Table of Contents
Cover photo may show optional equipment
not supplied with standard unit.
Read the Operator’s manual entirely. When you
see this symbol, the subsequent instructions and
warnings are serious - follow without exception.
Your life and the lives of others depend on it!
!
© Copyright 2015 Printed
22130
320-019M
SH35 Category 1 & 2
Skid Steer Quick Hitch
Operator’s Manual
11/23/15
SH35 Category 1 & 2 Skid Steer Quick Hitch 320-019M
11/23/15
© Copyright 2015 All rights Reserved
Land Pride provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the
preparation of this manual, Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use
of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this
product at the time of its publication, and may not reflect the product in the future.
Land Pride is a registered trademark.
All other brands and product names are trademarks or registered trademarks of their respective holders.
Printed in the United States of America.
Table of Contents
Important Safety Information . . . . . . . . . . . . . 1
Safety at All Times . . . . . . . . . . . . . . . . . . . . . . . . . 1
Look For The Safety Alert Symbol . . . . . . . . . . . . . . 1
Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Using This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Owner Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Further Assistance . . . . . . . . . . . . . . . . . . . . . . . . 5
Section 1: Assembly & Setup . . . . . . . . . . . . . 6
Skid Steer Loader Requirements . . . . . . . . . . . . . . 6
Skid Steer Loader Hook-Up . . . . . . . . . . . . . . . . . . . 6
Center Hook Adjustment . . . . . . . . . . . . . . . . . . . . . 6
Implement Hook-Up . . . . . . . . . . . . . . . . . . . . . . . . 7
Spare Bushings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Implement Unhooking . . . . . . . . . . . . . . . . . . . . . . . 8
Section 2: Operating Instructions . . . . . . . . . 9
Transporting and Use . . . . . . . . . . . . . . . . . . . . . . . 9
Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . 9
Section 3: Maintenance & Lubrication . . . . . 10
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Pivot points . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Section 4: Specifications & Capacities . . . . 11
Section 5: Features & Benefits . . . . . . . . . . . 12
Section 6: Torque Values Chart . . . . . . . . . . 13
Section 7: Warranty . . . . . . . . . . . . . . . . . . . 15
Table of Contents
1
11/23/ 15
SH35 Category 1 & 2 Skid Steer Quick Hitch 320-019M
Important Safety Information
Table of Contents
Important Safety Information
▲
These are common practices that may or may not be applicable to the products described in
this manual.
Safety at All Times
Thoroughly read and understand
the instructions given in this
manual before operation. Refer to
the “Safety Label” section, read all
instructions noted on them.
Do not allow anyone to operate
this equipment who has not fully
read and comprehended this
manual and who has not been
properly trained in the safe
operation of the equipment.
▲ The operator must not use drugs
or alcohol as they can change the
alertness or coordination of that
person while operating equipment.
The operator should, if taking over-
the-counter drugs, seek medical
advice on whether he/she can
safely operate the equipment.
▲ Operator should be familiar with all
functions of the unit.
▲ Make sure all guards and shields
are in place and secured before
operating implement.
▲ Keep all persons away from
equipment and work area.
▲ Start skid steer with steering levers
and hydraulic controls in neutral.
▲ Operate implement and loader
arms from the driver’s seat only.
▲ Dismounting from a moving unit
can cause serious injury or death.
▲ Do not allow anyone to stand
between skid steer and implement
while hooking-up to implement.
▲ Keep hands, feet, and clothing
away from power-driven parts.
▲ Watch out for objects overhead
and along side such as fences,
buildings, wires, trees, limbs, etc.,
while transporting and operating
attached implement.
▲ Detach and store implement in an
area where children normally do
not play. Secure implement by
using blocks and supports.
Look For The Safety Alert Symbol
The SAFETY ALERT SYMBOL indicates there is a
potential hazard to personal safety involved and extra
safety precaution must be taken. When you see this
symbol, be alert and carefully read the message that
follows it. In addition to design and configuration of
equipment, hazard control, and accident prevention are
dependent upon the awareness, concern, prudence, and
proper training of personnel involved in the operation,
transport, maintenance, and storage of equipment.
!
