN Mode
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# vlan 2
moxa(config-vlan)# igmp-snooping
moxa(config-vlan)# igmp-snooping querier
moxa# configure terminal
moxa(config)# vlan 2
moxa(config-vlan)# igmp-snooping
moxa(config-vlan)# no igmp-snooping querier
Error Messages
'Invalid: If IGMP snooping is enabled, then GMRP must be disabled.'
'Invalid: VLAN ID ca not have duplicated data.'
'Invalid: VLAN ID must exist in the VLAN configuration.'
'Invalid: The port-channel does not exist.'
'Invalid: this port is a member port of port-channel.'
'Invalid: this port is not a member port of VLAN.'
Related Commands
moxa# show igmp-snooping [vlan < vlanid> ]
Configure IGMP Snooping Version
Commands
igmp-snooping version {v1 | v2 | v3}
Syntax Description
igmp-snooping
Configure IGMP Snooping parameters
version
The operating version of the IGMP Snooping switch for a specific
VLAN
v1
Configure IGMP Snooping to Version 1
v2
Configure IGMP Snooping to Version 2
v3
Configure IGMP Snooping to Version 3
Defaults
The default IGMP Snooping version is v2
Command Modes
Config-VLAN Mode
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# vlan 2
moxa(config-vlan)# igmp-snooping
moxa(config-vlan)# igmp-snooping version v3
Error Messages
'Invalid: If IGMP snooping is enabled, then GMRP must be disabled.'
'Invalid: VLAN ID cannot have duplicated data.'
'Invalid: VLAN ID must exist in the VLAN configuration.'
'Invalid: The port-channel does not exist.'
'Invalid: this port is a member port of port-channel.'
'Invalid: this port is not a member port of VLAN.'
Related Commands
moxa# show igmp-snooping [vlan < vlanid> ]
Moxa Command Line Interface Commands
3-88
Configure IGMP Snooping General Query Interval
Commands
igmp-snooping query-interval <integer (20 - 600) second>
no igmp-snooping query-interval
Syntax Description
no
Remove configuration/delete entry/reset to default value
igmp-snooping
Configure IGMP Snooping parameters
query-interval
The interval in which the general queries are sent by the IGMP
Snooping switch when configured as a querier
integer (20-600)
The general query interval period in seconds
Defaults
The default IGMP Snooping general query interval is set to 125 seconds
Command Modes
Config-VLAN Mode
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# vlan 2
moxa(config-vlan)# igmp-snooping query-interval 200
moxa# configure terminal
moxa(config)# vlan 2
moxa(config-vlan)# no igmp-snooping query-interval
Error Messages
'Invalid: If IGMP snooping is enabled, then GMRP must be disabled.'
'Invalid: VLAN ID cannot have duplicated data.'
'Invalid: VLAN ID must exist in the VLAN configuration.'
'Invalid: The port-channel does not exist.'
'Invalid: this port is a member port of port-channel.'
'Invalid: this port is not a member port of VLAN.'
Related Commands
moxa# show igmp-snooping [vlan < vlanid> ]
Moxa Command Line Interface Commands
3-89
Assign IGMP Snooping Router Port
Commands
igmp-snooping router-port [<interface-type> <slot/port-port,slot/port,...>] [port-channel <integer>]
no igmp-snooping router-port [<interface-type> <slot/port-port,slot/port,...>] [port-channel <integer>]
Syntax Description
no
Remove configuration/delete entry/reset to default value
igmp-snooping
Configure IGMP Snooping parameters
router-port
The IGMP Snooping router port status
interface-type
The interface type
slot/port-port, slot/port,
The interface list (slot number/port ID, slot number/port
ID-port ID....)
port-channel
The port-channel interface
integer
The port-channel index
Defaults
N/A
Command Modes
Config-VLAN Mode
Usage Guidelines
IGMP snooping of VLAN must enabled
Examples
moxa# configure terminal
moxa(config)# vlan 2
moxa(config-vlan)# igmp-snooping
moxa(config-vlan)# igmp-snooping router-port ethernet 1/1-3
-----------------------------------------------------------------------------------------------
moxa# configure terminal
moxa(config)# vlan 2
moxa(config-vlan)# igmp-snooping
moxa(config-vlan)# no igmp-snooping router-port ethernet 1/1-3
Error Messages
'Invalid: If IGMP snooping is enabled, then GMRP must be disabled.'
'Invalid: VLAN ID cannot have duplicated data.'
'Invalid: VLAN ID must exist in the VLAN configuration.'
'Invalid: The port-channel does not exist.'
'Invalid: this port is a member port of port-channel.'
'Invalid: this port is not a member port of VLAN.'
Related Commands
moxa# show igmp-snooping router-port [Vlan <vlan-id/vfi-id>]
Moxa Command Line Interface Commands
3-90
Show System IGMP Snooping Information
Commands
show igmp-snooping globals
Syntax Description
show
Display configuration/status information
igmp-snooping
Display IGMP Snooping information
globals
IGMP Snooping system-based information
Defaults
N/A
Command Modes
User EXEC
Privileged EXEC
Usage Guidelines
N/A
Examples
moxa# show igmp-snooping globals
IGMP Snooping global status is enabled
Error Messages
'Invalid: If IGMP snooping is enabled, then GMRP must be disabled.'
'Invalid: VLAN ID cannot have duplicated data.'
'Invalid: VLAN ID must exist in the VLAN configuration.'
'Invalid: The port-channel does not exist.'
'Invalid: this port is a member port of port-channel.'
'Invalid: this port is not a member port of VLAN.'
Related Commands
moxa(config)# igmp-snooping {enable | disable}
Show IGMP Information of VLAN
Commands
show igmp-snooping [vlan <vlan-id/vfi-id>]
Syntax Description
show
Display configuration/status information
igmp-snooping
Display IGMP Snooping information
vlan
Protocol specific information for the VLAN
vlan-id/vfi-id
The VLAN ID range between 1-4094 and the VFI ID range between
4096-65535
Defaults
N/A
Command Modes
User EXEC
Privileged EXEC
Usage Guidelines
N/A
Examples
moxa# show igmp-snooping vlan 1
IGMP Snooping VLAN Configuration for the VLAN 1
IGMP Snooping enabled
IGMP Snooping cmoxaonfigured version V2
IGMP Snooping is configured as Non-Querier
IGMP Snooping is acting as Non-Querier
General Query Interval is 125 seconds
Startup Query Interval is 31 seconds
Startup Query Count is 2
Other Querier Present Interval is 255 seconds
Error Messages
'Invalid: If IGMP snooping is enabled, then GMRP must be disabled.'
'Invalid: VLAN ID cannot have duplicated data.'
'Invalid: VLAN ID must exist in the VLAN configuration.'
'Invalid: The port-channel does not exist.'
'Invalid: this port is a member port of port-channel.'
'Invalid: this port is not a member port of VLAN.'
Related Commands
moxa(config-vlan)# igmp-snooping
moxa(config-vlan)# igmp-snooping querier
moxa(config-vlan)# igmp-snooping version {v1 | v2 | v3}
moxa(config-vlan)# igmp-snooping query-interval <(20 - 600) second>
Moxa Command Line Interface Commands
3-91
Show IGMP Information of Forwarding Database
Commands
show igmp-snooping forwarding-database [vlan <vlan-id/vfi-id>]
Syntax Description
show
Display configuration/status information
igmp-snooping
Display IGMP Snooping information
forwarding-database
Display the forwarding database
vlan
Protocol specific information for the VLAN
vlan-id/vfi-id
The VLAN ID range between 1-4094 and the VFI ID range
between 4096-65535
Defaults
N/A
Command Modes
User EXEC
Privileged EXEC
Usage Guidelines
N/A
Examples
moxa# show igmp-snooping forwarding-database vlan1
VLAN Group Address Source Address Port List
---------- --------------------- -------------------- ------------------------------
1 12.0.0.10 227.1.1.1 Eth1/1, Eth1/3, Eth1/4
1 12.0.0.20 227.1.1.1 Eth1/1, Eth1/3, Eth1/4
1 12.0.0.30 227.1.1.1 Eth1/1, Eth1/2, Eth1/4
Error Messages
'Invalid: If IGMP snooping is enabled, then GMRP must be disabled.'
'Invalid: VLAN ID cannot have duplicated data.'
'Invalid: VLAN ID must exist in the VLAN configuration.'
'Invalid: The port-channel does not exist.'
'Invalid: this port is a member port of port-channel.'
'Invalid: this port is not a member port of VLAN.'
Related Commands
N/A
Moxa Command Line Interface Commands
3-92
Show IGMP Information of Group Membership Table
Commands
show igmp-snooping groups [Vlan <vlan-id/vfi-id>]
Syntax Description
show
Display configuration/status information
igmp-snooping
Display IGMP Snooping information
groups
The group table information
vlan
Protocol specific information for the VLAN
vlan-id/vfi-id
The VLAN ID range between 1-4094 and the VFI ID range between
4096-65535
Defaults
N/A
Command Modes
User EXEC
Privileged EXEC
Usage Guidelines
N/A
Examples
moxa# show igmp-snooping groups vlan 1
VLAN Group Address Filter Mode Port List Source Address
---------- ---------------------- ----------------- ------------ -----------------------
1 224.1.1.1 EXCLUDE Eth 1/1 192.168.127.251
Error Messages
'Invalid: If IGMP snooping is enabled, then GMRP must be disabled.'
'Invalid: VLAN ID cannot have duplicated data.'
'Invalid: VLAN ID must exisit in the VLAN configuration.'
'Invalid: The port-channel does not exist.'
'Invalid: this port is a member port of port-channel.'
'Invalid: this port is not a member port of VLAN.'
Related Commands
N/A
Moxa Command Line Interface Commands
3-93
Show IGMP Information of Router Port
Commands
show igmp-snooping router-port [vlan <vlan-id/vfi-id>]
Syntax Description
show
Display configuration/status information
igmp-snooping
Display IGMP Snooping information
router-port
The IGMP Snooping router port status
vlan
Protocol specific information for the VLAN
vlan-id/vfi-id
The VLAN ID range between 1-4094 and the VFI ID range between
4096-65535
Defaults
N/A
Command Modes
User EXEC
Privileged EXEC
Usage Guidelines
N/A
Examples
moxa# show igmp-snooping router-port
VLAN Static Router Port List
---- -----------------------
1 Eth 1/1
VLAN Dynamic Router Port List
---- ------------------------
1 Eth 1/3
Error Messages
'Invalid: If IGMP snooping is enabled, then GMRP must be disabled.'
'Invalid: VLAN ID cannot have duplicated data.'
'Invalid: VLAN ID must exist in the VLAN configuration.'
'Invalid: The port-channel does not exist.'
'Invalid: this port is a member port of port-channel.'
'Invalid: this port is not a member port of VLAN.'
Related Commands
moxa(config-vlan)# igmp-snooping router-port [<interface-type>
<slot/port-port,slot/port,...>] [port-channel <integer>]
Moxa Command Line Interface Commands
3-94
GMRP
Show Global GMRP information
Commands
show vlan device info
Syntax Description
show
Display configuration/statistics/general information
vlan device info
Display the VLAN device information
Defaults
N/A
Command Modes
Privileged EXEC Mode.
Usage Guidelines
N/A
Examples
moxa# show vlan device info
vlan device configurations
--------------------------
vlan Status : Enabled
vlan Oper status : Enabled
gvrp status : Disabled
gmrp status : Disabled
gvrp Oper status : Disabled
gmrp Oper status : Disabled
Mac-vlan Status : Disabled
Subnet-vlan Status : Disabled
Protocol-Vlan Status : Enabled
Bridge Mode : Provider Edge Bridge
Base-Bridge Mode : Vlan Aware Bridge
Traffic Classes : Enabled
vlan Operational Learning Mode : IVL
Hybrid Default Learning Mode : IVL
Version number : 1
Max Vlan id : 4158
Max supported vlans : 4160
Global mac learning status : Enabled
Filtering Utility Criteria : Enabled
Unicast mac learning limit : 768
Error Messages
N/A
Related Commands
moxa(config)# set gmrp enable
Moxa Command Line Interface Commands
3-95
Show Port GMRP Information
Commands
show vlan port config [{port <interface-id> ]
Syntax Description
show
Display configuration/statistics/general information
vlan port config
Display VLAN port configuration
port interface-id
The input port number
Defaults
N/A
Command Modes
Privileged EXEC Mode.
Usage Guidelines
N/A
Examples
moxa# show vlan port config 1/1
vlan Port configuration table
-------------------------------
Port 1-1
Bridge Port Type : Customer Bridge Port
Port Vlan ID : 1
Port Acceptable Frame Type : Admit All
Port Mac Learning Status : Enabled
Port Ingress Filtering : Disabled
Port Mode : Hybrid
Port Gvrp Status : Enabled
Port Gmrp Status : Disabled
Port Gvrp Failed Registrations : 0
Gvrp last pdu origin : 00:00:00:00:00:00
Port Restricted Vlan Registration : Disabled
Port Restricted Group Registration : Enabled
Mac Based Support : Disabled
Subnet Based Support : Disabled
Port-and-Protocol Based Support : Enabled
Default Priority : 0
Filtering Utility Criteria : Default
Port Protected Status : Disabled
Ingress EtherType : 0x8100
Egress EtherType : 0x8100
Egress TPID Type : Portbased
Allowable TPID 1 : 0x0
Allowable TPID 2 : 0x0
Allowable TPID 3 : 0x0
Reflection Status : Disabled
Error Messages
N/A
Related Commands
moxa(config)# set port gmrp enable
moxa(config-if)# group restrict enable
Moxa Command Line Interface Commands
3-96
Configure GMRP Global Setting
Commands
gmrp { enable | disable }
Syntax Description
gmrp
Configure the GMRP parameters
enable
Enable GMRP on all switch ports and automatically start the GARP
on the switch if the GARP is disabled.
disable
Disable GMRP on all switch ports.
Defaults
Global GMRP is enabled by default
Command Modes
Global Configuration Mode
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# gmrp enable
Error Messages
N/A
Related Commands
moxa# show vlan device info
Configure GMRP Port Setting
Commands
gmrp
no gmrp
Syntax Description
gmrp
Configure the GMRP parameters
Defaults
GMRP is enabled by default
Command Modes
Interface Configuration Mode
Usage Guidelines
N/A
Examples
moxa# interface ethernet 1/1
moxa(config-if)# no gmrp
Error Messages
N/A
Related Commands
moxa# show vlan port config
Configure GMRP Group Restricted Setting
Commands
group restricted {enable | disable }
Syntax Description
group restricted
Configure the restricted group registration on a specified port
enable
Enable restricted group registration on the port
disable
Disable restricted group registration on the port
Defaults
GMRP group restriction is disabled by default
Command Modes
Interface Configuration Mode
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# interface ethernet 1/1
moxa(config-if)# group restricted
Error Messages
Wrong interface type for port
Related Commands
moxa# show vlan port config
Moxa Command Line Interface Commands
3-97
Static Multicast
Show MAC Address Table for Static Multicast
Commands
show mac-address-table static multicast [vlan <vlan-range>] [address
<aa:aa:aa:aa:aa:aa>][{interface {port-channel <integer> | <interface-type> <interface-id>]
Syntax Description
mac-address-table
Display the MAC address table information
static multicast
Display static multicast address information
vlan <vlan-range>
Display all entries in the FDB table for the specified
VLANs
address <aa:aa:aa:aa:aa:aa>
Display the specified multicast MAC address in the
FDB table
Interface
<interface-type> <interface-id> /
Port-channel <integer>
Display all specified interface entries in the FDB
table
Defaults
N/A
Command Modes
Privileged EXEC
User EXEC
Usage Guidelines
Display static multicast address table
Examples
moxa# show mac-address-table static multicast
Static Multicast Table
----------------------
Vlan : 1
Mac Address : 01:02:03:04:05:06
Member Ports : Eth1/1
Forbidden Ports : Eth1/2
Status : Permanent
------------------------------------------------
Total Mac Addresses displayed: 1
Error Messages
N/A
Related Commands
mac-address-table static multicast
Moxa Command Line Interface Commands
3-98
Configure MAC Address Table for Static Multicast
Commands
mac-address-table static multicast <aa:aa:aa:aa:aa:aa> vlan <vlan-id> {add | set} interface
[<interface-type> <slot/port-port,slot/port,...>] [port-channe l <integer>] [forbidden-ports
[<interface-type> <slot/port-port,slot/port,...>] [port-channel <integer>]] [status permanent]
Syntax Description
mac-address-table
Configure the MAC address table
static multicast
Configure the static multicast address
aa:aa:aa:aa:aa:aa
The multicast destination MAC address
vlan <vlan-id>
The VLAN ID of the VLAN the multicast destination MAC
address belongs to
add
Add the new interface port and forbidden port.
Set
Overwrite the new interface port and forbidden port
interface
Configure member ports details.
forbidden-ports
Configure the set of ports to which frames destined for a
specific multicast MAC address must not be forwarded, such
as from GMRP.
status
The status of the static multicast entry.
permanent
Entry remains even after the next reset of the bridge
Defaults
N/A
Command Modes
Privileged EXEC
Global Configuration
Usage Guidelines
Configure the static multicast address
Examples
moxa(config)# mac-address-table static multicast 01:02:03:04:05:06 vlan 1 add
interface ethernet 1/1-2 forbidden-ports ethernet 2/1-2
Error Messages
"Invalid: Duplicate MAC Address."
"Invalid: Configuration fail."
"Invalid: The port is not included in VLAN egress ports."
"Invalid: The MAC+VID entry must be removed from Port Security first."
"Invalid: The port must remove from port security."
"Invalid: Reserved multicast address (01:80:C2) is not allowed to set static multicast."
"Invalid: Egress Ports and Forbidden Ports are overlapping."
Related Commands
show mac-address-table static multicast
Moxa Command Line Interface Commands
3-99
Network Redundancy
Layer 2 Redundancy
Spanning Tree
Enable/Disable Spanning Tree
Commands
spanning-tree
no spanning-tree
Syntax Description
no
Disable the configuration/delete the entry/reset to default value
spanning-tree
Configure Spanning Tree Protocol parameters
Defaults
Spanning Tree Protocol is disabled by default
Command Modes
Interface Configuration
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# interface ethernet 1/1
moxa(config-if)# spanning-tree
moxa(config-if)# no spanning-tree
Error Messages
Invalid: Port channel member port cannot be assigned to a redundant protocol.
Invalid: Redundant Protocol and Port Security cannot be enabled on the same port.
Invalid: Redundant Protocol and 802.1x/MAB cannot be enabled on the same port.
Invalid: The port-channel group does not exist.
Related Commands
show spanning-tree detail
show spanning-tree summary
Configure Spanning Tree Compatibility
Commands
spanning-tree compatibility { stp | rstp }
no spanning-tree compatibility
Syntax Description
no
Disable the configuration/delete the entry/resets to default value
spanning-tree
Configure Spanning Tree Protocol parameters
compatibility
The Spanning Tree compatibility version
stp
Spanning Tree Protocol configuration
rstp
Rapid Spanning Tree configuration
Defaults
Spanning Tree Protocol compatibility is set to rstp by default.