Be Aware of
Signal Words
A Signal word designates a degree or
level of hazard seriousness. The
signal words are:
Indicates an imminently hazardous
situation which, if not avoided, will
result in death or serious injury. This
signal word is limited to the most
extreme situations, typically for
machine components that, for
functional purposes, cannot be
guarded.
!
DANGER
Indicates a potentially hazardous
situation which, if not avoided, could
result in death or serious injury, and
includes hazards that are exposed
when guards are removed. It may also
be used to alert against unsafe
practices.
Indicates a potentially hazardous
situation which, if not avoided, may
result in minor or moderate injury. It
may also be used to alert against
unsafe practices.
!
WARNING
!
CAUTION
Parts Manual QR Locator
The QR (Quick Reference) code on the
cover and to the left will take you to the
Parts Manual for this equipment.
Download the appropriate App on your
smart phone, open the App, point your
phone on the QR code and take a picture.
Dealer QR Locator
The QR code on the left will
link you to available dealers
for Land Pride products.
Refer to Parts Manual QR
Locator on this page for
detailed instructions.
For Your Protection
▲ Thoroughly read and understand
the “Safety Label” section, read
all instructions noted on them.
Avoid Underground
Utilities
▲ Dig Safe, Call 811.
Always contact your local utility
companies (electrical, telephone,
gas, water, sewer, and others)
before digging so that they may
mark the location of any
underground services in the area.
▲ Be sure to ask how close you can
work to the marks they positioned.
2
SH35 Category 1 & 2 Skid Steer Quick Hitch 320-019M
11/23/15
Important Safety Information
Table of Contents
These are common practices that may or may not be applicable to the products described in
this manual.
Transport Safely
▲ Comply with state and local laws.
▲ Never travel at a speed which does
not allow adequate control of
steering and stopping. Some rough
terrains require a slower speed.
▲ Avoid contact with any over head
utility lines or electrically charged
conductors.
▲ Always drive with load on end of
loader arms low to the ground.
▲ Always drive straight up and down
ramps with load on “uphill” side of
skid steer.
▲ Engage park brake when stopped
on an incline.
▲ IMPORTANT: Do not tow a load
that is more than double the weight
of the vehicle towing the load.
▲ Use towing vehicle and trailer of
adequate size and capacity. Secure
equipment towed on a trailer with
tie downs and chains.
▲ Sudden braking can cause a towed
trailer to swerve and upset. Reduce
speed if towed trailer is not
equipped with brakes.
Shutdown and Storage
Before leaving operator’s
seat:
▲ Lower lift arms and put
attachment flat on the ground.
▲ Turn off engine and engage park
brake.
▲ If included, raise seat bar and
move controls until both lock.
▲ Remove key to prevent
unauthorized starting.
▲ Use steps, grab-handles and
skid-resistant surfaces when
getting on or off the loader.
▲ Detach and store implements in
an area where children normally
do not play. Secure implement by
using blocks and supports.
Practice Safe Maintenance
▲ Understand procedure before doing
work. Use proper tools and
equipment, refer to Operator’s
Manual for additional information.
▲ Work in a clean dry area.
▲ Lower attached implement to the
ground and follow all shutdown
procedures before leaving the
operator’s seat to perform
maintenance.
▲ Allow implement to cool completely
before working on it.
▲ Disconnect battery ground cable (-)
before servicing or adjusting
electrical systems or before welding
on implement.
▲ Do not grease or oil implement
while it is in operation.
▲ Inspect all parts. Make sure parts
are in good condition & installed
properly.
▲ Remove buildup of grease, oil, or
debris.
▲ Remove all tools and unused parts
from implement before operation.
OFF
R
E
M
OV
E
Use Safety
Lights and Devices
▲ Slow moving tractors,
self-propelled equipment, and
towed implements can create a
hazard when driven on public
roads. They are difficult to see,
especially at night.
▲ Flashing warning lights and turn
signals are recommended
whenever driving on public roads.
3
11/23/ 15
SH35 Category 1 & 2 Skid Steer Quick Hitch 320-019M
Important Safety Information
Table of Contents
These are common practices that may or may not be applicable to the products described in
this manual.
Prepare for Emergencies
▲ Be prepared if a fire starts.