Command Modes
Global Configuration
Usage Guidelines
The “no spanning-tree compatibility” command will restore the default value
Examples
moxa# configure terminal
moxa(config)# spanning-tree compatibility stp
moxa(config)# spanning-tree compatibility rstp
moxa(config)# no spanning-tree compatibility
Error Messages
N/A
Related Commands
show spanning-tree
show spanning-tree detail
Moxa Command Line Interface Commands
3-100
Configure Spanning Tree Priority
Commands
spanning-tree priority <value (0-61440)>
no spanning-tree priority
Syntax Description
no
Disable the configuration / deletes the entry / resets to default
value
spanning-tree
Configure Spanning Tree Protocol parameters
priority
Configure switch priority for Spanning Tree instances
value
The switch priority value ranging from 0 to 61440
Defaults
The default priority is set to 32768
Command Modes
Global Configuration
Usage Guidelines
The “no spanning-tree priority” command will restore the default value
Examples
moxa# configure terminal
moxa(config)# spanning-tree priority 61440
moxa(config)# no spanning-tree priority
Error Messages
N/A
Related Commands
show spanning-tree
show spanning-tree detail
Configure Spanning Tree Forward Time
Commands
spanning-tree forward-time <seconds (4-30)>
no spanning-tree forward-time
Syntax Description
no
Disable the configuration/deletes the entry/resets to default value
spanning-tree
Configure Spanning Tree Protocol parameters
forward-time
The interval (in seconds) in which a port stays in its current state
before moving to next state
seconds
The forwarding time ranging from 4 to 30 seconds
Defaults
The default forwarding time is 15 seconds
Command Modes
Global Configuration
Usage Guidelines
Command “no spanning-tree forward-time” will reset to default value
2*(ForwardDelay -1)>=MaxAge >= 2*(Hello Time + 1)
Examples
moxa# configure terminal
moxa(config)# spanning-tree forward-time 16
moxa(config)# no spanning-tree forward-time
Error Messages
% RSTP: 2*(Forward time -1)>=Max age time >= 2*(Hello time + 1)
Related Commands
show spanning-tree
show spanning-tree detail
Moxa Command Line Interface Commands
3-101
Configure Spanning Tree Hello Time
Commands
spanning-tree hello-time <seconds (1-2)>
no spanning-tree hello-time
Syntax Description
no
Disable the configuration/deletes the entry/resets to default value
spanning-tree
Configure Spanning Tree Protocol parameters
hello-time
The interval (in seconds) between the transmission of configuration
BPDUs
seconds
The hello time interval ranging from 1 to 2 seconds
Defaults
The default hello time is set to 2 seconds
Command Modes
Global Configuration
Usage Guidelines
The “no spanning-tree hello-time” command will restore the default value
2*(ForwardDelay -1)>=MaxAge >= 2*(Hello Time + 1)
Examples
moxa# configure terminal
moxa(config)# spanning-tree hello-time 1
moxa(config)# no spanning-tree hello-time
Error Messages
% RSTP: 2*(Forward time -1)>=Max age time >= 2*(Hello time + 1)
Related Commands
show spanning-tree
show spanning-tree detail
Configure Spanning Tree Maximum Age
Commands
spanning-tree max-age <seconds (6-40)>
no spanning-tree max-age
Syntax Description
no
Disable the configuration/delete the entry/reset to default value
spanning-tree
Configure Spanning Tree Protocol parameters
max-age
The maximum age (in seconds) before learnt STP information is
discarded
seconds
The maximum age ranging from 6 to 40 seconds
Defaults
The STP maximum age is set to 20 seconds by default
Command Modes
Global Configuration
Usage Guidelines
The “no spanning-tree max-age” command will restore the default value
2*(ForwardDelay -1)>=MaxAge >= 2*(Hello Time + 1)
Examples
moxa# configure terminal
moxa(config)# spanning-tree max-age 21
moxa(config)# no spanning-tree max-age
Error Messages
% RSTP: 2*(Forward time -1)>=Max age time >= 2*(Hello time + 1)
Related Commands
show spanning-tree
show spanning-tree detail
Moxa Command Line Interface Commands
3-102
Configure Spanning Tree Transmission Hold Counter
Commands
spanning-tree transmit hold-count <value (1-10)>
no spanning-tree transmit hold-count
Syntax Description
no
Disable the configuration/delete the entry/reset to default value
spanning-tree
Configure Spanning Tree Protocol
transmit
Transmission hold counter configuration
hold-count
Configure the hold counter to limit the maximum transmission rate
of the switch
value
The transmission hold counter value ranging from 1 to 10
Defaults
The STP hold counter is set to 6 by default
Command Modes
Global Configuration
Usage Guidelines
The “no spanning-tree transmit hold-count” command will restore the default value
Examples
moxa# configure terminal
moxa(config)# spanning-tree transmit hold-count 10
moxa(config)# no spanning-tree transmit hold-count
Error Messages
N/A
Related Commands
show spanning-tree detail
Configure Spanning Tree Auto-ea dge
Commands
spanning-tree auto-edge
no spanning-tree auto-edge
Syntax Description
no
Disable the configuration/delete the entry/reset to default value
spanning-tree
Configure Spanning Tree Protocol
auto-edge
Configure the automatic detection of bridges attached to an
interface
Defaults
Spanning Tree auto-edge is enabled by default
Command Modes
Interface Configuration
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# interface ethernet 1/1
moxa(config-if)# spanning-tree auto-edge
moxa(config-if)# no spanning-tree auto-edge
Error Messages
N/A
Related Commands
show spanning-tree detail
show spanning-tree interface ethernet 1/1 detail
Moxa Command Line Interface Commands
3-103
Configure Spanning Tree Cost
Commands
spanning-tree cost <value (0-200000000)>
no spanning-tree cost
Syntax Description
no
Disable the configuration/delete the entry/reset to default value
spanning-tree
Configure Spanning Tree Protocol
cost
Configure the path cost
value
The Spanning Tree cost ranging from 0 to 200000000
Defaults
The default path cost is set to 0
Command Modes
Interface Configuration
Usage Guidelines
The “spanning-tree cost 0” command will auto-detect the cost based on port speed
The “no spanning-tree cost” command will restore the default value
Examples
moxa# configure terminal
moxa(config)# interface ethernet 1/1
moxa(config-if)# spanning-tree cost 20000
moxa(config-if)# no spanning-tree cost
Error Messages
N/A
Related Commands
show spanning-tree detail
show spanning-tree interface ethernet 1/1 detail
show spanning-tree interface ethernet 1/1 detail
Configure Spanning Tree Link Type
Commands
spanning-tree link-type { point-to-point | shared }
no spanning-tree link-type
Syntax Description
no
Disable the configuration/delete the entry/reset to default value
spanning-tree
Configure Spanning Tree Protocol parameters
link-type
Configure the link type as a point-to-point link or as a shared LAN
segment on which another bridge is present
point-to-point
Set the link a a point-to-point link
shared
Set the link as a shared link
Defaults
The default Spanning Tree link-type is set to auto-detect
Command Modes
Interface Configuration
Usage Guidelines
The “no spanning-tree link-type” command will auto-detect the interface link type based
on the port duplex mode
Examples
moxa# configure terminal
moxa(config)# interface ethernet 1/1
moxa(config-if)# spanning-tree link-type point-to-point
moxa(config-if)# spanning-tree link-type shared
moxa(config-if)# no spanning-tree link-type
Error Messages
N/A
Related Commands
show spanning-tree detail
show spanning-tree interface ethernet 1/1
show spanning-tree interface ethernet 1/1 detail
Moxa Command Line Interface Commands
3-104
Configure Spanning Tree Portfast
Commands
spanning-tree portfast
no spanning-tree portfast
Syntax Description
no
Disable the configuration/delete the entry/reset to default value
spanning-tree
Configure Spanning Tree Protocol parameters
portfast
Specify ports that have only hosts connected to enable immediate
transition to a forwarding state
Defaults
Spanning Tree Portfast is disabled by default
Command Modes
Interface Configuration
Usage Guidelines
Shut down the interface before enabling the Portfast function
The Portfast function cannot be enabled on a port that has loop guard enabled
Examples
moxa# configure terminal
moxa(config)# interface ethernet 1/1
moxa(config-if)# spanning-tree portfast
moxa(config-if)# no spanning-tree portfast
Error Messages
N/A
Related Commands
show spanning-tree detail
show spanning-tree interface ethernet 1/1
show spanning-tree interface ethernet 1/1 detail
Configure Spanning Tree Port Priority
Commands
spanning-tree port-priority <value (0-240)>
no spanning-tree port-priority
Syntax Description
no
Disable the configuration/delete the entry/reset to default value
spanning-tree
Configure Spanning Tree Protocol parameters
port-priority
Configure the port priority value
value
The Spanning Tree port priority ranging from 0 to 240
Defaults
The default Spanning Tree port priority is set to 128
Command Modes
Interface Configuration
Usage Guidelines
The “no spanning-tree port-priority” command will restore the default value
Examples
moxa# configure terminal
moxa(config)# interface ethernet 1/1
moxa(config-if)# spanning-tree port-priority 16
moxa(config-if)# no spanning-tree port-priority
Error Messages
N/A
Related Commands
show spanning-tree detail
show spanning-tree interface ethernet 1/1
show spanning-tree interface ethernet 1/1 detail
Moxa Command Line Interface Commands
3-105
Configure Spanning Tree BPDU Guard
Commands
spanning-tree bpduguard
no spanning-tree bpduguard
Syntax Description
no
Disable the configuration/delete the entry/reset to default value
spanning-tree
Configure Spanning Tree Protocol parameters
bpduguard
Configures an interface to transition into the error-disabled state
when it receives a BPDU
Defaults
Spanning Tree BPDU guard is disabled by default
Command Modes
Interface Configuration
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# interface ethernet 1/1
moxa(config-if)# spanning-tree bpduguard
moxa(config-if)# no spanning-tree bpduguard
Error Messages
N/A
Related Commands
show spanning-tree detail
show spanning-tree interface gigabitethernet 0/1 bpduguard
show spanning-tree interface gigabitethernet 0/1 detail
Configure Spanning Tree BPDU Filter
Commands
spanning-tree bpdufilter
no spanning-tree bpdufilter
Syntax Description
no
Disable the configuration/delete the entry/reset to default value
spanning-tree
Configure Spanning Tree Protocol parameters
bpdufilter
Configure BPDU filtering
Defaults
Spanning Tree BPDU filtering is disabled by default
Command Modes
Interface Configuration
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# interface ethernet 1/1
moxa(config-if)# spanning-tree bpdufilter
moxa(config-if)# no spanning-tree bpdufilter
Error Messages
N/A
Related Commands
show spanning-tree detail
show spanning-tree interface ethernet 1/1
show spanning-tree interface ethernet 1/1 detail
Moxa Command Line Interface Commands
3-106
Configure Spanning Tree Root Guard
Commands
spanning-tree rootguard
no spanning-tree rootguard
Syntax Description
no
Disable the configuration/delete the entry/reset to default value
spanning-tree
Configure Spanning Tree Protocol parameters
rootguard
Configure restricted forwarding on an interface
Defaults
Spanning Tree root guard is disabled by default
Command Modes
Interface Configuration
Usage Guidelines
The Root guard function cannot be enabled on a port that has loop guard enabled
Examples
moxa# configure terminal
moxa(config)# interface ethernet 1/1
moxa(config-if)# spanning-tree rootguard
moxa(config-if)# no spanning-tree rootguard
Error Messages
% RSTP: loopGuard and rootGuard should be exclusive
Related Commands
show spanning-tree detail
show spanning-tree interface ethernet 1/1
show spanning-tree interface ethernet 1/1 detail
Configure Spanning Tree Loop Guard
Commands
spanning-tree loopguard
no spanning-tree loopguard
Syntax Description
no
Disable the configuration/delete the entry/reset to default value
spanning-tree
Configure Spanning Tree Protocol parameters
loopguard
Configure restricted forwarding on an interface
Defaults
Spanning Tree loop guard is disabled by default
Command Modes
Interface Configuration
Usage Guidelines
The loop guard function cannot be enabled on a port that has portfast enabled
The loop guard function cannot be enabled on a port that has root guard enabled
Examples
moxa# configure terminal
moxa(config)# interface ethernet 1/1
moxa(config-if)# spanning-tree loopguard
moxa(config-if)# no spanning-tree loopguard
Error Messages
% RSTP: loopGuard and rootGuard should be exclusive
Related Commands
show spanning-tree detail
show spanning-tree interface ethernet 1/1
show spanning-tree interface ethernet 1/1 detail
Moxa Command Line Interface Commands
3-107
Configure Spanning Tree Errordisabled Recovery Interval
Commands
spanning-tree errordisable recovery-interval <second (30-65535)>
no spanning-tree errordisable recovery-interval
Syntax Description
no
Disable the configuration/delete the entry/reset to default
value
spanning-tree
Configure Spanning Tree Protocol
errordisable
Configure the error-disable timer
recovery-interval
The interval (in seconds) for a port to recover from
error-disabled state
second
The errordisabled recovery interval ranging from 30 to 65535
seconds
Defaults
The default error-disabled recovery interval is set to 300 seconds
Command Modes
Global Configuration
Usage Guidelines
N/A
Examples
moxa(config)# spanning-tree errordisable recovery-interval 30
Error Messages
N/A
Related Commands
show spanning-tree detail
Clear Spanning Tree Detected Protocols
Commands
clear spanning-tree detected protocols interface { <interface-id> | port-channel <integer> }
Syntax Description
clear
Clear the configuration
spanning-tree
Configure Spanning Tree Protocol parameters
detected
Spanning Tree detected protocols
protocols
Spanning Tree detected protocols
interface
Configure the interface
interface-id
The interface ID
port-channel
The port channel
Defaults
N/A
Command Modes
User EXEC mode
Usage Guidelines
N/A
Examples
moxa# clear spanning-tree detected protocols interface ethernet 1/1
moxa# clear spanning-tree detected protocols interface port-channel 1
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-108
Show Spanning Tree Bridge Information
Commands
show spanning-tree bridge
Syntax Description
show
Display the Configuration/statistics/general information
spanning-tree
Spanning Tree-related information
bridge
Spanning Tree bridge information
Defaults
N/A
Command Modes
User EXEC Mode
Usage Guidelines
N/A
Examples
moxa# show spanning-tree bridge
Bridge ID HelloTime MaxAge FwdDly Protocol
----------- --------- -------- -------- ----------
80:00:00:01:02:03:04:05 2 sec 20 sec 15 sec rstp
moxa#
Error Messages
N/A
Related Commands
N/A
Show Spanning Tree Root Information
Commands
show spanning-tree root
Syntax Description
show
Display the configuration/statistics/general information
spanning-tree
Spanning Tree-related information
root
Spanning Tree root information
Defaults
N/A
Command Modes
User EXEC Mode
Usage Guidelines
N/A
Examples
moxa# show spanning-tree root
Root ID RootCost MaxAge FwdDly RootPort
--------- ----------- -------- -------- -----------
00:00:00:00:00:00:00:00 0 sec 20 sec 15 sec 0
moxa#
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-109
Show Spanning Tree Interface Information
Commands
show spanning-tree interface { ethernet <slot/port> | port-channel <id> }
show spanning-tree interface { ethernet <slot/port> | port-channel <id> } detail
show spanning-tree interface { ethernet <slot/port> | port-channel <id> } inconsistency
Syntax Description
show
Display the configuration/statistics/general information
spanning-tree
Spanning Tree-related information
interface
Spanning Tree interface information
ethernet <slot/port>
The Ethernet slot or port number
port-channel <id>
The port channel ID
detail
Detailed information about the port and bridge
inconsistency
Spanning Tree inconsistent state information
Defaults
N/A
Command Modes
User EXEC Mode
Usage Guidelines
N/A
Examples
moxa# show spanning-tree interface ethernet 1/2
moxa# show spanning-tree interface ethernet 1/2 inconsistency
moxa# show span in eth 1/1
Root State Cost Prio Type
----------- ----- ----- ----- -----
Disabled Disable 200000000 128 SharedLAN
moxa# show span in eth 1/1 incon
BPDU Inconsist: False
Root Inconsist: False
Loop Inconsist: False
moxa#
Error Messages
N/A
Related Commands
N/A
Show Spanning Tree Details
Commands
show spanning-tree [detail]
show spanning-tree active [detail]
Syntax Description
show
Display the configuration/statistics/general information
spanning-tree
Spanning Tree related information
detail
Detailed Spanning Tree information
active
Spanning Tree information of active ports
Defaults
N/A
Command Modes
User EXEC Mode
Usage Guidelines
N/A
Examples
moxa# show spanning-tree
Root ID Priority 0
Address 00:00:00:00:00:00
Cost 0
Port 0
Max Age 20 sec
Forward Delay 15 sec
Moxa Command Line Interface Commands
3-110
Hello Time 2 sec
Spanning tree Protocol has been disabled
Bridge ID Priority 32768
Address 00:01:02:03:04:05
Hello Time 2 sec
Max Age 20 sec
Forward Delay 15 sec
Port Enable Role State Cost Prio Type
Eth1/1 Disabled Disabled Disabled 200000000 128 SharedLan
Eth1/2 Disabled Disabled Disabled 200000000 128 SharedLan
Eth1/3 Disabled Disabled Disabled 200000000 128 SharedLan
Eth1/4 Disabled Disabled Disabled 200000000 128 SharedLan
moxa# show spanning-tree detail
Spanning tree Protocol has been disabled
Bridge Identifier has priority 32768, Address 00:01:02:03:04:05
Configured Hello time 2 sex, Max Age 20 sec
Forward Delay 15 sec
Number of Topology Changes 0
Time since topology Change 0 seconds ago
Transmit Hold-Count 6
Root Times:Max Age 20 sec Forward Delay 15 sec
Hello Time 2 sec
Port 1 [Eth1/1] is Disabled, Disabled
Port PathCost 200000000, Port Priority 128, Port Identifier 128.1
Designated Root has priority 0, address 00:00:00:00:00:00
Designated Port Id is 0.0, Designated PathCost 0
No of Transition to forwarding State :0
Auto-Edge is disabled
PortFast is enabled, Oper-Edge is disabled
BPDU Filtering is disabled.
BPDU Guard is enabled.
Root Guard is disabled.
Loop Guard is disabled.
Admin LinkType is Auto, Oper LinkType is Shared-Lan
BPDUs : sent 0 , received 0
Timers: Hello - 0, Forward Delay - 0, Topology Change - 0,
Error Disabled Recovery Interval 300 sec
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-111
Turbo Ring v2
Show Turbo Ring v2 Status
Commands
show turbo-ring-v2 { config | status }
Syntax Description
show
Display configuration/statistics/general information
turbo-ring-v2
Display Turbo Ring v2 information
config
Ring configuration information
status
Ring status information
Defaults
N/A
Command Modes
User EXEC/Privileged EXEC
Usage Guidelines
N/A
Examples
moxa# show turbo-ring-v2 config
Turbo Ring V2 Module is enabled
Ring 1:
Enable: enabled
Set as master: disabled
1st port: Eth1/1
2nd port: Eth1/2
Ring 2:
Enable: disabled
Set as master: disabled
1st port: Eth1/3
2nd port: Eth1/4
Coupling:
Enable: disabled
Mode: Ring coupling(primary)
Coupling Port: Eth2/1
moxa# show turbo-ring-v2 status
Turbo Ring V2 status:
Ring 1:
Status: Healthy
Master/Slave: Master
Master ID: 00:90:e8:00:bb:cc
1st Ring Port Status: Eth1/1 Forwarding
2nd Ring Port Status: Eth1/2 Blocked
Ring 2:
Status:---
Master/Slave:---
Master ID: 00:00:00:00:00:00
1st Ring Port Status:---
2nd Ring Port Status:---
Coupling:
Mode:---
Coupling Port: ---
Error Messages
N/A
Related Commands
turbo-ring-v2
Moxa Command Line Interface Commands
3-112
Configure Redundancy Mode Setting
Commands
turbo-ring-v2 { enable | disable }
Syntax Description
turbo-ring-v2
Configure Turbo Ring V2 parameters
enable
Enable Turbo Ring V2
disable
Disable Turbo Ring V2
Defaults
Turbo Ring V2 is disabled by default
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
moxa(config)# turbo-ring-v2 enable
Error Messages
Invalid: A maximum of two redundant protocols can be enabled.
Invalid: Turbo Chain and Turbo Ring V2 cannot be enabled at the same time.
Invalid: Two redundant protocols cannot use the same port.
Invalid: Turbo Ring V2 and STP/RSTP cannot be enabled at the same time.
Related Commands
show turbo-ring-v2 config
Configure Ring Settings
Commands
turbo-ring-v2 ring-id primary interface { port-channel <integer (1-65535)> | <interface-type>
<interface-id> } secondary interface { port-channel <integer (1-65535)> | <interface-type>
<interface-id> }
no turbo-ring-v2 ring-id
Syntax Description
no
Remove configuration/delete entry/reset to default value
turbo-ring-v2
Configure Turbo Ring V2 parameters
ring-id
Configure the ring ID (1-2)
primary
The first ring port
interface
The port interface
interface-type
Ethernet
interface-id
The slot number/port number <1-7>/<1-4>
port-channel
The port channel interface
secondary
The second ring port
interface
The port interface
interface-type
Ethernet
interface-id
The slot number/port number <1-7>/<1-4>
port-channel
The port channel interface
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
At least one turbo ring domain or coupling must be enabled. Two turbo ring domains and
coupling cannot be enabled at the same time.
Examples
moxa(config)# turbo-ring-v2 1 primary interface ethernet 2/1 secondary interface
ethernet 2/2
Error Messages
Invalid: The first and second ring ports cannot be on the same port.
Invalid: A ring port cannot belong to both rings.
Invalid: A port channel must be created first to be able to assign to a ring port.
Related Commands
show turbo-ring-v2 { config | status }
Moxa Command Line Interface Commands
3-113
Configure the Switch as the Ring Master
Commands
turbo-ring-v2 ring-id master
no turbo-ring-v2 ring-id master
Syntax Description
no
Remove configuration/delete entry/reset to default value
turbo-ring-v2
Configure Turbo Ring V2 parameters
ring-id
Configure the ring ID (1-2)
master
Enable ring master
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
moxa(config)# turbo-ring-v2 1 master
master - Set turbo ring v2 ring id as master
Error Messages
N/A
Related Commands
show turbo-ring-v2 { config | status }
Configure the Primary Port of Ring Coupling
Commands
turbo-ring-v2 coupling primary interface <interface-type> <interface-id>
no turbo-ring-v2 coupling
Syntax Description
no
Remove configuration/delete entry/reset to default value
turbo-ring-v2
Configure Turbo Ring V2 parameters
coupling
Configure ring coupling parameters
primary
Coupling primary mode
interface
The port interface
interface-type
Ethernet
interface-id
The slot number/port number <1-7>/<1-4>
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
At least one turbo ring domain or coupling must be enabled. Two turbo ring domains and
coupling cannot be enabled at the same time.
Examples
moxa(config)# turbo-ring-v2 coupling primary interface ethernet 2/1
Error Messages
Invalid: Ring coupling cannot be enabled when both rings are enabled.
Invalid: There can be one ring enabled if you want to enable ring coupling.
Invalid: A ring coupling port cannot be an active ring port.
Related Commands
show turbo-ring-v2
Moxa Command Line Interface Commands
3-114
Configure Backup Port of Ring Coupling
Commands
turbo-ring-v2 coupling backup interface <interface-type> <interface-id>
no turbo-ring-v2 coupling
Syntax Description
turbo-ring-v2
Configure Turbo Ring V2 parameters
coupling
Configure ring coupling parameters
backup
Coupling backup mode
interface
The port interface
interface-type
Ethernet
interface-id
The slot number/port number <1-7>/<1-4>
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
At least one turbo ring domain or coupling must be enabled. Two turbo ring domains and
coupling cannot be enabled at the same time.
Examples
moxa(config)# turbo-ring-v2 coupling backup interface ethernet 2/1
Error Messages
Invalid: Ring coupling cannot be enabled when both rings are enabled.
Invalid: There can be one ring enabled if you want to enable ring coupling.
Invalid: A ring coupling port cannot be an active ring port.
Related Commands
show turbo-ring-v2 { config | status }
Turbo Chain
Show Turbo Chain Information
Commands
show turbo-chain
Syntax Description
show
Display configuration/statistics/general information
turbo-chain
Display Turbo Chain information
Defaults
N/A
Command Modes
Privileged EXEC
Usage Guidelines
N/A
Examples
moxa# show turbo-chain
Admin Status: Disabled
Role: Member
Port Role Port Number Port State
------------ ----------- ----------
Member Port Eth1/1 ---
Member Port Eth1/2 ---
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-115
Configure Turbo Chain Setting
Commands
turbo-chain { enable | disable }
turbo-chain role { head | member | tail } primary interface { port-channel <port-channel-id (1-65535)>
| <interface-type> <interface-id> } secondary interface { port-channel <port-channel-id (1-65535)> |
<interface-type> <interface-id> }
Syntax Description
turbo-chain
Configure Turbo Chain parameters
enable
Enable Turbo Chain
disable
Disable Turbo Chain
role
Configure the role of the switch in the Turbo Chain
head
Set the switch as the Turbo Chain head
member
Set the switch as a Turbo Chain member
tail
Set the switch as the Turbo Chain tail
primary
Configure the Turbo Chain primary port
interface
The interface of Turbo Chain
port-channel
The port channel interface
port-channel-id
The port channel ID
interface-type
Ethernet interface
interface-id
Slot number/port number
secondary
Configure the Turbo Chain secondary port
interface
The interface of Turbo Chain
Defaults
Turbo Chain is disabled by default
Command Modes
Global Configuration
Usage Guidelines
N/A
Examples
moxa(config)# turbo-chain disable
moxa(config)# turbo-chain role member primary interface ethernet 1/1 secondary
interface ethernet 1/2
Error Messages
% Turbo Chain: Invalid: Two Identical Turbo Chain Ports.
% Turbo Chain: Invalid: The port-channel does not exist.
% Turbo Chain: Invalid: The port-channel does not exist.
% L2 Redundancy: Invalid: Two redundant protocols cannot use the same port.
% L2 Redundancy: Invalid: Port channel member port cannot be assigned to a redundant
protocol.
% L2 Redundancy: Invalid: Redundant Protocol and Port Security cannot be enabled on
the same port.
% L2 Redundancy: Invalid: Redundant Protocol and 802.1x/MAB cannot be enabled on
the same port.
% L2 Redundancy: Invalid: The port-channel group does not exist.
% L2 Redundancy: Invalid: The port-channel group is used by Turbo Ring/Turbo
Chain/Dual Homing. It cannot be deleted.
% L2 Redundancy: Invalid: A maximum of two redundant protocols can be enabled.
% L2 Redundancy: Invalid: Turbo Chain and Turbo Ring V2 cannot be enabled at the
same time.
% L2 Redundancy: Invalid: Turbo Chain and STP/RSTP cannot be enabled at the same
time.
Related Commands
show turbo-chain
Moxa Command Line Interface Commands
3-116
Dual Homing
Show Dual Homing Information
Commands
show dual-homing
Syntax Description
show
Show running system information
dual-homing
Display dual homing configurations and status
Defaults
N/A
Command Modes
Privileged EXEC/User EXEC
Usage Guidelines
N/A
Examples
moxa# show dual-homing
Status :Enabled
Connecting Redundancy Protocol: Turbo Ring v2
---------------------------------------
Path
---------------
Port-Index
-----------------
Link-Status
----------
Port-State
-----------------
Primary
Link up
Link-up
Forwarding
Secondary
Eth1/1Eth1/2
Link-down
Blocking
Error Messages
N/A
Related Commands
dual-homing
Enable/Disable Dual Homing Setting
Commands
dual-homing {enable | disable}
Syntax Description
dual-homing
Configure dual homing parameters
enable
Enable dual homing
disable
Disable dual homing
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
moxa (config)# dual-homing enable
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-117
Configure Dual Homing Path Mode
Commands
dual-homing path-mode {primary-first | maintain-current}
Syntax Description
dual-homing
Configure dual homing parameters
path-mode
Configure the dual homing path switching mode
primary-first
Primary path always first
maintain-current
Maintain the current path
Defaults
N/A
Command Modes
redundancy configuration
Usage Guidelines
N/A
Examples
moxa(config)# dual-homing path-mode primary-first
Error Messages
N/A
Command Modes
N/A
Related Commands
show dual-homing
Configure Dual Homing Primary/Secondary Interface
Commands
dual-homing primary interface {port-channel <integer (1-65535) | <interface-type> <interface-id>}
secondary interface {port-channel <integer (1-65535) | <interface-type> <interface-id>}
Syntax Description
dual-homing
Configure dual homing
primary
Configure the dual homing primary port settings
interface
Configure the dual homing port interface
secondary
Configure the dual homing secondary port settings
port-channel
Configure the port channel
Integer (1-65535)
The port channel group ID ranging from 1 to 65535
interface-type
The interface type
interface-id
The interface ID
Defaults
N/A
Command Modes
redundancy configuration
Usage Guidelines
N/A
Examples
moxa (config)# dual-homing primary interface ethernet 1/1 secondary interface
port-channel 1
Error Messages
N/A
Command Modes
N/A
Related Commands
show dual-homing
Moxa Command Line Interface Commands
3-118
Management
Network Management
SNMP
Configure SNMP Server Access Mode
Commands
snmp-server access { enable | disable | read-only }
Syntax Description
snmp-server
Configure SNMP server parameters
access
Configure the SNMP server access mode
enable
Enable SNMP server access
disable
Disable SNMP server access
read-only
Set SNMP server access to read-only mode
Defaults
SNMP server access is enabled by default
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
moxa(config)# snmp-server access enable
moxa(config)# snmp-server access disable
moxa(config)# snmp-server access read-only
Error Messages
N/A
Related Commands
snmp-server
show snmp-server
Configure SNMP Server Read-Only Community Settings
Commands
snmp-server community read-only <community-name(4-32)>
Syntax Description
snmp-server
Configure snmp-server related parameters
community
Configure the SNMP server community
read-only
Configure the SNMP server community for read-only
string (32)
The SNMP server read-only community name
Defaults
The default read-only community name is set to public
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
moxa(config)# snmp-server community read-only public
Error Messages
N/A
Related Commands
snmp-server
show snmp-server
Moxa Command Line Interface Commands
3-119
Delete SNMP Server Read-Only Community
Commands
no snmp-server community read-only
Syntax Description
no
Disable the configuration/delete the entry/reset to default value
snmp-server
Configure SNMP server parameters
community
Configure the SNMP server community
read-only
Configure the SNMP server community for read-only
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
moxa(config)# no snmp-server community read-only
Error Messages
N/A
Related Commands
snmp-server
show snmp-server
Configure SNMP Server Read-Write Community Settings
Commands
snmp-server community read-write <community-name(32)>
Syntax Description
snmp-server
Configure SNMP server parameters
community
Configure the SNMP server community
read-write
Configure the SNMP server community for read-write
string (32)
The SNMP server read-write community name
Defaults
The default read-write community name is set to private
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
moxa(config)# snmp-server community read-write private
Error Messages
N/A
Related Commands
snmp-server
show snmp-server
Configure SNMP Server Read-Write Community to Default Value
Commands
no snmp-server community read-write
Syntax Description
no
Disable the configuration/delete the entry /reset to default value
snmp-server
Configures SNMP server parameters
community
Configure the SNMP server community
read-write
Configure the SNMP server community for read-write
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
moxa(config)# no snmp-server community read-write
Error Messages
N/A
Related Commands
snmp-server
show snmp-server
Moxa Command Line Interface Commands
3-120
Configure SNMP Server Version
Commands
snmp-server version { v1-v2c-v3 | v1-v2c | v3 }
Syntax Description
snmp-server
Configure SNMP server parameters
version
Configure the SNMP server version compatibility
v1-v2c-v3
Set the SNMP server version to v1-v2c-v3
v1-v2c
Set the SNMP server version to v1-v2c
v3
Set the SNMP server version to v3-only
Defaults
The default SNMP server version is set to v1-v2c
Command Modes
Global configuration
Usage Guidelines
Set up at least one SNMP server user account before enabling v1-v2c-v3 or v3
Examples
moxa(config)# snmp-server version v1-v2c-v3
moxa(config)# snmp-server version v1-v2c
moxa(config)# snmp-server version v3
Error Messages
% Atleast setup one valid user before enable snmp-server version v1-v2c-v3 or v3
Related Commands
snmp-server
show snmp-server
Configure SNMP Server Version to Default Value
Commands
no snmp-server version
Syntax Description
no
Disable the configuration/delete the entry/reset to default value
snmp-server
Configure SNMP server parameters
version
Configure the SNMP server version compatibility
Defaults
The default SNMP server version is set to v1-v2c
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
moxa(config)# no snmp-server version
Error Messages
N/A
Related Commands
snmp-server
show snmp-server
Moxa Command Line Interface Commands
3-121
Configure SNMP Server User Account Settings
Commands
snmp-server user <user-name(32)>
authority { read-only | read-write }
auth-type { none | md5 | sha } [auth-passwd <authentication-password(64)> ] encryption
{ disable| des | aes } [encryption-key <encryption-key(64)>]
Syntax Description
snmp-server
Configure SNMP server parameters
user
Configure SNMP server user accounts
user-name (32)
The user name of the SNMP server user account
authority
Configure the access right for the user account
read-only
Give read-only access to the user
read-write
Give read-write access to the user
auth-type
Configure the authentication protocol for the SNMP
server user account
none
Do not use any authentication protocol
md5
Use MD5 authentication
sha
Use SHA authentication
auth-passwd
Configure the authentication password for the SNMP
server user account
authentication-password (64)
The authentication password
encryption
Configure the data encryption protocol for the SNMP
server user account
disable
Disable data encryption
des
Use DES data encryption
aes
Use AES data encryption
encryption-key
Configure the data encryption key for the SNMP
server user account
encryption-key (64)
The data encryption key
Defaults
There is no user account table by default
Command Modes
Global configuration
Usage Guidelines
If the authentication type is set to none, data encryption should be disabled.
If the authentication type is not none, an authentication password must be set up.
If data encryption is not disabled, a data encryption key must be set up.
Examples
moxa(config)# snmp-server user testNoAuthNoPriv authority read-write auth-type none
encryption disable
moxa(config)#
moxa(config)#
moxa(config)# snmp-server user testAuthNoPriv authority read-write auth-type md5
auth-passwd 1111111111 encryption disable
moxa(config)#
moxa(config)#
moxa(config)# snmp-server user testAuthPriv authority read-write auth-type md5
auth-passwd 1111111111 encryption des encryption-key 2222222222
moxa(config)#
moxa(config)#
Error Messages
% If authentication-type is none, data-encryption method should be disabled
% must setup authentication password
% must setup data encryption key
% Can't get snmp-server user-account information
% Can't get snmp-server user-account table
% Can't get snmp-server user-account table index ('%d')
% Can't get user-name from snmp-server user-account table('%d')
Moxa Command Line Interface Commands
3-122
% Can't create user account
% Can't modify user account
Related Commands
snmp-server
show snmp-server
Delete SNMP Server User Account
Commands
no snmp-server user <user-name (32)>
Syntax Description
no
Disable the configuration/delete the entry/reset to default value
snmp-server
Configure SNMP server parameters
user
Configure SNMP server user accounts
user-name (32)
The user name of the SNMP server user account
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
moxa(config)# no snmp-server user testNoAuthNoPriv
moxa(config)# no snmp-server user testAuthNoPriv
moxa(config)# no snmp-server user testAuthPriv
Error Messages
% Can't get snmp-server user-account information
% Can't get snmp-server user-account table
% Can't get snmp-server user-account table index ('%d')
% Can't get user-name from snmp-server user-account
% Can't delete user account
Related Commands
snmp-server
show snmp-server
Configure SNMP Trap Host Settings
Commands
snmp-trap host <host-address(32)> mode { trap-v1 | trap-v2c | inform-v2c | trap-v3 | inform-v3 }
[community <community-name(32)>]
Syntax Description
snmp-trap
Configure SNMP trap parameters
host
Configure the SNMP trap host address
host-address (32)
The SNMP trap host address
mode
Configure the SNMP trap mode
trap-v1
Use trap-v1 mode
trap-v2c
Use trap-v2c mode
inform-v2c
Use inform-v2c mode
trap-v3
Use trap-v3 mode
inform-v3
Use inform-v3 mode
community
Configure the community for the SNMP trap host
community-name (32)
The community name for the SNMP trap host
Defaults
There is no SNMP trap host entry by default
Command Modes
Global configuration
Usage Guidelines
A community name must be set when using trap-v1, trap-v2c, or infom-v2c mode.
SNMP v3 must be enabled when SNMP trap-v3 mode is enabled.
At least one valid user must be set up before setting the SNMP trap host to trap-v3 mode.