▲ Keep a first aid kit and fire
extinguisher handy.
▲ Keep emergency numbers for
doctor, ambulance, hospital, and
fire department near phone.
Wear
Protective Equipment
▲ Wear protective clothing and
equipment appropriate for the job.
Clothing should be snug fitting
without fringes and pull strings to
avoid entanglement with moving
parts.
▲ Prolonged exposure to loud noise
can cause hearing impairment or
hearing loss. Wear suitable
hearing protection such as
earmuffs or earplugs.
▲ Operating equipment safely
requires the operator’s full
attention. Avoid wearing radio
headphones while operating
machinery.
Use Seat Belt and ROPS
▲ Operate only skid steers equipped
with a Roll-Over Protective
Structure (ROPS) and seat belt.
▲ Fasten seat belt snugly and
securely to help protect against
serious injury or death from falling
and skid steer overturn.
▲ Wearing protective equipment
such as safety shoes, safety
glasses, hard hat, and ear plugs is
highly recommended.
911
Keep Riders Off
Machinery
▲ Never carry riders or use
machinery as a person-lift.
▲ Riders obstruct operator’s view.
▲ Riders could be struck by foreign
objects or thrown from the
machine.
▲ Never allow children to operate
equipment.
Tire Safety
▲ Tire changing can be dangerous
and should be performed by
trained personnel using the
correct tools and equipment.
▲ When inflating tires, use a clip-on
chuck and extension hose long
enough to allow you to stand to
one side and NOT in front of or
over the tire assembly. Use a
safety cage if available.
▲ When removing and installing
wheels, use wheel handling
equipment adequate for the
weight involved.
Avoid High
Pressure Fluids Hazard
▲ Escaping fluid under pressure can
penetrate the skin causing serious
injury.
▲ Avoid the hazard by relieving
pressure before disconnecting
hydraulic lines or performing work
on the system.
▲ Make sure all hydraulic fluid
connections are tight and all
hydraulic hoses and lines are in
good condition before applying
pressure to the system.
▲ Use a piece of paper or
cardboard, NOT BODY PARTS, to
check for suspected leaks.
▲ Wear protective gloves and safety
glasses or goggles when working
with hydraulic systems.
▲ DO NOT DELAY. If an accident
occurs, see a doctor familiar with
this type of injury immediately. Any
fluid injected into the skin or eyes
must be treated within
a few hours or
gangrene may
result.
4
SH35 Category 1 & 2 Skid Steer Quick Hitch 320-019M
11/23/15
Important Safety Information
Table of Contents
818-866C
Caution: Pinch Point
838-167C
Danger: Crushing Hazard
18440
18441
Safety Labels
Your Quick Hitch comes equipped with all safety labels in
place. They were designed to help you safely operate your
implement. Read and follow their directions.
1. Keep all safety labels clean and legible.
2. Refer to this section for proper label placement. Replace
all damaged or missing labels. Order new labels from your
nearest Land Pride dealer. To find your nearest dealer,
visit our dealer locator at www.landpride.com.
3. Some new equipment installed during repair requires
safety labels to be affixed to the replaced component as
specified by Land Pride. When ordering new components
make sure the correct safety labels are included in the
request.
4. Refer to this section for proper label placement.
To install new labels:
a. Clean surface area where label is to be placed.
b. Spray soapy water onto the cleaned area.
c. Peel backing from label and press label firmly onto the
surface.
d. Squeeze out air bubbles with edge of a credit card or
with a similar type of straight edge.
5
11/23/ 15
SH35 Category 1 & 2 Skid Steer Quick Hitch 320-019M
Introduction
Table of Contents
Introduction
The parts on your Quick Hitch have been specially
designed by Land Pride and should only be replaced with
genuine Land Pride parts. Contact a Land Pride dealer if
customer service or repair parts are required. Your Land
Pride dealer has trained personnel, repair parts, and
equipment needed to service the implement.
Serial Number
Model No. _____________Serial No. ______________
For quick reference and prompt service, record model
and serial number in the spaces provided above and
again on warranty page 15. Always provide model
number and serial number when ordering parts and in all
correspondences with your Land Pride dealer. Refer to
Figure 1 for location of your serial number plate.
Serial Number Plate Location
Figure 1
Further Assistance
Your dealer wants you to be satisfied with your new Quick
Hitch. If for any reason you do not understand any part of
this manual or are not satisfied with the service received,
the following actions are suggested:
1. Discuss the matter with your dealership service
manager making sure that person is aware of any
problems you may have and has had the opportunity
to assist you.
2. If you are still not satisfied, seek out the owner or
general manager of the dealership, explain the
problem, and request assistance.
3. For further assistance write to:
Land Pride
Service Department
P.O. Box 5060
Salina, KS 67402-5060
E-mail address
lpservicedept@landpride.com
18441
Land Pride welcomes you to the growing family of new
product owners.
This Quick Hitch has been designed with care and built
by skilled workers using quality materials. Proper
assembly, maintenance, and safe operating practices will
help you get years of satisfactory use from this machine.
Application
The SH35 Series Skid Steer Quick Hitch is designed and
built by Land Pride to provide quick and easy three-point
attachment to category 1 or 2 implements that are not
driven or powered by a PTO shaft. Box blades, landscape
rakes, soil pulverizers, hydraulically driven power rakes,
and other like implements work extremely well with this
hitch. Rental yards, implement dealers, and owners of
larger implement fleets will find that the SH35 serves an
excellent tool for spotting, relocating, and organizing
implements on large lots. This unit also has expanded
versatility with use of a class 2 receiver and convenient
storage for a ball hitch. An adjustable top hook makes
attachment to a broader range of implements even
easier.
See “Specifications & Capacities” on page 11 and
“Features & Benefits” on page 12 for additional
information and performance enhancing options.
Using This Manual
•
This Operator’s Manual is designed to help familiarize
you with safety, assembly, operation, adjustments,
troubleshooting, and maintenance. Read this manual
and follow the recommendations to help ensure safe
and efficient operation.
• The information contained within this manual was
current at the time of printing. Some parts may change
slightly to assure you of the best performance.
• To order a new Operator’s or Parts Manual, contact
your authorized dealer. Manuals can also be
downloaded, free-of-charge, from our website at
www.landpride.com
Terminology
“Right” or “Left” as used in this manual is determined by
facing the direction the machine will travel while in use
unless otherwise stated.
Definitions
Owner Assistance
The Online Warranty Registration should be completed
by the dealer at the time of purchase. This information is
necessary to provide you with quality customer service.
IMPORTANT: A special point of information related
to the following topic. Land Pride’s intention is this
information must be read & noted before continuing.
NOTE: A special point of information that the
operator should be aware of before continuing.
6
SH35 Category 1 & 2 Skid Steer Quick Hitch 320-019M
11/23/15
Section 1: Assembly & Setup
Table of Contents
Section 1: Assembly & Setup
Skid Steer Loader Requirements
This SH35 Quick Hitch is designed for skid steer loaders.
Skid Steer Loader Hook-Up
Refer to Figure 1-1
!
CAUTION
Do not stand between skid steer loader and implement during
hookup.
1. Drive skid steer loader slowly to the Quick Hitch
making sure front hitch plate of the skid steer loader
is parallel with the Quick Hitch frame.
2. Tilt top of skid steer loader hitch plate slightly
forward.
3. Place top of skid steer loader hitch plate under the
top angled bar of the Quick Hitch.
4. Slowly lift skid steer loader hitch until Quick Hitch and
skid steer loader hitch have come together.
Skid Loader Hook-Up
Figure 1-1
IMPORTANT: Maximum weight of attached
implement shall not exceed 2,800 lbs. at 24” from
implements’ lower hitch pins.
NOTE: Ballast may need to be added to your skid
steer loader to maintain steering control. Refer to
your skid steer loader Operator Manual to determine
whether or not to add ballast.
IMPORTANT: Some Cat. 1 and Cat. II implements
may not meet Quick Hitch standards.
Any modification made to the Quick Hitch or
implement to accommodate hook-up could void
the warranty.
22137
Top Angle Bar
Bottom Slots
Positioning Pins with
Cotter Hair Pins
5. Push skid steer loader release handles down to drive
hitch pins through bottom slots in the Quick Hitch
frame and to lock release handles down.