Examples
moxa(config)# snmp-trap host 192.168.127.254 mode trap-v1 community public
moxa(config)# snmp-trap host 192.168.127.253 mode inform-v3
Error Messages
% Can't get snmp-trap host information
% Can't get host name from snmp-trap host table
Moxa Command Line Interface Commands
3-123
% Can't get snmp-trap host table index('%d')
% Can't get host-name from snmp-trap host table('%d')
% Can't create host entry
% Can't modify host entry
% must set community name when mode is trap-v1, trap-v2c or infom-v2c
% must enable v3 in snmp-server when snmp-trap host <host-address> trap-v3 mode
is enable
% Atleast setup one valid user before enable snmp-trap host to trap-v3 mode
Related Commands
snmp-trap
show snmp-trap
Delete SNMP Trap Host Entry
Commands
no snmp-trap host <host-address(32)>
Syntax Description
no
Disable the configuration/delete the entry/reset to default value
snmp-trap
Configure SNMP trap parameters
host
Configure the SNMP trap host address
host-address (32)
The SNMP trap host address
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
moxa(config)# no snmp-trap host 192.168.127.254
moxa(config)# no snmp-trap host 192.168.127.253
Error Messages
% Can't get snmp-trap host information
% Can't get host name from snmp-trap host table
% Can't get snmp-trap host table index('%d')
% Can't get host-name from snmp-trap host table('%d')
% Can't delete host entry
Related Commands
snmp-trap
show snmp-trap
Configure SNMP Trap Inform Retry Setting
Commands
snmp-trap inform-retries <inform-retries-number(1-99)>
Syntax Description
snmp-trap
Configure SNMP trap parameters
inform-retries
Configure SNMP trap inform retries
inform-retries-number (1-99)
The amount of SNMP trap inform retries
Defaults
The default number of SNMP trap inform retries is set to 3
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
moxa(config)# snmp-trap inform-retries 3
Error Messages
N/A
Related Commands
snmp-trap
show snmp-trap
Moxa Command Line Interface Commands
3-124
Reset SNMP Trap Inform Retry to Default Value
Commands
no snmp-trap inform-retries
Syntax Description
no
Disable the configuration/delete the entry/reset to default value
snmp-trap
Configure SNMP trap parameters
inform-retries
Configure SNMP trap inform retries
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
moxa(config)# no snmp-trap inform-retries
Error Messages
N/A
Related Commands
snmp-trap
show snmp-trap
Configure SNMP Trap Inform Timeout Setting
Commands
snmp-trap inform-timeout <inform-timeout-number(1-300)>
Syntax Description
snmp-trap
Configure SNMP trap parameters
inform-timeout
Configure the SNMP trap inform timeout
inform-timeout-number (1-300)
The SNMP trap inform timeout in seconds
Defaults
The default SNMP trap inform timeout is set to 10 seconds
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
moxa(config)# snmp-trap inform-timeout 10
Error Messages
N/A
Related Commands
snmp-trap
show snmp-trap
Reset SNMP Trap Inform Timeout to Default Value
Commands
no snmp-trap inform-timeout
Syntax Description
no
Disable the configuration/delete the entry/reset to default value
snmp-trap
Configure SNMP trap parameters
inform-timeout
Configure the SNMP trap inform timeout
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
moxa(config)# no snmp-trap inform-timeout
Error Messages
N/A
Related Commands
snmp-trap
show snmp-trap
Moxa Command Line Interface Commands
3-125
Configure SNMP Trap User Account Settings
Commands
snmp-trap user <user-name(32)> auth-type { none | md5 | sha } [auth-passwd
<authentication-password(64)> ] encryption { disable| des | aes } [encryption-key <encryption-key(64)>]
Syntax Description
snmp-trap
Configures SNMP trap parameters
user
Configure SNMP trap user accounts
user-name(32)
The user name of the SNMP trap user account
auth-type
Configure the authentication protocol for the SNMP
trap user account
none
Do not use any authentication protocol
md5
Use MD5 authentication
sha
Use SHA authentication
auth-passwd
Configure the authentication password for the SNMP
trap user account
authentication-password (64)
The authentication password
encryption
Configure the data encryption protocol for the SNMP
trap user account
disable
Disable data encryption
des
Use DES data encryption
aes
Use AES data encryption
encryption-key
Configure the data encryption key for the SNMP trap
user account
encryption-key (64)
The data encryption key
Defaults
There is no user account table by default
Command Modes
Global configuration
Usage Guidelines
If the authentication type is set to none, data encryption should be disabled.
If the authentication type is not none, an authentication password must be set up.
If data encryption is not disabled, a data encryption key must be set up.
Examples
moxa# con t
moxa(config)# snmp-trap user test auth-type none encryption disable
moxa(config)# snmp-trap user test auth-type md5 auth-passwd 1111111111
encryption disable
moxa(config)# snmp-trap user test auth-type md5 auth-passwd 1111111111
encryption des encryption-key 2222222222
Error Messages
% If authentication-type is none, data-encryption method should be disabled
% must setup authentication password
% must setup data encryption key
% Can't get snmp-trap user-account information
% Can't get snmp-trap user-account table
% Can't get snmp-trap user-account table index ('%d')
% Can't get user-name from snmp-trap user-account table('%d')
% Can't create user account
% Can't modify user account
Related Commands
snmp-trap
show snmp-trap
Moxa Command Line Interface Commands
3-126
Delete SNMP Trap User Account
Commands
no snmp-trap user <user-name (32)>
Syntax Description
no
Disable the configuration/delete the entry/reset to default value
snmp-trap
Configures SNMP trap parameters
user
Configure SNMP trap user accounts
user-name (32)
The user name of the SNMP trap user account
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
moxa(config)# no snmp-trap user test
Error Messages
% Can't get snmp-trap user-account information
% Can't get snmp-trap user-account table
% Can't get snmp-trap user-account table index ('%d')
% Can't get user-name from snmp-trap user-account
% Can't delete user account
Related Commands
snmp-trap
show snmp-trap
Show SNMP Server Information
Commands
show snmp-server information
Syntax Description
show
Display the configuration/statistics/general information
snmp-server
Display SNMP server information
information
Display general SNMP server information
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
moxa# show snmp-server information
----------------------------------------------
snmp-server : enable
----------------------------------------------
version : v1-v2c
community read-only : public
community read-write : private
Error Messages
% Can't get snmp-server information
% Can't get snmp-server community information
Related Commands
snmp-server
Moxa Command Line Interface Commands
3-127
Show SNMP Server User Account Information
Commands
show snmp-server user
Syntax Description
show
Displays the configuration/statistics/general information
snmp-server
Displays SNMP server information
user
Displays SNMP server user accounts
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
moxa# show snmp-server user
----------------------------------------------
snmp-server user-account : 3
----------------------------------------------
user-name : testNoAuthNoPriv
authority : read_write
authenticate-type : none
encryption-method : disable
user-name : testAuthNoPriv
authority : read_write
authenticate-type : md5
encryption-method : disable
user-name : testAuthPriv
authority : read_write
authenticate-type : md5
encryption-method : des
Error Messages
% Can't get snmp-server user-account information
% Can't get snmp-server user-account table
Related Commands
snmp-server
Show SNMP Server Engine ID Information
Commands
show snmp-server engine-id
Syntax Description
show
Display the configuration/statistics/general information
snmp-server
Display SNMP server information
engine-id
Display the engine ID of the SNMP server
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
moxa# show snmp-server engine-id
snmp-server engineID : 800021f303000111234567
Error Messages
% Can't get snmp-server status information
% Can't get snmp-server status information jason object
Related Commands
snmp-server
Moxa Command Line Interface Commands
3-128
SNMP Trap/Inform
Show SNMP Trap Information
Commands
show snmp-trap information
Syntax Description
show
Display the configuration/statistics/general information
snmp-trap
Display SNMP trap information
information
Display general SNMP trap information
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
moxa# show snmp-trap information
----------------------------------------------
snmp-trap :
----------------------------------------------
inform-retry : 3
inform-timeout : 10
Error Messages
% Can't get snmp-trap information
% Can't get snmp-trap jason object
Related Commands
snmp-trap
Show SNMP Trap User Account Information
Commands
show snmp-trap user
Syntax Description
show
Display the configuration/statistics/general information
snmp-trap
Display SNMP trap information
user
Display SNMP trap user accounts
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
moxa# show snmp-trap user
----------------------------------------------
snmp-trap user-account : 1
----------------------------------------------
user-name : testNoAuthNoPriv
authenticate-type : none
encryption-method : disable
Error Messages
% Can't get snmp-trap user-account information
% Can't get snmp-trap user-account table
% Can't get snmp-trap user-account table index ('%d')
Related Commands
snmp-trap
Moxa Command Line Interface Commands
3-129
Show SNMP Trap Host Information
Commands
show snmp-trap host
Syntax Description
show
Display the configuration/statistics/general information
snmp-trap
Display SNMP trap information
host
Display SNMP trap host information
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
moxa# show snmp-trap host
----------------------------------------------
snmp-trap host-table : 2
----------------------------------------------
hostName : 192.168.137.254
mode : trap-v1
community : public
hostName : 192.168.127.253
mode : inform-v3
community :
Error Messages
% Can't get snmp-trap host information
% Can't get snmp-trap host table
% Can't get snmp-trap host table index('%d')
Related Commands
snmp-trap
Moxa Command Line Interface Commands
3-130
Security
Device Security
Management Interface
Enable Network Server
Commands
ip { http | https | telnet | ssh | moxa-command } server enable
Syntax Description
ip
Configure IP parameters
http
Configure HTTP management UI service parameters
https
Configure HTTPS management UI service parameters
telnet
Configure Telnet management UI service parameters
ssh
Configure SSH management UI service parameters
moxa-command
Configure Moxa Command management UI service
parameters
server
Configure management UI service server parameters
enable
Enable the management UI service
Defaults
http: enabled
https: enabled
telnet: enabled
ssh: enabled
moxa-command: enabled
Command Modes
Global Configuration
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# ip https server enable
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-131
Disable Network Server
Commands
ip { http | https | telnet | ssh | moxa-command } server disable
Syntax Description
ip
Configure IP parameters
http
Configure HTTP management UI service parameters
https
Configure HTTPS management UI service parameters
telnet
Configure Telnet management UI service parameters
ssh
Configure SSH management UI service parameters
moxa-command
Configure Moxa Command management UI service parameters
server
Configure management UI service server parameters
disable
Disable the management UI service
Defaults
http: enabled
https: enabled
telnet: enabled
ssh: enabled
moxa-command: enabled
Command Modes
Global Configuration
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# ip telnet server disable
Error Messages
N/A
Related Commands
N/A
Configure Network Port Numbers
Commands
ip { http | https | telnet | ssh } port <port-number>
Syntax Description
ip
Configure IP parameters
http
Configure HTTP management UI service parameters
https
Configure HTTPS management UI service parameters
telnet
Configure Telnet management UI service parameters
ssh
Configure SSH management UI service parameters
port
Configure the service port of the management UI service
port-number
The service port number
Defaults
http server port: 80
https server port: 443
telnet server port: 23
ssh server port: 22
Command Modes
Global Configuration
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# ip http port 8080
Error Messages
Invalid: UI service management port port-number is duplicated.
Related Commands
N/A
Moxa Command Line Interface Commands
3-132
Configure SNMP Server Port Number
Commands
snmp-server port <port-number>
Syntax Description
snmp-server
Configure SNMP server parameters
port
Configure the service port of the SNMP server
port-number
The service port number
Defaults
The default SNMP server port is set to 161
Command Modes
Global Configuration
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# snmp-server port 1661
Error Messages
N/A
Related Commands
N/A
Configure Network Maximum Session Numbers
Commands
ip http max-session <session-number>
Syntax Description
ip
Configure IP parameters
http
Configure HTTP/HTTPS management UI service parameters
max-session
Configure the maximum number of concurrent login sessions
through HTTP and HTTPS
session-number
The maximum number of login sessions
Defaults
The maximum number of concurrent HTTP sessions is set to 5 by default
Command Modes
Global Configuration
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# ip http max-session 3
Error Messages
N/A
Related Commands
N/A
Configure Network Terminal Maximum Session Numbers
Commands
ip terminal max-session <session-number>
Syntax Description
ip
Configure IP parameters
terminal
Configure Telnet and SSH terminal parameters
max-session
Configure the maximum number of concurrent login sessions
through Telnet and SSH terminal
session-number
Maximum number of login sessions
Defaults
max terminal session: 1
Command Modes
Global Configuration
Usage Guidelines
N/A
Examples
moxa# configure terminal
moxa(config)# ip terminal max-session 3
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-133
Show Network Service Information
Commands
show ip service information
Syntax Description
show
Display configuration/status information
ip
Display IP information
service
Display management UI service information
information
Display the information for management UI services
Defaults
N/A
Command Modes
User EXEC
Privileged EXEC
Usage Guidelines
N/A
Examples
moxa# show ip service information
HTTP service: Enabled
HTTP port: 80
HTTPS service: Enabled
HTTPS port: 443
Telnet service: Enabled
Telnet port: 23
SSH service: Enabled
SSH port: 22
SNMP service: Enabled
SNMP port: 161
MOXA service: Enabled
HTTP/HTTPS Maximum Login Sessions: 5
Telnet/SSH Maximum Login Sessions: 1
Error Messages
N/A
Related Commands
N/A
Login Policy
Configure Login Lockout Settings
Commands
login lockout <enable|disable>
login lockout <minute(1-10)> attempts <tries(1-10)>
Syntax Description
login
Configure login parameters
lockout
Configure the maximum number of failed login attempts and the
lockout time to block the user from logging in
enable
Enable login lockout
disable
Disable login lockout
minute
Configure the lockout time ranging from 1 to 10 minutes
attempts
Configure the maximum number of login attempts
tries
The number of tries ranging from 1 to 10
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
(config)# login lockout 10 attempts 5
(config)# login lockout enable
(config)# login lockout disable
Error messages
N/A
Related commands
N/A
Moxa Command Line Interface Commands
3-134
Configure Login Banner
Commands
login banner <string (500)>
no login banner
Syntax Description
no
Remove configuration/delete entry/reset to default value
login
Configure login parameters
banner
Configure a login banner
string
The login banner content up to 500 characters
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
(config)# login banner “this is a banner”
(config)# no login banner
Error messages
N/A
Related commands
N/A
Configure Login Failure Message
Commands
login fail-message <string (500)>
no login fail-message
Syntax Description
no
Remove configuration/delete entry/reset to default value
login
Configure login parameters
fail-message
Configure a login failure message
string
The login failure message up to 500 characters
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
(config)# login fail-message “this is a failure message”
(config)# no login fail-message
Error messages
N/A
Related commands
N/A
Configure Timeout Value for a Session End
Commands
session timeout <integer (1-1440)>
Syntax Description
session
Configure session parameters
timeout
Configure the session timeout value
integer
The timeout value ranging from 1 to 1440 seconds
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
(config)# session timeout 100
Error messages
N/A
Related commands
N/A
Moxa Command Line Interface Commands
3-135
Show Session Timeout Information
Commands
show session timeout
Syntax
Description
show
Display running information
session
Display session information
timeout
Display session timeout information
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
moxa# show session timeout
Session TimeOut: 5 (Min)
Error messages
N/A
Related commands
N/A
Show Login Failure Message
Commands
show login fail-message
Syntax Description
show
Display running information
login
Display login information
fail-message
Display the login failure message
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
moxa# show log fail-message
Login Fail Message:
This is a failed message!
Error messages
N/A
Related commands
N/A
Show Login Banner
Commands
show login banner
Syntax Description
show
Display running information
login
Display login information
banner
Display the login banner
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
moxa# show log banner
Login Banner Message:
this is a banner
Error messages
N/A
Related commands
N/A
Moxa Command Line Interface Commands
3-136
Show Login Authentication
Commands
show login authentication
Syntax Description
show
Display running information
login
Display login information
authentication
Display authentication information
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
moxa# show login authentication
Login Authentication Method: Local
Error messages
N/A
Related commands
N/A
Trusted Access
Configure Trusted Access Settings
Commands
trusted-access ip-source <ucast_addr> [ { <ip_mask> | "/" <short(0-32)> } ]
no trusted-access <ucast_addr> [ { <ip_mask> | "/" <short(0-32)> } ]
Syntax Description
no
Disable the configuration/delete the entry/reset to default value
trusted-access
Configure IP trusted access parameters
ip-source
Configure the IP source
ucast_addr
Configure the network or host IP address
ip_mask
Configure the subnet mask of the IP address
"/"
Configure the CIDR notation
short (0-32)
Configure the prefix length
Defaults
Trusted access is disabled by default
Command Modes
Privileged EXEC
Global Configuration
Usage Guidelines
Trusted access will take effect when the “trusted-access enable” command is executed.
Examples
(config)# trusted-access ip-source 10.10.10.10 255.255.255.0
(config)# trusted-access ip-source 20.10.10.10 / 24
(config)# trusted-access ip-source 30.10.10.10
(config)# no trusted-access ip-source 10.10.10.10 255.255.255.0
(config)# no trusted-access ip-source 20.10.10.10 / 24
(config)# no trusted-access ip-source 30.10.10.10
Error Messages
N/A
Related Commands
show trusted-access
trusted-access enable
Moxa Command Line Interface Commands
3-137
Enable/Disable IP Trusted Access List
Commands
trusted-access <enable>
trusted-access <disable>
Syntax Description
trusted-access
Configure IP trusted access parameters
enable
Enable the IP trusted access list
disable
Disable the IP trusted access list
Defaults
N/A
Command Modes
Privileged EXEC
Global Configuration
Usage Guidelines
N/A
Examples
(config)# trusted-access enable
(config)# trusted-access disable
Error messages
N/A
Related commands
trusted-access disable
Show Trusted Access IP List
Commands
show trusted-access
Syntax Description
show
Display configuration/status information
trusted-access
Display IP trusted access information
Defaults
N/A
Command Modes
User EXEC
Privileged EXEC
Usage Guidelines
N/A
Examples
moxa# show trusted-access
Trusted Access Table : Disabled
---------------------------
IP Address : 210.222.222.225
Subnet Mask : 255.255.255.0
moxa#
Error Messages
% No such manager found
% Manager is not configured
Related Commands
trusted-access
Moxa Command Line Interface Commands
3-138
SSH & SSL
Re-generate New Web SSL Certificate
Commands
web certificate generate
Syntax Description
web
Configure web parameters
certificate
Configure the web server certificate
generate
Generate a self-signed certificate
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
(config)# web certificate generate
Error messages
N/A
Related commands
N/A
Import New Web SSL Certificate via TFTP or SFTP
Commands
web certificate import {<tftp_url> | <sftp_url>}
Syntax Description
web
Configure web parameters
certificate
Configure the web server certificate
import
Import the certificate from a remote server
tftp_url
The file on the remote TFTP server to be copied
sftp_url
The file on the remote SFTP server to be copied
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
(config)# web certificate import tftp://192.168.1.1/server.crt
Error messages
Format or Password Error
Server not Connected
Related commands
N/A
Export Web SSL Certificate Signing Request via TFTP/SFTP
Commands
web signing-request export {<tftp_url> | <sftp_url>}
Syntax Description
web
Configure Web related parameters
signing-request
Configure the web server certificate signing request
export
Export the certificate
tftp_url
The file on the remote TFTP server to be copied
sftp_url
The file on the remote SFTP server to be copied
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
(config)# web signing-request export tftp://192.168.1.1/server.csr
Error Messages
Server not Connected
Related Commands
N/A
Moxa Command Line Interface Commands
3-139
Re-generate New SSH Key
Commands
ssh key generate
Syntax Description
ssh
Configure SSH parameters
key
Configure the SSH server key
generate
Generate the SSH key
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
(config)# ssh key generate
Error messages
N/A
Related commands
N/A
Network Security
IEEE802.1X
Configure Local Authentication Mode
Commands
dot1x aaa auth { radius | local }
Syntax Description
dot1x
Configure IEEE 802.1X port-based network access control
aaa
Configure authentication, authorization, and accounting
auth
Configure authentication
radius
Configure a RADIUS authentication server
local
Configure a local authentication database
Defaults
The default authentication mode is set to local
Command Modes
Global configuration mode
Usage Guidelines
This command enables dot1x local authentication or RADIUS server-based remote
authentication method for all ports. The actual authentication of the supplicant happens
at the authentication server.