Center Hook Adjustment
Refer to Figure 1-2 & Figure 1-3
The Quick Hitch top hook normally is adjusted for a
standard Category I or Category II configuration. Adjust
top hook if implement being attached is not a true
standard Category I or II configuration. (See Figure 1-3)
!
DANGER
Crushing Hazard between Quick Hitch and Implement. Do not
allow anyone to stand between the Quick Hitch and implement
while backing-up to implement. Never operate hydraulic lift
controls while someone is near the lift arms
and/or Quick Hitch.
1. Lower skid steer lift arms and carefully move Quick
Hitch forward to align its lower support hooks with
implement’s lower 3-point hitch pins. Verify upper
Quick Hitch top hook also aligns with implement’s
center hitch pin. (See Figure 1-3 on page 7.)
2. Skip to Implement Hook-Up if the three hooks align
with implement’s three hitch pins.
3. Engage park brake, shut engine off, and remove
switch key before dismounting from skid steer loader.
4. Remove hairpin cotter and clevis pins securing Quick
Hitch upper hook. Move hook up or down to align with
implement’s upper hitch pin.
5. Replace clevis pins and their hairpin cotters.
Upper Hook Adjustment
Figure 1-2
NOTE: Skid steer hook-up is required before
proceeding with center hook adjustment.
Clevis Pins
Upper Hook
Hairpin Cotter
22140
7
11/23/ 15
SH35 Category 1 & 2 Skid Steer Quick Hitch 320-019M
Section 1: Assembly & Setup
Table of Contents
Implement Hook-Up
Refer to Figure 1-1
Determine hitch category of implement being hooked up.
• Category I hitches will have 7/8” diameter lower hitch
pins and a 3/4” diameter upper hitch pin.
• Category II hitches will have 1 1/8” diameter lower
hitch pins and a 1” diameter upper hitch pin.
Remove 1/2” x 3” positioning pins to reposition lower
3-point hooks on the Quick Hitch. Move hooks to the
inward positions if implement is a Category 1 hitch and to
the outward positions if implement is a Category II hitch.
Replace 1/2” x 3” positioning pins and secure with cotter
hair pins.
!
DANGER
Crushing Hazard between Quick Hitch and Implement. Do not
allow anyone to stand between the Quick Hitch and implement
during hook-up operations. Never operate hydraulic lift
controls while someone is near the lift arms
and/or Quick Hitch.
!
DANGER
Hydraulic fluid under pressure can penetrate skin. Wear
protective gloves and safety glasses or goggles when working
NOTE: Hook-up of Quick Hitch to the skid steer
loader is required before proceeding with hook-up to
implement.
.
Implement Hook-Up
Figure 1-3
18442
Quick Hitch Bushing
Implement Linchpin
Implement’s Lower Hitch Pin
Release Handle
Standard Category I
Connect Top Hook to Lower
Center Hitch Pin/Bolt
with hydraulic systems. Use a piece of cardboard or wood
rather than hands when searching for hydraulic leaks. If
hydraulic fluid is injected into the skin, it must be surgically
removed within a few hours by a doctor or gangrene may
result.
!
CAUTION
Release Handles have areas where pinching can occur. Keep
hands, fingers and other body parts away from pivoting areas
of the release handles. Always use handle grips.
Refer to Figure 1-3
1. Two 320-048D lower bushings are shipped wire tied
to Land Pride Skid Steer Quick Hitch. Place bushings
over implement’s lower 7/8” hitch pins. This will
provide a tighter and more secure mounting in the
two lower Quick Hitch hooks. Do not use bushings
when hitching to a Category II implement.
2. Make certain implement’s upper and lower hitch pins
are secured.
3. Place Quick Hitch release handles in the down
position as shown.
4. With arms of the skid steer loader lowered, carefully
move loader up to (Cat. I or Cat. II) implement to align
its upper and lower support hooks with implement’s
3-point hitch pins.
5. Slowly raise skid steer loader lift arms until lower
Quick Hitch hooks lock over implement’s 3-point
hitch pins.