Examples
moxa(config)# dot1x aaa auth radius
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-140
Enable/Disable IEEE802.1X Function
Commands
dot1x { enable | disable }
Syntax Description
dot1x
Configure IEEE 802.1X port-based network access control
enable
Enable dot1x authentication
disable
Disable dot1x authentication
Defaults
Dot1x authentication is disabled by default
Command Modes
Global configuration mode
Usage Guidelines
This command enables dot1x on the switch. Dot1x is an authentication mechanism that
acts as mediator between the authentication server and the supplicant (client). If the
client accesses the protected resources, it contacts the authenticator with EAPOL frames.
Examples
moxa (config)# dot1x enable
Error Messages
{{!s}} and 802.1x/MAB cannot be enabled at the same port.
Invalid: If 802.1x port is enabled, the port security port cannot be enabled.
Invalid: If the port is in port-channel, it cannot enable dot1x.
Related Commands
N/A
Configure IEEE802.1X on the Port
Commands
dot1x
no dot1x
Syntax Description
dot1x
Enable dot1x on the port.
no dot1x
Disable dot1x on the port.
Defaults
Dot1x is disabled by default
Command Modes
Interface Configuration Mode
Usage Guidelines
This command enables dot1x on the specified port.
Examples
moxa (config-if)# dot1x
moxa (config-if-range)# dot1x
Error Messages
{{!s}} and 802.1x/MAB cannot be enabled at the same port.
Invalid: If 802.1x port is enabled, the port security port cannot be enabled.
Invalid: If the port is in port-channel, it cannot enable dot1x.
Related Commands
N/A
Moxa Command Line Interface Commands
3-141
Authorize IEEE802.1X
Commands
dot1x port-control { auto | force-authorized | force-unauthorized }
no dot1x port-control
Syntax Description
dotx1
Configure IEEE 802.1X port-based network access control
port-control
Configure authenticator port control parameters
auto
Enable 802.1X authentication on the interface
force-authorized
Allow all traffic without any restrictions
force-unauthorized
Block all traffic over the interface
no
Set the authenticator port control state to force-authorized.
Defaults
The default port-control mode is set to force-authorized
Command Modes
Interface Configuration Mode
Usage Guidelines
This command configures the authenticator port control parameter. The dot1x standard
exercises port-based authentication to increase the security of the network. The different
modes employed on the ports offer varied access levels.
Examples
moxa (config-if)# dot1x port-control auto
moxa (config-if-range)# dot1x port-control auto
Error Messages
N/A
Related Commands
N/A
Configure Maximum Number of EAP
Commands
dot1x max-req < count (1-10) >
no dot1x max-req
Syntax Description
no
Remove configuration/delete entry/reset to default value
dot1x max-req
Configure the dot1X maximum request count
count
The count value ranging from 1 to 10.
no
Set the maximum number of EAP retries to the client to the default
value
Defaults
The default request count is set to 2
Command Modes
Interface Configuration Mode
Usage Guidelines
This command sets the maximum number of EAP (Extensible Authentication Protocol)
retries to the client by the authenticator before restarting the authentication process.
Examples
moxa (config-if)# dot1x max-req 2
moxa (config-if-range)# dot1x max-req 2
Error Messages
Invalid input detected at '^' marker
Related Commands
N/A
Moxa Command Line Interface Commands
3-142
Configure IEEE802.1X Reauthentication
Commands
dot1x reauthentication
no dot1x reauthentication
Syntax Description
no
Remove configuration/delete entry/reset to default value
dot1x
Configure IEEE 802.1X port-based network access control
reauthentication
Perform periodic reauthentication
Defaults
Dot1x reauthentication is disabled by default
Command Modes
Interface Configuration Mode.
Usage Guidelines
This command enables periodic re-authentication from authenticator to client. The
periodic re-authentication is requested to ensure that the same supplicant is accessing
the protected resources.
Examples
moxa (config-if)# dot1x reauthentication
moxa (config-if-range)# dot1x reauthentication
Error Messages
Invalid: If port Control mode is not Auto, Reauthentication cannot be enabled.
Related Commands
dot1x timeout – Sets the dot1x timers
dot1x port-control – Configures the authenticator port control parameter
Reauthenticate IEEE802.1X on the Port
Commands
dot1x re-authenticate
Syntax Description
dotx1
Configure IEEE 802.1X port-based network access control
re-authenticate
Perform re-authentication of the specified dot1x-enabled port
Defaults
N/A
Command Modes
Privileged EXEC Mode
Usage Guidelines
Re-authentication is requested by the authentication server to the supplicant to furnish
the identity without waiting for the configured number of seconds. (re-authperiod).
Examples
moxa (config-if) # dot1x re-authenticate
moxa (config-if-range) # dot1x re-authenticate
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-143
Configure IEEE802.1X Settings
Commands
dot1x timeout { quiet-period < value (0-65535) > | { reauth-period | server-timeout | supp-timeout |
tx-period } < value (1-65535) > }
no dot1x timeout { quiet-period | reauth-period | server-timeout | supp-timeout | tx-period }
Syntax Description
dot1x
Configure IEEE 802.1X port-based network access control
timeout
Configure the dot1x timeout parameter
quiet-period
The number of seconds that the switch remains in the quiet state
following a failed authentication exchange with the client
reauth-period
The number of seconds between re-authentication attempts
server-timeout
The number of seconds that the switch waits for the retransmission
of packets by the switch to the authentication server
supp-timeout
The number of seconds that the switch waits for the retransmission
of packets by the switch to the client
tx-period
The number of seconds that the switch waits for a response to an
EAP-request/identity frame from the client before retransmitting
the request
no
Set the dot1x timers to their default values
Defaults
quiet-period: 60 seconds
reauth-period: 3600 seconds
server-timeout: 30 seconds
supp-timeout: 30 seconds
tx-period: 30 seconds
Command Modes
Interface configuration mode
Usage Guidelines
This command sets the dot1x timers.
Examples
moxa (config-if)# dot1x timeout quiet-period 30
moxa (config-if-range)# dot1x timeout quiet-period 30
Error Messages
Invalid input detected at '^' marker
Related Commands
dot1x max-req – Sets the maximum number of EAP retries to the client before restarting
authentication process.
dot1x reauthentication – Enables periodic re-authentication of the client.
Moxa Command Line Interface Commands
3-144
Show IEEE802.1X Information
Commands
show dot1x [ { interface < interface-type > < interface-id > | local-database | all } ]
Syntax Description
show
Display configuration/statistics/general information
dot1x
Configure IEEE 802.1X port-based network access control
interface-type
The interface type
interface-id
The slot number/port number
local-database
Display the dot1x authentication server database with user names
all
Display the dot1x status for all interfaces
Defaults
N/A
Command Modes
Privileged EXEC Mode
Usage Guidelines
This command displays dot1x information.
Examples
moxa # show dot1x
iss# show dot1x
Sysauthcontrol = Enabled
Dot1x Authentication Method = Local
moxa # show dot1x interface gigabitethernet 1/2
Dot1x Info for Eth1/2
---------------------
AuthPaeStatus = ENABLED
PortStatus = UNAUTHORIZED
MaxReq = 2
Port Control = Auto
QuietPeriod = 60 Seconds
Re-authentication = Disabled
ReAuthPeriod = 3600 Seconds
ServerTimeout = 30 Seconds
SuppTimeout = 30 Seconds
Tx Period = 30 Seconds
moxa # show dot1x local-database
Pnac Authentication Users Database
-----------------------------------
User name : user1
Ports : Eth1/1, Eth1/2, Eth1/3, Eth1/4, Eth2/1, Eth2/2
Eth2/3, Eth2/4, Eth3/1, Eth3/2, Eth3/3, Eth3/4
Eth4/1, Eth4/2, Eth4/3, Eth4/4, Eth5/1, Eth5/2
Eth5/3, Eth5/4, Eth6/1, Eth6/2, Eth6/3, Eth6/4
Eth7/1, Eth7/2, Eth7/3, Eth7/4
---------------------------------
User name : user2
Ports : Eth1/1, Eth1/2, Eth1/3, Eth1/4, Eth2/1, Eth2/2
Eth2/3, Eth2/4, Eth3/1, Eth3/2, Eth3/3, Eth3/4
Eth4/1, Eth4/2, Eth4/3, Eth4/4, Eth5/1, Eth5/2
Eth5/3, Eth5/4, Eth6/1, Eth6/2, Eth6/3, Eth6/4
Eth7/1, Eth7/2, Eth7/3, Eth7/4
---------------------------------
Error Messages
N/A
Related Commands
dot1x local-database - Configures dot1x local database with values
dot1x system-auth-control – Enables dot1x in the switch
dot1x max-req - Configures the maximum number of EAP retries to the client
dot1x reauthentication - Configures the periodic reauthentication for the client
dot1x timeout – Sets the dot1x timers
Moxa Command Line Interface Commands
3-145
Configure IEEE802.1X Server Host
Commands
dot1x auth radius-server host { ipv4-address } [ auth-port < integer(1-65535) > ] [ timeout <1-120> ]
[ retransmit <1-254> ] [ key < secret-key-string > ] [ primary ]
no dot1x auth radius-server host { < ipv4-address > } [ primary ]
Syntax Description
dot1
Configure IEEE 802.1X port-based network access control
auth radius-server host
Configure the RADIUS server host
ipv4-address
Configure the IPv4 address.
auth-port
Configure a specific UDP destination port on this RADIUS
server to be used exclusively for authentication requests.
timeout
Configure the time period in seconds for which a client
waits for a response from the server before
re-transmitting the request.
retransmit
Configure the maximum number of attempts to be tried by
a client to get a response from the server for a request.
key
Configure the per-server encryption key.
primary
Set the RADIUS server as the primary server.
no
Delete the RADIUS server configuration
Defaults
N/A
Command Modes
Global configuration mode
Usage Guidelines
This command configures the RADIUS client with the host, timeout, key, retransmit
parameters.
Examples
moxa (config)# dot1x auth radius-server host 6.7.8.9 auth-port 1812 timeout 3
retransmit 1 key 123456 primary
Error Messages
Invalid: All of the retry times {{!s}} cannot exceeds Dot1x server timeout values
{{!s}}. Note: All of the retry times = Timeout * (Retransmit + 1).
Invalid: Primary IP Address should be the same as the Server IP Address.
Invalid: Server IP Address cannot be a reserved IP Address.
Related Commands
N/A
Configure IEEE802.1X Username and Password
Commands
dot1x local-database < username > password < password >
no dot1x local-database < username >
Syntax Description
dot1x
Configure IEEE 802.1X port-based network access control
local-database
Configure the local database table
username
Configure the username for the new entry
password
Configure the password for the new entry
no
Delete the entry from the dot1x authentication server database
Defaults
N/A
Command Modes
Global configuration mode
Usage Guidelines
This command configures dot1x authentication server local database username and
password entries.
Examples
moxa (config)# dot1x local-database user password 123456
Error Messages
Invalid: This 'Username' is already in the 'Local Database'.
Related Commands
N/A
Moxa Command Line Interface Commands
3-146
Show IEEE802.1X Authentication RADIUS Server
Commands
show dot1x auth radius server
Syntax Description
show
Display configuration/statistics/general information
dot1x
Display dot1x configuration information
auth
Display authentication type information.
radius
Display RADIUS server information.
server
Display server information.
Defaults
N/A
Command Modes
Privileged EXEC Mode
Usage Guidelines
This command displays radius server information.
Examples
moxa# show dot1x auth radius server
Primary Server : 6.7.8.9
Radius Server Host Information
------------------------------
Index : 1
Server address : 6.7.8.9
Shared secret :
Radius Server Status : Enabled
Response Time : 5
Maximum Retransmission : 1
Authentication Port : 1812
--------------------------------------------
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-147
Port Security
Configure Port Security Mode
Commands
port-security mode { static-port-lock | mac-sticky }
Syntax Description
port-security
Configure port security parameters
mode
Configure the security mode (port security port/address table will
be reset when the mode changes)
static-port-lock
Use Static Port Lock mode
mac-sticky
Use MAC Sticky mode
Defaults
The default port security mode is set to static-port-lock
Command Modes
Privileged EXEC
Global Configuration
Usage Guidelines
Changing modes resets all port configurations.
Examples
moxa(config)# port-security mode mac-sticky
moxa(config)# port-security mode static-port-lock
Error Messages
"error:If 'portLimit' is changed, 'mode' must be Mac Sticky"
"error:If 'portSecurityAction' is changed," + " 'mode' must be Mac sticky"
'Invalid: Address Table cannot have duplicated addresses (VLAN ID, MAC Address).'
'Invalid: The mac address has exceeded the setting port limit.'
'Sum of port limit value on all ports ' + 'MUST under ' + str(_MAX_SUN_OF_PORT_LIMIT)
+ ' in Mac-Sticky mode'
'Invalid: Port Security MAC only support unicast address.'
'Invalid: Port Security address table VLAN ID must exist in the VLAN configuration.'
'Invalid: Port Security address table port should be added in the VLAN member.'
'Invalid: Port Security address table conflicts with VLAN configuration.'
'Invalid: If this port enables Port Security, this port cannot be a member port of Static
Unicast Port Table.'
'Invalid: If this port enables Port Security, this port cannot be a member port of
port-channel.'
'Invalid: If Port Security is enabled on this port, it cannot be a destination port of port
mirror.'
'Invalid: If Port Security action is changed, this port could not in violation state.'
'Invalid: Port Security and redundant protocol cannot be enabled on the same port.'
Related Commands
N/A
Moxa Command Line Interface Commands
3-148
Enable/Disable Port Security
Commands
port-security { enable | disable }
Syntax Description
port-security
Configure port security parameters
enable
Enable port security
disable
Disable port security
Defaults
Port security is enabled by default
Command Modes
Privileged EXEC
Global Configuration
Usage Guidelines
N/A
Examples
moxa(config)# port-security enable
moxa(config)# port-security disable
Error Messages
"error:If 'portLimit' is changed, 'mode' must be Mac Sticky"
"error:If 'portSecurityAction' is changed," + " 'mode' must be Mac sticky"
'Invalid: Address Table cannot have duplicated addresses (VLAN ID, MAC Address).'
'Invalid: The mac address has exceeded the setting port limit.'
'Sum of port limit value on all ports ' + 'MUST under ' + str(_MAX_SUN_OF_PORT_LIMIT)
+ ' in Mac-Sticky mode'
'Invalid: Port Security MAC only support unicast address.'
'Invalid: Port Security address table VLAN ID must exist in the VLAN configuration.'
'Invalid: Port Security address table port should be added in the VLAN member.'
'Invalid: Port Security address table conflicts with VLAN configuration.'
'Invalid: If this port enables Port Security, this port cannot be a member port of Static
Unicast Port Table.'
'Invalid: If this port enables Port Security, this port cannot be a member port of
port-channel.'
'Invalid: If Port Security is enabled on this port, it cannot be a destination port of port
mirror.'
'Invalid: If Port Security action is changed, this port could not in violation state.'
'Invalid: Port Security and redundant protocol cannot be enabled on the same port.'
Related Commands
N/A
Moxa Command Line Interface Commands
3-149
Configure Port Security Setting
Commands
port-security [ { limit <integer(1-1024)> | violation { packet-drop | port-shutdown } | mac-address
<ucast_mac> vlan <vlan_vfi_id> } ]
Syntax Description
port-security
Configure port security parameters
limit
The maximum number of addresses on the port
integer (1-1024)
The limit value (MAC address will be removed on the configured
port when the limit value changes)
violation
Configure the violation action on the port
packet-drop
Drop the packet when a violation occurs
port-shutdown
Shut down the port when a violation occurs
mac-address
The new MAC address
ucast_mac
The unicast MAC address
vlan
The new VLAN ID
vlan_vfi_id
The VLAN ID ranging from 1 to 4094
Defaults
no port-security: disable on ports
limit: 1
violation: secure action is packet-drop
Command Modes
Privileged EXEC
Interface Configuration
Usage Guidelines
If the limit value changes on a port, all entries on the port are deleted.
Examples
moxa(config-if)# port-security
moxa(config-if)# port-security limit 10
moxa(config-if)# port-security violation port-shutdown
moxa(config-if)# port-security mac-address 02:03:04:01:01:01 vlan 1
Error Messages
"error:If 'portLimit' is changed, 'mode' must be Mac Sticky"
"error:If 'portSecurityAction' is changed," + " 'mode' must be Mac sticky"
'Invalid: Address Table cannot have duplicated addresses (VLAN ID, MAC Address).'
'Invalid: The mac address has exceeded the setting port limit.'
'Sum of port limit value on all ports ' + 'MUST under ' + str(_MAX_SUN_OF_PORT_LIMIT)
+ ' in Mac-Sticky mode'
'Invalid: Port Security MAC only support unicast address.'
'Invalid: Port Security address table VLAN ID must exist in the VLAN configuration.'
'Invalid: Port Security address table port should be added in the VLAN member.'
'Invalid: Port Security address table conflicts with VLAN configuration.'
'Invalid: If this port enables Port Security, this port cannot be a member port of Static
Unicast Port Table.'
'Invalid: If this port enables Port Security, this port cannot be a member port of
port-channel.'
'Invalid: If Port Security is enabled on this port, it cannot be a destination port of port
mirror.'
'Invalid: If Port Security action is changed, this port could not in violation state.'
'Invalid: Port Security and {} '.format(red_protocol_def[red_protocol]) + 'cannot be
enabled on the same port.'
Related Commands
N/A
Moxa Command Line Interface Commands
3-150
Remove Port Security Setting
Commands
no port-security [ { limit | mac-address { <mac_addr> vlan <integer(1-4094)> | all } } ]
Syntax Description
no
Remove configuration/delete entry/reset to default value
port-security
Configure port security parameters
limit
The maximum number of addresses on the port
mac-address
The new MAC address
mac_addr
The MAC address
vlan
The new VLAN ID
integer (1-4094)
The VLAN ID ranging from 1 to 4094
all
All entries in the address table
Defaults
N/A
Command Modes
Privileged EXEC
Interface Configuration
Usage Guidelines
If the limit value changes on a port, all entries on the port are deleted.
Examples
moxa(config-if)# no port-security
moxa(config-if)# no port-security limit
moxa(config-if)# no port-security mac-address 02:03:04:01:01:01 vlan 1
Error Messages
"error:If 'portLimit' is changed, 'mode' must be Mac Sticky"
"error:If 'portSecurityAction' is changed," + " 'mode' must be Mac sticky"
'Invalid: Address Table cannot have duplicated addresses (VLAN ID, MAC Address).'
'Invalid: The mac address has exceeded the setting port limit.'
'Sum of port limit value on all ports ' + 'MUST under ' + str(_MAX_SUN_OF_PORT_LIMIT)
+ ' in Mac-Sticky mode'
'Invalid: Port Security MAC only support unicast address.'
'Invalid: Port Security address table VLAN ID must exist in the VLAN configuration.'
'Invalid: Port Security address table port should be added in the VLAN member.'
'Invalid: Port Security address table conflicts with VLAN configuration.'
'Invalid: If this port enables Port Security, this port cannot be a member port of Static
Unicast Port Table.'
'Invalid: If this port enables Port Security, this port cannot be a member port of
port-channel.'
'Invalid: If Port Security is enabled on this port, it cannot be a destination port of port
mirror.'
'Invalid: If Port Security action is changed, this port could not in violation state.'
'Invalid: Port Security and redundant protocol cannot be enabled on the same port.'
Related Commands
set port-security mode [static-port-lock | mac-sticky]
Show Port Security Setting
Commands
show port-security [ address ]
Syntax Description
show
Display configuration/statistics/general information
port-security
Display port security information
address
Display port security address information
Defaults
N/A
Command Modes
User EXEC
Privileged EXEC
Usage Guidelines
N/A
Examples
moxa# show port-security
moxa# show port-security address
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-151
Traffic Storm Control
Enable/Disable Storm Control
Commands
storm-control { bc | mc | dlf | bc_mc | bc_dlf | mc_dlf | bc_mc_dlf } level <rate-value(1-1488100)>
no storm-control {bc | mc | dlf | bc_mc | bc_dlf | mc_dlf | bc_mc_dlf}
Syntax Description
no
Remove configuration delete entry/reset to default value
storm-control
Configure storm control parameters
bc
Configure broadcast packet storm control parameters
mc
Configure multicast packet storm control parameters
dlf
Configure unicast packet storm control parameters
bc_mc
Configure broadcast and multicast packet storm control
parameters
bc_dlf
Configure broadcast and unicast packet storm control parameters
mc_dlf
Configure multicast and unicast packet storm control parameters
bc_mc_dlf
Configure broadcast multicast and unicast packet storm control
parameters
level
Configure the control suppression level
rate-value
(625-1488100)
The storm control rate value
Defaults
N/A
Command Modes
Privileged EXEC
Global Configuration
Usage Guidelines
N/A
Examples
moxa# configure
moxa(config)# interface ethernet 1/1
moxa(config-if)# storm-control bc level 635
moxa# configure
moxa(config)# interface ethernet 1/1
moxa(config-if)# storm-control bc_mc level 1270
moxa# configure
moxa(config)# interface ethernet 1/1
moxa(config-if)# storm-control bc_mc_dlf level 1905
moxa# configure
moxa(config)# interface ethernet 1/1
moxa(config-if)# no storm-control bc
Error Messages
'Invalid: The value of traffic storm control should be less than ingress rate limit
threshold.'
'Invalid: Your configure value {}'.format(cfg_val) + ' exists too large bias because of
limitation of hardware.' + ' We suggest configure the value {}
again.'.format(suggest_cfg_val)
Related Commands
moxa(config-if)# no storm-control {bc | mc | dlf | bc_mc | bc_dlf | mc_dlf | bc_mc_dlf}
moxa# show [<ifXtype> <ifnum>] storm-control
Moxa Command Line Interface Commands
3-152
Show Storm Control Status
Commands
show interfaces [<ifXtype> <ifnum>] storm-control
Syntax Description
show
Display configuration/status information
interface
Display interface information
ifXtype
The interface type
ifnum
The interface number
storm-control
Display the broadcast, multicast, and unicast storm control
suppression levels of the interface
Defaults
N/A
Command Modes
Privileged EXEC
Global Configuration
Usage Guidelines
N/A
Examples
moxa# show interface ethernet 1/1 storm-control
Eth1/1
DLF Storm Control : Disabled
Broadcast Storm Control : Disabled
Multicast Storm Control : Disabled
moxa# show interface ethernet 1/1 storm-control
Eth1/1
DLF Storm Control : Disabled
Broadcast Storm Control : Enabled
Broadcast Storm Control Level : 635
Multicast Storm Control : Disabled
Error Messages
N/A
Related Commands
moxa (config-if)# storm-control {bc | mc | dlf | bc_mc | bc_dlf | mc_dlf | bc_mc_dlf}
level <rate-value(625-1488100)>
moxa (config-if)# no storm-control {bc | mc | dlf | bc_mc | bc_dlf | mc_dlf | bc_mc_dlf}
Moxa Command Line Interface Commands
3-153
Authentication
Login Authentication
Configure Login Authentication Settings
Commands
login authentication [{ radius | tacacs }] [local]
Syntax Description
login
Configure login parameters
authentication
Configure authentication parameters
radius
Configure RADIUS authentication servers
tacacs
Configure a TACACS authentication system
local
Configure a local authentication database
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
(config)# login authentication radius
(config)# login authentication tacacs
(config)# login authentication local
(config)# login authentication radius local
(config)# login authentication tacacs local
Error messages
N/A
Related commands
N/A
RADIUS
Configure RADIUS Server Host Settings
Commands
radius-server host { <ucast_addr> } [auth-port {<integer(1-65535)>}] [timeout {<short(5-180)>}]
[retransmit {<short(0-5)>}] key {<string(60)>} authtype { pap | chap | mschap } { primary | secondary }
no radius-server { primary | secondary }
Syntax Description
no
Disable the configuration/delete the entry/reset to default value
radius-server
Configure RADIUS server parameters
host
Configure the RADIUS host
auth-port
Configures the UDP destination port for authentication requests
timeout
Configure time period (in seconds) until which a client waits for a
response from the server before re-transmitting the request
retransmit
Configure the maximum number of attempts the client undertakes
to contact the server
key
Configure the RADIUS server encryption key
authtype
Configure the authentication type of the RADIUS server
primary
Set as the primary server
secondary
Set as the secondary server
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
(config)# radius-server host 1.1.1.1 auth-port 2222 timeout 5 retransmit 5 key test
authtype pap primary
(config)# no radius-server primary
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-154
Show RADIUS Server Information
Commands
show radius-server
Syntax Description
show
Display running information
radius- server
Display the RADIUS server parameters
Defaults
N/A
Command Modes
Privileged EXEC / User EXEC
Usage Guidelines
N/A
Examples
moxa# show radius-server
Error messages
N/A
Related commands
N/A
TACACS+
Configure TACACS+ Server Host Settings
Commands
tacacs-server host { <ucast_addr> } [auth-port {<integer(1-65535)>}] [timeout {<short(5-180)>} ]
[retransmit {<short(0-5)>}] key {<string(60)>} authtype { pap | chap | mschap } { primary | secondary }
no tacacs-server { primary | secondary }
Syntax Description
no
Disable the configuration/delete the entry/reset to default value
tacacs -server
Configure TACACS server parameters
host
Configure TACACS host parameters
auth-port
Configure authentication port parameters
timeout
Configure timeout parameters
retransmit
Configure the maximum number of attempts the client undertakes
to contact the server
key
Configure the per-server encryption key
authtype
Configure the authentication type of the TACACS server
primary
Set as the primary server
secondary
Set as the secondary server
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
(config)# tacacs-server host 1.1.1.1 auth-port 2222 timeout 5 retransmit 5 key test
authtype pap primary
(config)# no tacacs-server primary
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-155
Show TACACS+ Server Information
Commands
show tacacs server
Syntax Description
show
Displays running information
tacacs-server
Displays the TACACS server parameters
Defaults
N/A
Command Modes
Privileged EXEC / User EXEC
Usage Guidelines
N/A
Examples
moxa# show tacacs-server
Error messages
N/A
Related commands
N/A
Diagnostics
System Status
Utilization
Show Device Current Information
Commands
show env {all | power | RAM | CPU }
Syntax Description
show
Display the statistics information
env
Display switch information
all
Show the current information for all resources such as CPU, RAM,
and power
power
Show the current power input information
RAM
Show the current RAM information
CPU
Show the current CPU information
Defaults
N/A
Command Modes
Global configuration / User EXEC
Usage Guidelines
N/A
Examples
# show env all
# show env power
# show env RAM
# show env CPU
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-156
Statistics
Show Traffic Statistics
Commands
show statistics [ interface <interface-type> <interface-id> ]
Syntax Description
show
Display configuration/status information
statistics
Display the interface statistics table
interface-type
Display interface information
interface-id
Display the specific interface information
Defaults
N/A
Command Modes
Privileged EXEC Mode.
Usage Guidelines
N/A
Examples
moxa# show statistics interface ethernet 1/1
Error Messages
N/A
Related Commands
clear statistics
Clear Traffic Statistics
Commands
clear statistics [ interface < interface-type> <interface-id> ]
Syntax Description
clear
Clear input
statistics
Clear statistics
interface-type
The interface type
interface-id
The interface ID
Defaults
N/A
Command Modes
Privileged EXEC Mode.
Usage Guidelines
N/A
Examples
moxa# clear statistics Ethernet 1/1
Error messages
N/A
Related commands
show statistics
Moxa Command Line Interface Commands
3-157
Module Information
Show Module information
Commands
show product information
Syntax Description
show
Display configuration/status information
product
Display product information
information
Display product information
Defaults
N/A
Command Modes
User EXEC
Privileged EXEC
Usage Guidelines
N/A
Examples
moxa# show product information
Product Information
Model : MDS-G4028
Serial Number : 123456789ABC
MAC : 00:01:03:05:07:09
Firmware Version : v0.3 Build 2019_0502_2111
Hardware Version : V0.0.0
Module Information
Type Module Name Serial Number Hardware Version
Module [1] MDS-G4028 123456789ABC V0.0.0
Module [2] -- -- --
Module [3] -- -- --
Module [4] -- -- --
Module [5] -- -- --
Module [6] -- -- --
Module [7] -- -- --
Power Unit [1] -- -- --
Power Unit [2] -- -- --
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-158
Event Notification
Event Notification
Show Event Notification
Commands
show event-notification {general-event | poe-event | port-event | switching-event}
Syntax Description
show
Displays running information for the feature
event-notification
Display event-notification configuration
general-event
general event config
poe-event
poe event config
port-event
port event config
switching-event
switching event config
Defaults
N/A
Command Modes
Privileged EXEC /User EXEC
Usage Guidelines
N/A
Examples
moxa# show event-notification poe-event
PD Power On
Event Enable :Enabled
Registered Action :Trap, Email,
PD Power Off
Event Enable :Enabled
Registered Action :Trap, Email,
Low Input Voltage
Event Enable :Enabled
Registered Action :Trap, Email,
PD Over Current
Event Enable :Enabled
Registered Action :Trap, Email,
PD No Response
Event Enable :Enabled
Registered Action :Trap, Email,
Over Power Budget Limit
Event Enable :Enabled
Registered Action :Trap, Email,
Power Detection Failure
Event Enable :Enabled
Registered Action :Trap, Email,
moxa# show event-notification port-event
Port link up
Event Enable :Enabled
Registered Action :Trap, Email,
Registered Port :1/1, 1/2, 1/3, 1/4, 2/1, 2/2, 2/3, 2/4, 3/1, 3/2, 3/3, 3/4
, 4/1, 4/2, 4/3, 4/4, 5/1, 5/2, 5/3, 5/4, 6/1, 6/2, 6/3, 6/4, 7/1, 7/2, 7/3, 7/4
,
Port link down
Event Enable :Enabled
Registered Action :Trap, Email,
Registered Port :1/1, 1/2, 1/3, 1/4, 2/1, 2/2, 2/3, 2/4, 3/1, 3/2, 3/3, 3/4
Moxa Command Line Interface Commands
3-159
, 4/1, 4/2, 4/3, 4/4, 5/1, 5/2, 5/3, 5/4, 6/1, 6/2, 6/3, 6/4, 7/1, 7/2, 7/3, 7/4
,
Port shutdown by Rate Limit
Event Enable :Enabled
Registered Action :Trap, Email,
Registered Port :1/1, 1/2, 1/3, 1/4, 2/1, 2/2, 2/3, 2/4, 3/1, 3/2, 3/3, 3/4
, 4/1, 4/2, 4/3, 4/4, 5/1, 5/2, 5/3, 5/4, 6/1, 6/2, 6/3, 6/4, 7/1, 7/2, 7/3, 7/4
,
Port recovery by Rate Limit
Event Enable :Enabled
Registered Action :Trap, Email,
Registered Port :1/1, 1/2, 1/3, 1/4, 2/1, 2/2, 2/3, 2/4, 3/1, 3/2, 3/3, 3/4
, 4/1, 4/2, 4/3, 4/4, 5/1, 5/2, 5/3, 5/4, 6/1, 6/2, 6/3, 6/4, 7/1, 7/2, 7/3, 7/4
,
Port shutdown by Port Security
Event Enable :Enabled
Registered Action :Trap, Email,
Registered Port :1/1, 1/2, 1/3, 1/4, 2/1, 2/2, 2/3, 2/4, 3/1, 3/2, 3/3, 3/4
, 4/1, 4/2, 4/3, 4/4, 5/1, 5/2, 5/3, 5/4, 6/1, 6/2, 6/3, 6/4, 7/1, 7/2, 7/3, 7/4
Error Messages
N/A
Related Commands
event-notification general-event
event-notification poe-event
event-notification port-event
event-notification switching-event
Moxa Command Line Interface Commands
3-160
Configure Event Notification Settings
Commands
event-notification general-event all
event-notification general-event cold-start
event-notification general-event all action trap mgmt-relay
event-notification general-event cold-start action email pwr1-relay
no event-notification general-event all
no event-notification general-event cold-start action email pwr2-relay
Syntax Description
no
Disable the configuration/deletes the entry/reset to
default value
event-notification
Configure event notifications
general-event
Configure notifications for general events
all
Notify for all general events
cold-start
Notify when the system performs a cold start
warm-start
Notify when the system performs a warm start
config-change
Notify when the system configuration changes
login-success
Notify when a user successfully logs in
login-fail
Notify when a user failed to log in
login-lockout
Notify when a user is locked out due to the login policy
account-setting-changed
Notify when the user account information changes,
including create account, remove account, and change
of username, permission
password-changed
Notify when the user account password changes
config-import
Notify when the system configuration is imported
ssl-certificated-changed
Notify when system certification changes
log-capacity
Notify when the system log reaches the capacity
threshold
power-on
Notify when the power supply is on
power-off
Notify when the power supply is on
di-on
Notify when the digital input is on
di-off
Notify when the digital input is off
action
Set action for event notification
trap
Set trap action for notification
email
Set email action for notification
mgmt-relay
Set MGMT relay action for notification
pwr1-relay
Set PWR1 relay action for notification
pwr2-relay
Set PWR2 relay action for notification
Defaults
All configuration, trap, email event notifications are enabled by default
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
moxa# config
moxa(config)# event-notification general-event all action trap
moxa(config)# no event-notification general-event all action trap email
Error Messages
N/A
Related Commands
show event-notification
event-notification poe-event
event-notification port-event
event-notification switching-event
Moxa Command Line Interface Commands
3-161
Configure Notification for PoE Event
Commands
event-notification poe-event all
event-notification poe-event pd-power-on
event-notification poe-event all action trap mgmt-relay
event-notification poe-event pd-power-on action email pwr1-relay
no event-notification poe-event all
no event-notification poe-event cold-start action email pwr2-relay
Syntax Description
no
Disable the configuration/delete the entry/reset to
default value
event-notification
Configure event notification
poe-event
Configure notifications for PoE events
all
Notify for all PoE events
pd-power-on
Notify when a powered device powers on
pd-power-off
Notify when a powered device powers off
low-input-voltage
Notify when the input voltage from the power sourcing
equipment is low
pd-over-current
Notify when the current exceeds the threshold
pd-no-response
Notify when the device does not receive a response from
the powered device
over-power-budget-limit
Notify when the PoE power consumption exceeds the
budget
power-detection-failure
Notify when a power failure is detected
action
Set action for event notification
trap
Set trap action for notification
email
Set email action for notification
mgmt-relay
Set MGMT relay action for notification
pwr1-relay
Set PWR1 relay action for notification
pwr2-relay
Set PWR2 relay action for notification
Defaults
All configuration, trap, email event notifications are enabled by default
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
moxa# config
moxa(config)# event-notification poe-event all action trap
moxa(config)# no event-notification poe-event all action trap email
Error Messages
N/A
Related Commands
show event-notification
event-notification general-event
event-notification port-event
event-notification switching-event
Moxa Command Line Interface Commands
3-162
Configure Notification for Port Event
Commands
event-notification port-event all
event-notification port -event cold-start
event-notification port -event all action trap mgmt-relay
event-notification port -event cold-start action email pwr1-relay
no event-notification port -event all
no event-notification port -event cold-start action email pwr2-relay
Syntax Description
no
Disable the configuration/delete the entry/reset
to default value
event-notification
Configure event notifications
port-event
Configure notifications for port events
all
Notify for all port events
port-link-up
Notify when a port link goes up
port-link-down
Notify when a port link goes down
port-shutdown-by-rate-limit
Notify when a port shuts down by rate limit
port-recovery-by-rate-limit
Notify when a port recovers by rate limit
port-shutdown-by-port-security
Notify when a port shuts down by port security
action
Set action for event notification
trap
Set trap action for notification
email
Set email action for notification
mgmt-relay
Set MGMT relay action for notification
pwr1-relay
Set PWR1 relay action for notification
pwr2-relay
Set PWR2 relay action for notification
Defaults
All configuration, trap, email event notifications are enabled by default
Port event notifications for all ports are enabled by default
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
moxa# config
moxa(config)# event-notification port-event all action trap
moxa(config)# no event-notification port-event all action trap email
moxa (config-if)# event-notification port-event all
Error Messages
N/A
Related Commands
show event-notification
event-notification general-event
event-notification poe-event
event-notification switching-event
Moxa Command Line Interface Commands
3-163
Configure Notification for Switching Event Settings
Commands
event-notification switching-event all
event-notification switching -event pd-power-on
event-notification switching -event all action trap mgmt-relay
event-notification switching -event pd-power-on action email pwr1-relay
no event-notification switching -event all
no event-notification switching -event cold-start action email pwr2-relay
Syntax Description
no
Disable the configuration/deletes the
entry/resets to default value
event-notification
Configure event notifications
switching-event
Configure notifications for switching events
all
Notify for all switching events
topology-changed
Notify when the network topology changes
Turbo-ring-topology changed
Notify when the Turbo Ring v2 topology changes
Turbo-chain-topology changed
Notify when the Turbo Chain topology changes
Dual-homing-topology changed
Notify when the dual-homing topology changes
coupling-changed
Notify when the Turbo Ring v2 coupling changes
master-changed
Notify when the Turbo Ring v2 master changes
master-mismatched
Notify when the Turbo Ring v2 master
mismatches
rstp-topology-changed
Notify when the RSTP network topology changes
rstp-root-changed
Notify when the RSTP root device changes
rstp-migration
Notify for RSTP migration
rstp-invalid-bpdu
Notify when the RSTP device receives an invalid
BPDU
rstp-new-port-role
Notify when the RSTP port role changes
redundant-port-health-check-fail
Notify when the redundant port health check fails
dual-homing-path-changed
Notify when the dual homing path changes
dot1x-auth-fail
Notify when 802.1x authentication fails
lldp-table-changed
Notify when the LLDP remote table changes
rmon-raising-alarm
Notify when RMON alarm variables values reach
or exceed the raising threshold
rmon-falling-alarm
Notify when RMON alarm variables values reach
or fall below the falling threshold
action
Set action for event notification
trap
Set trap action for notification
email
Set email action for notification
mgmt-relay
Set MGMT relay action for notification
pwr1-relay
Set PWR1 relay action for notification
pwr2-relay
Set PWR2 relay action for notification
Defaults
All configuration, trap, email event notifications are enabled by default
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
moxa# config
moxa(config)# event-notification switching-event all action trap
moxa(config)# no event-notification switching -event all action trap email
Error Messages
N/A
Related Commands
show event-notification
event-notification general-event
event-notification poe-event
event-notification port-event
Moxa Command Line Interface Commands
3-164
Relay Alarm Cut-off
Configure Relay Alarm Cut-off Settings
Commands
relay alarm cut-off mgmt-relay
relay alarm cut-off pwr1-relay
relay alarm cut-off pwr2-relay
Syntax Description
relay
Configure relay parameters
alarm
Configure the relay alarm
cut-off
Configure the relay alarm cut-off
mgmt-relay
Cut off the mgmt-relay alarm
pwr1-relay
Cut off the pwr1-relay alarm
pwr2-relay
Cut off the pwr2-relay alarm
Defaults
N/A
Command Modes
Global
Usage Guidelines
N/A
Examples
moxa# relay alarm cut-off mgmt-relay
Error Messages
N/A
Related Commands
N/A
Email Notification
Configure Email Notification Server
Command
email-notification server server-address <ucast_addr> [server-port <integer(1-65535)>] username
<string(60)> password <string(60)>
Syntax Description
email-notification
Configure email notification parameters
server
Configure server parameters
server-address
Configure the email notification server IP address
server-port
Configure the email-notification server port
username
Configure the email notification server username
password
Configure the email notification server password
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
(config)# email-notification server-address 1.2.3.4 username aaa password bbb
Error messages
N/A
Related commands
N/A
Moxa Command Line Interface Commands
3-165
Configure Email Notification Sender
Commands
email-notification sender <string (60)>
Syntax Description
email-notification
Configure email notification parameters
sender
Configure the email notification sender’s email address
string (60)
The sender’s email address up to 60 characters
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
(config)# email-notification sender [email protected]
Error messages
Invalid Email Format
Related commands
N/A
Configure Email Notification Server TLS Mode Setting
Commands
email-notification server tls {enable | disable}
Syntax Description
email-notification
Configure email notification parameters
server
Configure server parameters
tls
Configure the email notification server TLS mode
enable
Enable the TLS mode
disable
Disable the TLS mode
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
(config)# mail-server server tls enable
(config)# mail-server server tls disable
Error messages
N/A
Related commands
N/A
Configure Email Notification Receiver
Commands
email-notification receiver <string (60)> index <integer (1-5)>
no email-notification receiver index <integer (1-5)>
Syntax Description
no
Disable the configuration/delete the entry/reset to default
value
email-notification
Configure email notification parameters
receiver
Configure the email notification receiver
index
Configure the index of the receiver
string (60)
The receiver’s name up to 60 characters
integer (1-5)
The number index of the receiver ranging from 1 to 5
Defaults
N/A
Command Modes
Global configuration
Usage Guidelines
N/A
Examples
(config)# email-notification receiver testuser@test.com index 1
(config)# no email-notification receiver index 1
Error Messages
Invalid Email Format
Related Commands
N/A
Moxa Command Line Interface Commands
3-166
Show Email Notification Server
Commands
show email-notification server
Syntax Description
show
Display the configuration/statistics/general information
email-notification
Display email notification parameters
server
Display server parameters
Defaults
N/A
Command Modes
Privileged EXEC / User EXEC
Usage Guidelines
N/A
Examples
# show email-notification server
Error Messages
N/A
Related Commands
N/A
Syslog
Configure Logging Server
Commands
logging-server <short(1-3)> { ipv4 <ucast_addr> | <dns_host_name> } [ port <integer(1-65535)>]
Syntax Description
logging-server
Configure logging server parameters
short (1-3)
The index of the syslog server
ipv4
Configure IPv4 parameters
ucast_addr
The IP address
dns_host_name
The host domain name
port
Configure port parameters
integer (1-65535)
The port number
Defaults
N/A
Command Modes
Privileged EXEC
Global Configuration
Usage Guidelines
N/A
Examples
moxa(config)# logging-server 1 ipv4 10.128.1.8 port 514
Error Messages
'Invalid: The server addresses are duplicated.'