8
SH35 Category 1 & 2 Skid Steer Quick Hitch 320-019M
11/23/15
Section 1: Assembly & Setup
Table of Contents
Spare Bushings
Additional bushings may be purchased from your local
Land Pride dealer so that more than one implement is
readily available for quick hook-up.
IMPORTANT: Make certain implement’s top
3-point hitch pin is captured by the Quick Hitch top
3-point hook.
Lower Bushings
Part No. Part Description
320-034A 2- Stepped Bushings CAT. l to CAT. lll Adapter
320-048D Spacer Tube 1.44” O.D. x .91” I.D. x 1 9/32” lg
320-044D Spacer Tube 1.44” O.D. x .93” I.D. x 1 5/8” lg.
320-045D Spacer Tube 1.44” O.D. x .93” I.D. x 1 15/16” lg.
320-050D Spacer Tube 1.44” O.D. x .93” I.D. x 2 3/16” lg.
320-051D Spacer Tube 1.44” O.D. x .93” I.D. x 2 7/16” lg.
325-017D Spacer Tube 1.44” O.D. x .93” I.D. x 3 15/16” lg.
320-052D Spacer Tube 1.44” O.D. x .93” I.D. x 3 1/2” lg.
Implement Unhooking
Refer to Figure 1-4
!
DANGER
Crushing Hazard between Quick Hitch and Implement. Do not
allow anyone to stand between Quick Hitch and implement
while unhooking from implement. Never operate hydraulic lift
controls while someone is directly behind the tractor.
!
DANGER
Engage parking brake, shut off skid steer loader, and remove
key before dismounting.
1. Raise skid steer loader arms so implement is off the
ground.
2. Engage park brake, shut engine off, and remove
switch key before dismounting from loader.
3. Pull release handles up. See Figure 1-4.
4. Restart skid steer loader, lower loader arms until
implement is on the ground, and Quick Hitch is clear
of implement’s hitch pins.
5. Pull away from implement.
Release Handles Pointing Up
Figure 1-4
22138
9
11/23/ 15
SH35 Category 1 & 2 Skid Steer Quick Hitch 320-019M
Section 2: Operating Instructions
Table of Contents
Transporting and Use
!
CAUTION
Comply with all federal, state, and local laws when traveling
on public roads.
!
DANGER
Always use accessory lights and other available warning
devices to alert other vehicle operators of your presence when
traveling on public roads night and day.
!
DANGER
The release handles should always be rotated down when
using the Quick Hitch.
Operating Instructions
Once you have familiarized yourself with the Operator’s
Manual and properly attached your Land Pride SH35
Quick Hitch to the skid steer loader, you should be just
about ready to start Quick Hitch “management and
handling” of your compatible Category l and Category II
3-point implements.
You will notice we emphasize “management and
handling” when we refer to your implements. If you are
going to gain the benefit of owning a Land Pride SH35
Skid Steer Quick Hitch you will need to park your
implements on a firm surface ensuring that the lower
hitch pins and top-link remain upright or oriented for
future Quick Hitch alignment and attachment. Allowing
the lower hitch pins and top link to tumble forward into the
dirt or mud will not be acceptable or compatible with this
fast hook-up system. This simply is a better way to
manage your time, your implements, and your
investment.
Now you are ready to use your Quick Hitch. Put your
Quick Hitch release handles in the down and locked
position. Start your loader and slowly move forward
centering on the implement you want to attach. Lower
your three-point so the Quick Hitch lower hooks and top
link hook line up under the implements lower hitch pins
and top-link pin simultaneously. Slowly raise the Quick
Hitch until all three pins are captured and the lower pins
automatically lock in place. You should be ready for
transport.
When you are ready to detach, position the implement
over a firm surface or prepared docking point that will
keep the lower hitch pins and top-link properly oriented
for future attachment. With the implement still off the
ground, set the parking brake, turn off the loader, remove
the key, get off the loader, disconnect implement
hydraulic hoses if used and raise the Quick Hitch release
handles. Now get back on the loader, start the engine,
slowly lower the implement until it is on the ground and
the Quick Hitch releases. Slowly back-up until you are
safely clear. With a little practice you should get very
good at hooking and unhooking quickly.