'Invalid: The syslog server address cannot be empty if it is enabled.'
Related Commands
no logging-server <short(1-3)>
show logging server
Moxa Command Line Interface Commands
3-167
Delete Logging Server
Commands
no logging-server <short(1-3)> [ enable ]
Syntax Description
no
Remove configuration / delete entry / reset to default value
logging-server
Configure logging server parameters
short (1-3)
The index of the syslog server
enable
Disable this server entry
Defaults
N/A
Command Modes
Global Configuration
Usage Guidelines
N/A
Examples
moxa(config)# no logging-server 1
Error Messages
N/A
Related Commands
logging-server <short(1-3)> {ipv4 <ucast_addr> | <dns_host_name>} [ port
<integer(1-65535)>]
show logging syslog-server
Enable/Disable Logging Syslog Server
Commands
logging syslog-server { enable | disable }
Syntax Description
logging
Configure logging parameters
syslog-server
Configure the syslog server
enable
Enable the syslog server
disable
Disable the syslog server
Defaults
N/A
Command Modes
Global Configuration
Usage Guidelines
N/A
Examples
moxa(config)# logging syslog-server { enable | disable }
Error Messages
'Invalid: The server addresses are duplicated.'
'Invalid: The syslog server address cannot be empty if it is enabled.'
Related Commands
show logging server
Moxa Command Line Interface Commands
3-168
Show Syslog Server Configuration
Commands
show logging syslog-server
Syntax Description
show
Display configuration/status information
logging
Display logging information
syslog-server
Display syslog server information
Defaults
N/A
Command Modes
Privileged EXEC / User EXEC
Examples
moxa# show logging syslog-server
Syslog Server Configuration
Syslog Enable: disable
Index Server Address Port Status
----- -------------------------------- ----- -----
1 111.2.21.1 514 enable
2 200.2.2.2 2540 enable
3 disable
Help Message
Display the Syslog logging server table
Error Messages
N/A
Related Commands
logging server enable
logging-server <short(1-3)> {ipv4 <ucast_addr> | <dns_host_name>} [ port
<integer(1-65535)>]
Moxa Command Line Interface Commands
3-169
Diagnosis
LLDP
Show LLDP Information
Commands
show lldp
Syntax Description
show
Display configuration/statistics/general information
lldp
Display global LLDP information
Defaults
N/A
Command Modes
Privileged EXEC
User EXEC
Usage Guidelines
Display the global LLDP settings
Examples
moxa# show lldp
LLDP is disabled
Transmit Interval : 30
Holdtime Multiplier : 4
Reinitialization Delay : 2
Tx Delay : 2
Notification Interval : 5
Chassis Id SubType : Mac Address
Chassis Id : 00:01:02:03:04:05
Error Messages
N/A
Related Commands
config lldp {enable | disable}
config lldp chassis-id-subtype { chassis-comp <string(255)> | if-alias | port-comp
<string(255)> | mac-addr | nw-addr | if-name | local <string(255)> }
config lldp holdtime-multiplier <2-10>
config lldp notification-interval <seconds(5-3600)>
config lldp reinitialization-delay <seconds(1-10)>
config lldp transmit-interval <seconds(5-32768)>
config lldp tx-delay (1-8192)
Moxa Command Line Interface Commands
3-170
Show LLDP Interface
Commands
show lldp interface
Syntax Description
show
Display configuration/statistics/general information
lldp
Display the LLDP interface status
interface
Show the LLDP interface information
Defaults
N/A
Command Modes
Privileged EXEC
User EXEC
Usage Guidelines
Display LLDP port interface information
Examples
moxa#show lldp interface
Eth1/3:
Tx State : Enabled
Rx State : Enabled
Tx SEM State : INITIALIZE
Rx SEM State : WAIT PORT OPERATIONAL
Notification Status : Enabled
Notification Type : Remote Table Chang
DestinationMacAddr : 01:80:c2:00:00:0e
Error Messages
N/A
Related Commands
show lldp
config-if > lldp {transmit | receive}
config-if > lldp dest-mac <mac_addr>
Moxa Command Line Interface Commands
3-171
Show LLDP Neighbors
Commands
show lldp neighbors
Syntax Description
show
Display configuration/statistics/general information
ldp
Display the LLDP interface status
neighbors
Display the LLDP remote interface database
Defaults
N/A
Command Modes
Privileged EXEC
User EXEC
Usage Guidelines
Display LLDP neighbor interface information
Examples
moxa# show lldp neighbors
Capability Codes :
(R) Router, (B) Bridge, (T) Telephone, (C) DOCSIS Cable Device,
(W) WLAN Access Point, (P) Repeater, (S) Station, (O) Other
Chassis Id SubType : Mac Address
Chassis Id : 00:90:e8:10:20:30
Port Id SubType : Local
Port Id : 1
Port Description : 1000TX,RJ45.
System Name : --
System Desc : EDS-G512E
Local Intf : Eth1/3
Time Remaining : 19 Seconds
System Capabilities Supported : B
System Capabilities Enabled : B
Management Addresses :
IfId SubType Address OID
……
Error Messages
N/A
Moxa Command Line Interface Commands
3-172
Show LLDP Statistics
Commands
Show lldp statistics
Syntax Description
show
Display configuration/statistics/general information
lldp
Display the LLDP interface LLDP status
statistics
Display LLDP remote table statistics information
Defaults
N/A
Command Modes
Privileged EXEC
User EXEC
Usage Guidelines
Display LLDP statistics for the local counter
Examples
moxa# show lldp statistics
Remote Table Last Change Time : 182700
Remote Table Inserts : 2
Remote Table Deletes : 0
Remote Table Drops : 0
Remote Table Ageouts : 0
Remote Table Updates : 0
Error Messages
N/A
Related Commands
show lldp
Show LLDP Error
Commands
show lldp error
Syntax Description
show
Display configuration/statistics/general information
lldp
Configure LLDP parameters
error
Display LLDP error information such as memory allocation failures,
queue overflows, and table overflows
Defaults
N/A
Command Modes
Privileged EXEC
User EXEC
Usage Guidelines
Display the LLDP error counter
Examples
moxa# show lldp errors
Total Memory Allocation Failures : 0
Total Input Queue Overflows : 0
Total Table Overflows : 0
Error Messages
N/A
Related Commands
show lldp
config lldp enable
config-if lldp tlv-select basic-tlv
config-if lldp tlv-select dot1t1v
config-if lldp tlv-select dot3tlv
Moxa Command Line Interface Commands
3-173
Show LLDP Traffic
Commands
show lldp traffic
Syntax Description
show
Display configuration/statistics/general information
lldp
Display the LLDP interface status
traffic
Display the LLDP local traffic
Defaults
N/A
Command Modes
Privileged EXEC
User EXEC
Usage Guidelines
Display LLDP traffic for the local counter
Examples
moxa# show lldp traffic
Total Frames Out : 82
Total Entries Aged : 0
Total Frames In : 81
Total Frames Received In Error : 81
Total Frames Discarded : 0
Total TLVS Unrecognized : 324
Total TLVs Discarded : 0
Total PDU length error Drops : 0
Error Messages
N/A
Related Commands
show lldp
config-if > lldp {transmit | receive}
config-if > lldp dest-mac <mac_addr>
Enable/Disable LLDP Function
Commands
lldp enable
lldp disable
Syntax Description
lldp
Configure LLDP parameters
enable
Enable LLDP
disable
Disable LLDP
Defaults
Enable
Command Modes
Privileged EXEC
Global Configuration
Usage Guidelines
Enable or disable global LLDP
Examples
moxa (config)# lldp enable
moxa (config)# lldp disable
Error Messages
N/A
Related Commands
show lldp
show lldp interface
show lldp neighbors
show lldp traffic
show lldp errors
show lldp statistics
Moxa Command Line Interface Commands
3-174
Configure Global LLDP Timer Interval
Commands
lldp transmit-interval <seconds (5-32768)>
no lldp transmit-interval
Syntax Description
no
Remove configuration/delete entry/reset to default value
lldp
Configure LLDP parameters
transmit-interval
Configure the transmit interval
seconds
The interval time ranging from 5 to 32768 seconds
Defaults
The interval between successive transmit cycles is set to 30 seconds by default
Command Modes
Privileged EXEC
Global Configuration
Usage Guidelines
Configure the global LLDP transmit interval time
Examples
moxa(config)# lldp transmit-interval 30
moxa(config)# no lldp transmit-interval
Error Messages
N/A
Related Commands
show lldp
config lldp enable
Configure LLDP Holdtime Multiplier
Commands
lldp holdtime-multiplier <value (2-10)>
no lldp holdtime-multiplier
Syntax Description
no
Remove configuration/delete entry/reset to default value
lldp
Configure LLDP parameters
holdtime-multiplier
A multiplier on the transmit-interval used to compute the
TTL value of txTTL.
value
The multiplier value ranging from 2 to 10
Defaults
The default holdtime multiplier is set to 4
Command Modes
Privileged EXEC
Global Configuration
Usage Guidelines
N/A
Examples
moxa(config)# lldp holdtime-multiplier 4
moxa(config)# no lldp holdtime-multiplier
Error Messages
N/A
Related Commands
show lldp
config lldp enable
config lldp tx-delay
Moxa Command Line Interface Commands
3-175
Configure LLDP Transmission Delay Time
Commands
lldp tx-delay <seconds (1-8192) // tx_delay <= (0.25 x transmit-interval)
no lldp tx-delay
Syntax Description
no
Remove configuration/delete entry/reset to default value
lldp
Configure LLDP parameters
tx-delay
Configure the minimum delay between successive LLDP frame
transmissions
seconds
The transmission delay time in seconds ranging from 1 to 8192
Defaults
The default LLDP transmission delay time is set to 2 seconds
Command Modes
Privileged EXEC
Global Configuration
Usage Guidelines
Configure the LLDP tx-delay parameter
Examples
moxa(config)# lldp tx-delay 4
moxa(config)# no lldp tx-delay
Error Messages
"Invalid: Tx Delay should be less than or equal to the value = 0.25 * Transmit Interval."
Related Commands
show lldp
config lldp enable
config lldp transmit-interval
Configure LLDP Reinitialization Delay Time
Commands
lldp reinitialization-delay <seconds (1-10)>
no lldp reinitialization-delay
Syntax Description
no
Remove configuration/delete entry/reset to default value
lldp
Configure LLDP parameters
reinitialization-delay
Configure the delay after admin status becomes ‘disabled’
before re-initialization is attempted
seconds
The reinitialization delay ranging from 1 to 10 seconds
Defaults
The default reinitialization delay time is set to 2 seconds
Command Modes
Privileged EXEC
Global Configuration
Usage Guidelines
Configure the LLDP re-initialization delay time
Examples
moxa(config)# lldp reinitialization-delay 4
moxa(config)# no lldp reinitialization-delay
Error Messages
N/A
Related Commands
show lldp
config lldp enable
Moxa Command Line Interface Commands
3-176
Configure LLDP Notification Interval Time
Commands
lldp notification-interval <seconds(5-3600)>
no lldp notification-interval
Syntax Description
no
Remove configuration/delete entry/reset to default value
lldp
Configure LLDP parameters
notification-interval
Configure lldpRemTableChange event notifications
seconds
The notification interval ranging from 5 to 3600 seconds
Defaults
The default notification interval time is set to 5 seconds
Command Modes
Privileged EXEC
Global Configuration
Usage Guidelines
Configure the LLDP notification interval time
Examples
moxa(config)# lldp notification-interval 5
moxa(config)# no lldp notification-interval
Error Messages
N/A
Related Commands
show lldp
config lldp enable
Configure LLDP Global Setting
Commands
lldp chassis-id-subtype { chassis-comp <string(255)> | if-alias | port-comp <string(255)> | mac-addr |
nw-addr | if-name | local <string(255)> }
Syntax Description
lldp
Configure LLDP parameters
chassis-id-subtype
Configure chassis-component and local system sybtypes
chassis-comp
Represents a chassis identifier based on the value of
entPhysicalAlias object for a chassis component
if-alias
Represents a chassis identifier based on the value of ifAlias
for an interface on the containing chassis
port-comp
Represents a chassis identifier based on the value of
entPhysicalAlias object for a port or backplane within the
chassis
mac-addr
Represents a chassis identifier based on the value of a
unicast source address of a port on the chassis
nw-addr
Represents a chassis identifier based on a network address
associated with a particular chassis. The encoded address is
actually composed of two fields. The first field is a single
octet, representing the IANA AddressFamilyNumbers value
for the specific address type, and the second field is the
network address value.
if-name
Represents a chassis identifier based on the value of a
ifName pbject for an interface on the containing chassis
local
Represents a chassis identifier based on a locally defined
value.
Defaults
mac-addr use sys_mac, others are none.
Command Modes
Privileged EXEC
Global Configuration
Usage Guidelines
Configure the LLDP chassis ID subtype parameters
Examples
moxa (config)# lldp chassis-id-subtype chassis-comp moxa
Error Messages
N/A
Related Commands
show lldp
show lldp local
config lldp enable
Moxa Command Line Interface Commands
3-177
Configure LLDP Port Setting
Commands
lldp {transmit | receive}
no lldp {transmit | receive}
Syntax Description
no
Remove configuration/delete entry/reset to default value
lldp
Configure LLDP parameters
transmit
Enable the transmission of LLDPDU from one of the ports of the
server to the LLDP module
receive
Enable the reception of LLDPDU from one of the ports of the server
to the LLDP module
Defaults
mac-addr use sys_mac
LLPDU transmitting and receiving are both enabled by default
Command Modes
Privileged EXEC
Interface Configuration
Usage Guidelines
Configure the LLDP TX or RX for the port interface
Examples
moxa(config-if)# lldp transmit
moxa(config-if)# no lldp transmit
Error Messages
N/A
Related Commands
show lldp
show lldp interface
Configure LLDP Port ID Subtype
Commands
lldp port-id-subtype { if-alias | port-comp <string(255)> | mac-addr | if-name | local <string(255)> }
Syntax Description
lldp
Configure LLDP parameters
port-id-subtype
Configure LLDP port subtype
if-alias
Represents a chassis identifier based on the value of ifAlias for an
interface on the containing chassis
port-comp
Represents a chassis identifier based on the value of
entPhysicalAlias object for a port or backplane within the chassis
mac-addr
Represents a chassis identifier based on the value of a unicast
source address, of a port on the chassis
if-name
Represent a chassis identifier based on the value of a ifName pbject
for an interface on the containing chassis
local
Represent a chassis identifier based on a locally defined value.