Section 2: Operating Instructions
10
SH35 Category 1 & 2 Skid Steer Quick Hitch 320-019M
11/23/15
Section 3: Maintenance & Lubrication
Table of Contents
Section 3: Maintenance & Lubrication
Lubrication
Pivot points
Multipurpose Spray Lube
Quantity = Generously
18443
Maintenance
Proper servicing and adjustments are key to the long life
of any implement. With careful and systematic
inspection, you can avoid costly maintenance, time, and
repair.
After using your Skid Steer Quick Hitch for several hours,
check all bolts to be sure they are tight.
Replace any worn, damaged, or illegible safety labels by
obtaining new labels from your Land Pride dealer.
As
Required
50
Hrs
Multi-purpose
spray lube
Multi-purpose
grease lube
Multi-purpose
oil lube
Intervals in hours at which
lubrication is required
Lubrication
Legend
11
11/23/ 15
SH35 Category 1 & 2 Skid Steer Quick Hitch 320-019M
Section 4: Specifications & Capacities
Table of Contents
Section 4: Specifications & Capacities
SH35 Series Skid Steer Quick Hitch
List Specifications & Capacities
Hitch Standard Category 1 & II, 3-point with adjustable top hitch
Overall Width 46 7/8”
Height 25”
Length 15 1/2”
Weight 225 lbs.
Lower 3-Point Automatic Lock
Maximum Lift Capacity 2,800 lbs at 24” from implements’, lower hitch pins.
26875
12
SH35 Category 1 & 2 Skid Steer Quick Hitch 320-019M
11/23/15
Section 5: Features & Benefits
Table of Contents
SH35 Series Skid Steer Quick Hitch
Features Benefits
Fits Cat. 1 or 2 implements Easily fits Cat. 1 or 2 non-PTO implements – Fits all Land Pride implements.
Automatic lock
on lower 3-point arms
Don’t have to get off of skid steer loader when hooking up to an implement.
Adjustable top hook Helps match up to implement.
Class II receiver
and storage for ball hitch
A class II ball hitch can be inserted into the hitch for towing, also can be used for storing a
ball hitch.
Universal skid steer plate Fits most skid steer loaders.
Ball Hitch Receiver and Storage Rack
The Quick Hitch is equipped so that a ball hitch can be
assembled to the hitch. The Quick Hitch can then be used to
pull an implement with a ball hitch. The ball hitch may be
stored on top of the Quick Hitch when it is not in use.
Figure 4-1
Section 5: Features & Benefits
18445
13
11/23/ 15
SH35 Category 1 & 2 Skid Steer Quick Hitch 320-019M
Section 6: Torque Values Chart
Table of Contents
Section 6: Torque Values Chart
Torque Values Chart for Common Bolt Sizes
Bolt Head Identification Bolt Head Identification
Bolt Size
(inches) Grade 2 Grade 5 Grade 8
Bolt Size
(Metric) Class 5.8 Class 8.8 Class 10.9
in-tpi
1
N · m
2
ft-lb
3
N · m ft-lb N · m ft-lb mm x pitch
4
N · m ft-lb N · m ft-lb N · m ft-lb
1/4" - 20 7.45.611 81612M 5 X 0.8 436597
1/4" - 28 8.5 6 13 10 18 14 M 6 X 1 7 5 11 8 15 11
5/16" - 18 15 11 24 17 33 25 M 8 X 1.25 17 12 26 19 36 27
5/16" - 24 17 13 26 19 37 27 M 8 X 1 18 13 28 21 39 29
3/8" - 16 27 20 42 31 59 44 M10 X 1.5 33 24 52 39 72 53
3/8" - 24 31 22 47 35 67 49 M10 X 0.75 39 29 61 45 85 62
7/16" - 14 43 32 67 49 95 70 M12 X 1.75 58 42 91 67 125 93
7/16" - 20 49 36 75 55 105 78 M12 X 1.5 60 44 95 70 130 97
1/2" - 13 66 49 105 76 145 105 M12 X 1 90 66 105 77 145 105
1/2" - 20 75 55 115 85 165 120 M14 X 2 92 68 145 105 200 150
9/16" - 12 95 70 150 110 210 155 M14 X 1.5 99 73 155 115 l215 160
9/16" - 18 105 79 165 120 235 170 M16 X 2 145 105 225 165 315 230
5/8" - 11 130 97 205 150 285 210 M16 X 1.5 155 115 240 180 335 245
5/8" - 18 150 110 230 170 325 240 M18 X 2.5 195 145 310 230 405 300
3/4" - 10 235 170 360 265 510 375 M18 X 1.5 220 165 350 260 485 355
3/4" - 16 260 190 405 295 570 420 M20 X 2.5 280 205 440 325 610 450