Defaults
mac-addr use sys_mac, others are none.
Command Modes
Privileged EXEC
Global Configuration
Usage Guidelines
Configure the LLDP notification interval time
Examples
moxa(config)# lldp notification-interval 5
moxa(config)# no lldp notification-interval
Error Messages
N/A
Related Commands
show lldp
config lldp enable
Moxa Command Line Interface Commands
3-178
Configure LLDP TLV Setting
Commands
lldp tlv-select basic-tlv { port-descr | sys-name | sys-descr | sys-capab |}
Syntax Description
lldp
Configure LLDP parameters
tlv-select
Configure the transmission basic LLDP TLVs
basic-tlv
Configure basic TLVs
port-descr
Enable basic TVLs transmission for the administratively assigned
description for the port
sys-name
Enable basic TLV transmission for the administratively assigned
system name
sys-descr
Enable basic TLV transmission for the administratively assigned
system description
sys-capab
Enable the system capabilities of the basic TLV transmission
Defaults
mac-addr use sys_mac, others are none
Command Modes
Privileged EXEC
Interface Configuration
Usage Guidelines
Configure the LLDP basic TLV
Examples
moxa (config-if)# lldp tlv-select basic-tlv port-descr
moxa (config-if)# no lldp tlv-select basic-tlv port-descr
Error Messages
"Invalid: The format of Basic Transmit TLVs are Port Description, Device Name, Device
Description, and Device Capability."
Related Commands
show lldp local
Configure LLDP TLV DOT1 Setting
Commands
lldp tlv-select dot1tlv { port-vlan-id | {all |<vlan-id>} | vlan-name {all |} | }
Syntax Description
lldp
Configure LLDP parameters
tlv-select
Configure the transmission basic LLDP TLVs
dot1tlv
Configure specific 802.1 TLVs
port-vlan-id
Specify the VLAN ID of the port that uniquely identifies a specific
VLAN. The VLAN ID is associated with a specific group of protocols
for the specific port.
protocol-vlan-id
Specify the Protocol ID that represents a specific group of protocols
that are associated together when assigning a VID to a frame. This
group ID is associated with the specific port.
All : Set the protocol ID as all
vlan-id : Set the protocol ID as the mentioned vlan ID
Only work for the 2009 version.
vlan-name
Specify the administratively assigned VLAN string.
Defaults
N/A.
Command Modes
Privileged EXEC
Interface Configuration
Usage Guidelines
Configure LLDP DOT1 TLV
Examples
moxa (config-if)# lldp tlv-select dot1tlv port-vlan-id
moxa (config-if)# no lldp tlv-select dot1tlv port-vlan-id
Error Messages
N/A
Related Commands
show lldp local
show lldp neighbors
show lldp errors
Moxa Command Line Interface Commands
3-179
Configure LLDP TLV DOT3 Setting
Commands
lldp tlv-select dot3tlv { link-aggregation | max-framesize }
Syntax Description
lldp
Configure LLDP parameters
tlv-select
Configure the transmission basic LLDP TLVs
dot3tlv
Configure specific 802.3 TLVs
link-aggregation
Configure the link aggregation protocol statistics for each port on
the device
Max-framesize
The maximum frame size of the TLV
Defaults
N/A.
Command Modes
Privileged EXEC
Interface Configuration
Usage Guidelines
Configure the LLDP DOT3 TLV
Examples
moxa (config-if)# lldp tlv-select dot3tlv macphy-config
moxa (config-if)# no lldp tlv-select dot3tlv macphy-config
Error Messages
"Invalid: The value of 802.3 Trasmit TLVs capability are Link Aggregation Stastictis and
Maximum Frame Size."
Related Commands
show lldp local
show lldp neighbors
show lldp errors
Port Mirror
Enable/Disable Mirroring
Commands
port-mirror {enable | disable}
Syntax Description
port-mirror
Configure port mirror parameters
enable
Enable mirroring in the system
disable
Disable mirroring in the system
Defaults
Port mirroring is enabled by default
Command Modes
Global Configuration Mode
Usage Guidelines
N/A
Examples
moxa# configure
moxa(config)# port-mirror enable
moxa# configure
moxa(config)# port-mirror disable
Error Messages
N/A
Related Commands
moxa# show monitor { session <session-id (1-5)> | range <session-list> }
Moxa Command Line Interface Commands
3-180
Show Mirroring Information
Commands
show monitor { session <session-id (1-5)> | range <session-list> }
Syntax Description
show
Display configuration/status information
monitor
Display port mirror information
session
The mirroring information related to a specific session
session-id
The index of the mirroring session
range
The mirroring information for the specified list of mirroring sessions
session-list
The session list
Defaults
N/A
Command Modes
Privileged EXEC Mode
Usage Guidelines
N/A
Examples
moxa# show monitor session 1
Mirroring is globally Enabled.
Session : 1
-------
Source Ports
Rx : None
Tx : None
Both : Eth1/1
Destination Ports : Eth1/2
Session Status : Active
moxa# show monitor range 1-5
Mirroring is globally Enabled.
Session : 1
-------
Source Ports
Rx : None
Tx : None
Both : Eth1/1
Destination Ports : Eth1/2
Session Status : Active
Session : 2
-------
Source Ports
Rx : None
Tx : None
Both : Eth1/3
Destination Ports : Eth1/4
Session Status : Active
% Session 3 does not exist
% Session 4 does not exist
% Session 5 does not exist
Error Messages
% Invalid: Monitor session range must be in between (1-5)
Example: Key “range 1-6”
% Invalid: Invalid Session List
Example: Key “range 0-5”
Related Commands
N/A
Moxa Command Line Interface Commands
3-181
Configure the Source for a Mirroring Session
Commands
monitor session <session-id (1-5)> { source { interface <interface-type> <interface-id> [{ rx | tx |
both }]}}
Syntax Description
monitor
Configure port mirroring parameters
session
Configure the mirroring session
session-id
The index of the mirroring session
source
Configure the mirroring source port
interface
Configure the interface
interface-type
The interface type
interface-id
The interface number
rx, tx, both
Mirror received, transmitted, or both types of traffic
Defaults
The traffic type to mirror is set to both by default
Command Modes
Global Configuration Mode
Usage Guidelines
N/A
Examples
moxa# configure
moxa(config)# monitor session 1 source interface ethernet 1/1
moxa# configure
moxat(config)# monitor session 1 source interface ethernet 1/1 rx
moxa# configure
moxa(config)# monitor session 1 source interface ethernet 1/1 tx
Error Messages
% Invalid: Duplicate Rx Source Port.
% Invalid: Duplicate Tx Source Port.
% Invalid: Destination Port conflicts with Tx Source Port or Rx Source Port.
% Invalid: Exceed Max Mirror Port.
% Invalid: If the port is a Port-Channel member, it cannot be set to the destination port,
RX source port, or TX source port.
Related Commands
moxa(config)# no monitor session <session-id (1-5)> { source { interface
<interface-type> <interface-id> }}
Remove Source Port Configurations for a Mirroring Session
Commands
no monitor session <session-id (1-5)> { source { interface <interface-type> <interface-id> }}
Syntax Description
no
Remove configuration/delete entry/reset to default value
monitor
Configure port mirroring parameters
session
Configure the mirroring session
session-id
The index of the mirroring session
source
Configure the mirroring source port
interface
Configure the interface
interface-type
The interface type
interface-id
The interface number
Defaults
N/A
Command Modes
Global Configuration Mode
Usage Guidelines
N/A
Examples
moxa# configure
moxa(config)# no monitor session 1 source interface ethernet 1/1
Error Messages
N/A
Related Commands
moxa(config)# monitor session <session-id (1-5)> { source { interface
<interface-type> <interface-id> [{ rx | tx | both }]}}
Moxa Command Line Interface Commands
3-182
Configure the Destination for a Mirroring Session
Commands
monitor session <session-id (1-5)> destination { interface <interface-type> <interface-id>}
Syntax Description
monitor
Configure port mirroring parameters
session
Configure the mirroring session
session-id
The index of the mirroring session
destination
Configure the mirroring destination port
interface
Configure the interface
interface-type
The interface type
interface-id
The interface number
Defaults
N/A
Command Modes
Global Configuration Mode
Usage Guidelines
N/A
Examples
moxa# configure
moxa(config)# monitor session 1 destination interface ethernet 1/1
Error Messages
% Invalid: Duplicate Destination Port.
% Invalid: Destination Port conflicts with Tx Source Port or Rx Source Port.
% Invalid: If the port is a Port-Channel member, it cannot be set to the destination port,
RX source port, or TX source port.
% Invalid: If the port is set as the ring port of Turbo Ring v2, it cannot be set to the
destination port.
% Invalid: If the port is set as the coupling port of Turbo Ring v2, it cannot be set to the
destination port.
% Invalid: If the port is set as the Turbo Chain head/tail/member port, it cannot be set
to the destination port.
% Invalid: If the port is set as the RSTP port, it cannot be set to the destination port.
% Invalid: If the port is set as the Dual Homing redundant port, it cannot be set to the
destination port.
Related Commands
moxa(config)# no monitor session <session-id (1-5)> destination { interface
<interface-type> <interface-id>}
Delete the Destination Configuration for a Mirroring Session
Commands
no monitor session <session-id (1-5)> destination { interface <interface-type> <interface-id>}
Syntax Description
no
Remove configuration/delete entry/reset to default value
monitor
Configure port mirroring parameters
session
Configure the mirroring session
session-id
The index of the mirroring session
destination
Configure the mirroring destination port
interface
Configure the interface
interface-type
The interface type
interface-id
The interface number
Defaults
N/A
Command Modes
Global Configuration Mode
Usage Guidelines
N/A
Examples
moxa# configure
moxa(config)# no monitor session 1 destination interface ethernet 1/1
Error Messages
N/A
Related Commands
moxa(config)# monitor session <session-id (1-5)> destination { interface
<interface-type> <interface-id>}
Moxa Command Line Interface Commands
3-183
Delete Mirroring Configurations
Commands
no monitor session { range <session-list> | session-id (1-5)}
Syntax Description
no
Remove configuration/delete entry/reset to default value
monitor
Configure port mirroring parameters
session
Configure the mirroring session
range
The list of sessions for which the mirroring configuration should be
removed
session-list
The session list
session-id
The index of the mirroring session
Defaults
N/A
Command Modes
Global Configuration Mode
Usage Guidelines
N/A
Examples
moxa# configure
moxa(config)# no monitor session 1
moxa# configure
moxa(config)# no monitor session range 1-5
Error Messages
% Invalid: Monitor session range must be in between (1-5)
Example: Key “range 1-6”
% Invalid: Invalid Session List
Example: Key “range 0-5”
Related Commands
N/A
Moxa Command Line Interface Commands
3-184
Ping
Ping the Host
Commands
ping host [ repeat repeat-count ] [ size payload-size ] [ timeout request-timeout ]
Syntax Description
ping
Ping a target to check its status
host
The IP address or domain name of the node to be pinged
repeat
The number of ping packets that are sent to the destination
address
repeat-count
The repeat value
size
The ize of the ping packet
payload-size
The length of the ping packet value
timeout
The time in seconds after which the entity waiting for the ping
response times out
request-timeout
The timeout value
Defaults
N/A
Command Modes
User EXEC
Privileged EXEC
Usage Guidelines
N/A
Examples
moxa# ping 192.168.127.254 repeat 5
PING 192.168.127.254 (192.168.127.254) 56(84) bytes of data.
64 bytes from 192.168.127.254: icmp_seq=1 ttl=64 time=1.52 ms
64 bytes from 192.168.127.254: icmp_seq=2 ttl=64 time=0.803 ms
64 bytes from 192.168.127.254: icmp_seq=3 ttl=64 time=0.879 ms
64 bytes from 192.168.127.254: icmp_seq=4 ttl=64 time=0.791 ms
64 bytes from 192.168.127.254: icmp_seq=5 ttl=64 time=0.845 ms
--- 192.168.127.254 ping statistics ---
5 packets transmitted, 5 received, 0% packet loss, time 4002ms
rtt min/avg/max/mdev = 0.791/0.968/1.523/0.279 ms
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-185
ARP Table
Show IP ARP Table
Commands
show ip arp
Syntax Description
show
Display configuration/status information
ip
Display IP information
arp
Display the ARP table
Defaults
N/A
Command Modes
User EXEC
Privileged EXEC
Usage Guidelines
N/A
Examples
moxa# show ip arp
IP Address MAC Address
--------------- -----------------
192.168.127.113 00:05:1b:a1:ae:62
192.168.127.112 00:05:1b:a3:53:d6
Error Messages
N/A
Related Commands
N/A
Event Log
Show Logging Event Log
Commands
show logging event-log
Syntax Description
show
Display configuration/status information
logging
Display logging information
event-log
Display event log entries
Defaults
N/A
Command Modes
Privileged EXEC / User EXEC
Examples
moxa# show logging event-log
Total number of log entries = 7
Boot SEV Timestamp Message
----- ---- -------------------- ----------
19 5 2018-02-05 12:00:51 [Account:admin] successfully logged in via local.
19 5 2018-02-05 12:00:14 Port 7/4 link up.
19 5 2018-02-05 12:00:12 Port 7/1 link up.
19 5 2018-02-05 12:00:11 Port 7/2 link up.
19 5 2018-02-05 12:00:11 System has performed a warm start.
19 5 2018-02-05 12:00:09 Port 4/3 link up.
19 5 2018-02-05 12:00:08 Port 4/4 link up.
Help Message
Display the log entries information
Error Messages
N/A
Related Commands
clear logging event-log
Moxa Command Line Interface Commands
3-186
Show Logging Log Capacity
Commands
show logging log-capacity
Syntax Description
show
Display configuration/status information
logging
Display logging information
log-capacity
Display log capacity information
Defaults
N/A
Command Modes
Privileged EXEC / User EXEC
Usage Guidelines
N/A
Examples
moxa# show logging log-capacity
Error Messages
N/A
Related Commands
N/A
Clear Logging Event Log
Commands
clear logging event-log
Syntax Description
clear
Clear the event
logging
Display logging information
event-log
The local event log entries to be cleared
Defaults
N/A
Command Modes
Privileged EXEC
Usage Guidelines
N/A
Examples
moxa# clear logging event-log
Error Messages
N/A
Related Commands
show logging event-log
Export Event Log File
Commands
copy event-log {tftp://server/filename | sftp://<user-name>:<pass-word>@server/filename}
Syntax Description
copy
Copy the target file or input
event-log
The system event log
tftp://server/filename
The address of the remote TFTP server in the format
"tftp://server/filename"
sftp://<username>:<password>
@server/filename
The address of the remote SFTP server in the format
"sftp://username:password@server/filename"
Defaults
N/A
Command Modes
Privileged EXEC
Usage Guidelines
N/A
Examples
moxa# copy event-log tftp://192.168.127.11/test1.log
Help Message
Copy the system logs to a remote site
Error Messages
N/A
Related Commands
show logging event-log
Moxa Command Line Interface Commands
3-187
Configure Event Log Capacity Settings
Commands
logging log-capacity threshold <short (50-100)>
Syntax Description
logging
Configure logging parameters
log-capacity
Configure the log capacity
threshold
Configure the log capacity threshold
short (50-100)
The log capacity threshold in percentage
Defaults
The default log threshold is set to 80 entries
Command Modes
Privileged EXEC
Global Configuration
Usage Guidelines
N/A
Examples
moxa(config)# logging log-capacity threshold <short(50-100)>
Error Messages
N/A
Related Commands
N/A
Delete Logging Log Capacity Threshold
Commands
no logging log-capacity threshold
Syntax Description
no
Remove configuration / delete entry / reset to default value
logging
Configure logging parameters
log-capacity
Configure the log capacity
threshold
Configure the log capacity threshold
Defaults
The default log threshold is set to 80 entries
Command Modes
Privileged EXEC
Global Configuration
Usage Guidelines
N/A
Examples
moxa(config)# no logging log-capacity threshold
Error Messages
N/A
Related Commands
logging log-capacity threshold
Configure Oversized Log Action Setting
Commands
logging oversize-action { overwrite-oldest | stop-recording }
Syntax Description
logging
Configure logging parameters
oversize-action
Configure the action when exceeding the log threshold
overwrite-oldest
Overwrite the oldest entry
stop-recording
Stop recording events
Defaults
N/A
Command Modes
Privileged EXEC
Global Configuration
Usage Guidelines
N/A
Examples
moxa(config)# logging oversize-action { overwrite-oldest | stop-recording }
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-188
Copy Event Log
Commands
copy event-log { <tftp_url> | <sftp_url> }
Syntax Description
copy
Copy the target file or input
event-log
The system event log
tftp_url
The address of the remote TFTP server in the format
"tftp://server/filename"
sftp_url
The address of the remote SFTP server in the format
"sftp://username:password@server/filename"
Defaults
N/A
Command Modes
Privileged EXEC
Usage Guidelines
N/A
Examples
moxa# copy event-log tftp://www.test.com
Error messages
N/A
Related commands
N/A
Maintenance and Tool
Locator
Show the Locator
Commands
locator [ duration ]
Syntax Description
locator
Activate the device locator so that the LED on the device blinks
duration
The duration of locator activation in seconds
Defaults
The locator duration is set to 60 seconds by default
Command Modes
Privileged EXEC
Usage Guidelines
N/A
Examples
moxa# locator 100
Error Messages
N/A
Related Commands
N/A
Reboot
Reboot the Switch
Commands
reload
Syntax Description
reload
Perform a warm restart
Defaults
N/A
Command Modes
Privileged EXEC
Usage Guidelines
N/A
Examples
moxa# reload
Are you sure you want to restart the device? [y/N] y
Restarting device...
Error Messages
N/A
Related Commands
N/A
Moxa Command Line Interface Commands
3-189
Reset to Default
Reset to Default
Commands
reload factory default
Syntax Description
reload
Perform a warm restart
factory-default
Perform a warm restart and restore the factory default settings
Defaults
N/A
Command Modes
Privileged EXEC
Usage Guidelines
N/A
Examples
moxa# reload factory-default
Would you like to reset system configuration to factory default? [y/N] y
Resetting device into factory default and restarting...
Error Messages
N/A
Related Commands
N/A
Logout
Commands
exit
Syntax Description
exit
Log out from the device
Defaults
N/A
Command Modes
Privileged EXEC
Usage Guidelines
N/A
Examples
moxa# exit
Error messages
N/A
Related commands
N/A