7/8" - 9 225 165 585 430 820 605 M20 X 1.5 310 230 650 480 900 665
7/8" - 14 250 185 640 475 905 670 M24 X 3 480 355 760 560 1050 780
1" - 8 340 250 875 645 1230 910 M24 X 2 525 390 830 610 1150 845
1" - 12 370 275 955 705 1350 995 M30 X 3.5 960 705 1510 1120 2100 1550
1-1/8" - 7 480 355 1080 795 1750 1290 M30 X 2 1060 785 1680 1240 2320 1710
1-1/8" - 12 540 395 1210 890 1960 1440 M36 X 3.5 1730 1270 2650 1950 3660 2700
1-1/4" - 7 680 500 1520 1120 2460 1820 M36 X 2 1880 1380 2960 2190 4100 3220
1-1/4" - 12 750 555 1680 1240 2730 2010
1
in-tpi = nominal thread diameter in inches-threads per inch
1-3/8" - 6 890 655 1990 1470 3230 2380
2
N· m = newton-meters
1-3/8" - 12 1010 74 5 2270 1670 3680 2710
3
ft-lb= foot pounds
1-1/2" - 6 1180 870 2640 1950 4290 3160
4
mm x pitch = nominal thread diameter in millimeters x thread
pitch
1-1/2" - 12 1330 980 2970 2190 4820 3560
Torque tolerance + 0%, -15% of torquing values. Unless otherwise specified use torque values listed above.
5.8
8.8
10.9
15
11/23/ 15
SH35 Category 1 & 2 Skid Steer Quick Hitch 320-019M
Section 7: Warranty
Table of Contents
Warranty
Land Pride warrants to the original purchaser that this Land Pride product will
be free from defects in material and workmanship beginning on the date of
purchase by the end user according to the following schedule when used as
intended and under normal service and conditions for personal use.
Overall Unit and Driveline: One year Parts and Labor
This Warranty is limited to the repair or replacement of any defective part by
Land Pride and the installation by the dealer of any such replacement part, and
does not cover common wear items such as blades, belts, tines, etc. Land Pride
reserves the right to inspect any equipment or parts which are claimed to have
been defective in material or workmanship.
This Warranty does not apply to any part or product which in Land Pride’s
judgment shall have been misused or damaged by accident or lack of normal
maintenance or care, or which has been repaired or altered in a way which
adversely affects its performance or reliability, or which has been used for a
purpose for which the product is not designed. Misuse also specifically includes
failure to properly maintain oil levels, grease points, and driveline shafts.
Claims under this Warranty must be made to the dealer which originally sold
the product and all warranty adjustments must be made through such dealer. Land
Pride reserves the right to make changes in materials or design of the product at
any time without notice.
This Warranty shall not be interpreted to render Land Pride liable for damages
of any kind, direct, consequential, or contingent to property. Furthermore, Land
Pride shall not be liable for damages resulting from any cause beyond its
reasonable control. This Warranty does not extend to loss of crops, any expense
or loss for labor, supplies, rental machinery or for any other reason.
No other warranty of any kind whatsoever, express or implied, is made
with respect to this sale; and all implied warranties of merchantability and
fitness for a particular purpose which exceed the obligations set forth in this
written warranty are hereby disclaimed and excluded from this sale.
This Warranty is not valid unless registered with Land Pride within 30 days from
the date of purchase by the end user.
Section 7: Warranty
IMPORTANT: The Online Warranty Registration should be completed by the dealer at the time of
purchase. This information is necessary to provide you with quality customer service.
Model Number ____________________ Serial Number ____________________
Corporate Office: P.O. Box 5060
Salina, Kansas 67402-5060 USA
www.landpride.com
